Documentation issue status Documentation issue status Version Comment First preliminary version (draft) Adaptations in the block diagram, corrected feature list, adaptation of the interface designation, adaptations in the BIOS CB6263 Version: 0.2...
All the components are supplied in particular hardware and software configurations appropriate for the application. Modifications to hardware or software configurations other than those described in the documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG. Personnel qualification This description is only intended for trained specialists in control, automation and drive technology who are familiar with the applicable national standards.
Page 8
Safety instructions The specified limits for electrical and technical data must be adhered to. Version: 0.2 CB6263...
Overview Properties The CB6263 is conceived as a compact PC. It offers basic functions, on-board RAM and a powerful CPU of the Intel® Bay trail generation in the smallest space. The CB6263 provides 1x DisplayPort/HDMI, 1x USB2.0, 1x USB3.0 and 2x Gigabit-LAN as I/O interfaces on its front panel.
Cards of different types have different recesses (keys). Depending on which types are supported, ports can accept expansion cards of one or more types. The M.2 socket of the CB6263 supports M.2 modules with Key B. SATA signals that allow an SSD to be connected are output via the interface.
Connections Plug connector overview The plug connections of the CB6263 board are summarized in the illustration below. The function of the respective plug connection can be taken from the table below the illustration, as can the page of the manual on which further information about this connection can be read.
USB 2.0 connection. Limitations in the maximum cable length are also no rarity. All of these interface-specific requirements are to be taken from the re- spective specifications and observed accordingly. Version: 0.2 CB6263...
The connection for the power supply is implemented as a 2x2-pin housing plug. The main power supply (24 V) for the module is on pin 3. Fig. 3: CB6263 Vin 90° plug As the plug is a 90° plug, the plug symbol in the illustration is oriented to what you see when you look at the board from the side (instead of from above).
As the plug is a 90° plug, the plug symbol in the illustration is oriented to what you see when you look at the board from the side (instead of from above). Fig. 4: CB6263 LAN Pin assignment of LAN connector: Pin...
Ground 3.3 V 3.3 V supply voltage Switching to HDMI DisplayPort signals are led out via the interface by default. With the use of a level shifter cable the board switches the DisplayPort specification 1.1 automatically to HDMI signals. CB6263 Version: 0.2...
BIOS setup is only required if the operating system does not offer USB support. This function should not be selected for settings in the setup and for booting Windows with a USB mouse and keyboard connected, because this would lead to considerable performance limitations. Fig. 6: CB6263 USB 2.0 Pin assignment of USB 2.0 connector: Pin Name...
USB support. This function should not be selected for settings in the setup and for booting Windows with a USB mouse and keyboard connected, because this would lead to considerable performance limitations. Fig. 7: CB6263 USB 3.0 Pin assignment of USB 3.0 connector: Pin...
Internal: M.2 (Key B) The CB6263 is equipped with an M.2 socket, into which an M.2-2242 card (Key B) can be inserted. SATA signals (up to 3 Gb/s), which enable the connection of an M.2-SSD card, are fed out via this socket.
Page 21
(not led out) ANTCTL3 SIM DETECT (not led out) Power good RESET# SUSCLK Suspend clock Configuration pin CFG1 3.3 V Standby supply voltage S3.3V Ground 3.3 V Standby supply voltage S3.3V Ground 3.3 V Standby supply voltage S3.3V Configuration pin CFG2 CB6263 Version: 0.2...
The BAseCon140 plug connector (Samtec HSEC-170-01-L-DV-A-K-TR) enables the flexible extension of the IO functions of the CB6263. It provides up to 8 PCIe lanes, of which 4 can be multiplexed with SATA2.0 (3G) signals and 4 with USB 3.0 signals. In addition, DisplayPort, HSIC, SMBus and 1Wire signals are fed out via the BAseCon plug.
Page 23
(not led out) (GND) (not led out) PECLK5/ PECLK6 (not led out) USBC_SBU1 (GND) (GND) (not led out) PECLK5#/ PECLK6# (not led out) USBC-SBU2 (GND) (GND) (not led out) USB2-4# USB2-8 D# (not led out) (GND) (GND) CB6263 Version: 0.2...
Page 24
DP / HDMI DP/DVI# DDCC/ DisplayPort Aux +/ switchover DPAUX DDC Clock DisplayPort Hot Plug DPHPD DDCD/ DisplayPort Aux - / Detect DPAUX# DDC Data Ground Ground DisplayPort Lane 0 + DPL0 DPL1 DisplayPort Lane 1 + Version: 0.2 CB6263...
Page 25
Connections Description Signal Signal Description DisplayPort Lane 0 - DPL0# DPL1# DisplayPort Lane 1 - Ground Ground DisplayPort Lane 2 + DPL2 DPL3 DisplayPort 3 + DisplayPort Lane 2 - DPL2# DPL3# DisplayPort 3 - CB6263 Version: 0.2...
6.5.3 Internal: FAN The CB6263 has a 3-pin fan connection (JST BM03B-SRSS-TBT(LF)-(SN)). This enables a fan with a supply voltage of 5 V to be connected directly to the module. The connection has a speed monitoring function. The connected fan must supply a corresponding tachometer signal if this is to be used.
6.5.4 Internal: RTC The CB6263 can be connected to an external RTC battery via a bipolar housing plug (JST BM02B-SRSS- TBT(LP)(SN)) to provide power to the integrated clock even if there is no power supply. The battery voltage must not exceed 3.3V.
It should also be noted that the settings shown in the setup menus below are not necessarily the recommended or default settings. Which settings must be selected depends on the application scenario in which the board is operated. Version: 0.2 CB6263...
BIOS Main CB6263 Board Information Set the Date. Use Tab to switch between Date elements. Board CB6263 Revision 1 Bios Version 0.78 Processor Information BayTrail SoC D0 Stepping Brand String Intel® Atom™ CPU E3827@1.74GHz Max CPU Speed 1740 MHz CPU Signature 30679 Processor Cores 2 →←: Select Screen Microcode Patch 90a...
ESC: Exit Bios entry Options PC Health Status CPU dig. None 1.0 V None VCCCORE None 5 V None 12 V None Memory VDD None 3.3 V None Fan 1 None Fan 2 None MB Temp None Memory Temp None PwrCtrlTemp None CB6263 Version: 0.2...
Submenu: see Socket CPU Information [} 33] CPU Thermal Configuration Submenu: see CPU Thermal Configuration [} 34] CPU speed None 64 bit None Limit CPUID Maximum Enabled / Disabled Execute Disable Bit Enabled / Disabled Intel (VMX) Virtualization Technology Disabled / Enabled Version: 0.2 CB6263...
Page 33
Socket CPU Information CPU signature None Matchcode Patch None Min CPU Speed None Processor Cores None Intel HAT Technology None Intel VT-x Technology None L1 Data Cache None L1 Code Cache None L2 Cache None L3 Cache None CB6263 Version: 0.2...
SATA Speed Report Gen2 SATA ODD Port No ODD SATA Mode AHCI Mode Serial-ATA Port 0 Enabled SATA Port 0 HotPlug Disabled Serial-ATA Port 1 Enabled SATA Port 1 HotPlug Disabled SATA Port0 Not Present SATA Port1 Not Present Version: 0.2 CB6263...
ESC: Exit Bios entry Options Bootloader version None Firmware version None Mainboard serial no None Mainboard Prod. Date (Week.Year) None Mainboard BootCount None Mainboard operation time None Voltage (Min/Max) None Temperature (Min/Max) None WDT OSBoot Timeout Disabled CB6263 Version: 0.2...
Option ROM execution Network Do not launch / UEFI / Legacy Storage Do not launch / UEFI / Legacy Video Do not launch / UEFI / Legacy Other PCI devices Do not launch / UEFI / Legacy Version: 0.2 CB6263...
High Precision Timer Enabled / Disabled Restore AC Power Loss Power Off / Power On / Last State Onboard Device Configuration Onboard Gigabit LAN 1 Enabled / Disabled Onboard Gigabit LAN 2 Enabled / Disabled M.2-SATA Configuration Pins None Version: 0.2 CB6263...
Page 50
F2: Previous Values USB Port 3 [Enabled] F3: Optimized Values F4: Save&Exit ESC: Exit BIOS entry Options PCI Boot Configuration USB Mode XHCI / EHCI USB Per Port Control Enabled / Disabled USB Port X Enabled / Disabled Version: 0.2 CB6263...
Page 51
PCI Express Port 3 Enabled / Disabled Hot Plug Enabled / Disabled Speed Auto / Gen1 / Gen2 Extra Bus Reserved 0..7 Reserved Memory 1..20 Reserved Memory Alignment 0..31 Reserved I/O 4K / 8K / 12K / 16K / 20K CB6263 Version: 0.2...
Page 54
Save all Secure Boot variables Press enter key Platform Key(PK) Press enter key Key Exchange Keys Press enter key Authorized Signatures Press enter key Forbidden Signatures Press enter key Authorized TimeStamps Press enter key OsRecovery Signatures Press enter key Version: 0.2 CB6263...
Legacy / UEFI / Dual Fixed Boot Order Priorities Boot Option #1-19 Here you can set the order of the boot media to be used Advanced Fixed Boot Order Parameters Submenu see: Advanced Fixed Boot Order Parameters [} 56] CB6263 Version: 0.2...
Before a planned BIOS update, it is essential to ensure that the BIOS file to be reloaded is really re- leased for exactly this board and for exactly this board version. If an inappropriate file is used, the board will inevitably not boot afterwards. Version: 0.2 CB6263...
5 to 9 Hz, amplitude 3.5 mm 9 to 500 Hz, 10 m/s², for packed boards Note on impact and vibration resistance The specifications for impact and vibration resistance refer only to the motherboard itself without heat sink, memory module, cabling, etc. CB6263 Version: 0.2...
It is the end customer's responsibility to ensure that the die temperature of the processor does not exceed 110 °C! Continuous overheating can destroy the board! If the temperature exceeds 110 °C, the ambient temperature needs to be reduced. Ensure sufficient air cir- culation if necessary. Version: 0.2 CB6263...
Support and Service 10.1 Beckhoff Support Beckhoff Support offers you comprehensive technical assistance, helping you not only with the application of individual Beckhoff products, but also with other, wide-ranging services: • world-wide support • design, programming and commissioning of complex automation systems •...
Codes are explained in the document "Aptio™ 5.x Status Codes" from American Megatrends®, which is available from the website http://www.ami.com. In addition, the following OEM POST Codes are output: Code Description BIOS-API started PCA9535 started PWRCTRL firmware update started Version: 0.2 CB6263...
API access to power supply unit 36-39 Reserved 5C-5D NCT7491 70-73 POST Code output 88-89 Slave address defined by BIOS 92-93 I210 default A0-A7 Reserved for DDR B0-B3 Power controller (access via BIOS-API) B8-BB Power controller (access via BIOS-API) CB6263 Version: 0.2...