Table of Contents
Advertisement
Quick Links
Installation and Service Manual
SUBMERSIBLE SEW GE PUMP
RECESSED IMPELLER
Model S4LRC
NOTE! To the installer: Please make sure
you provide this manual to the owner of
the equipment or to the responsible party
who maintains the system.
For use with product
built with GE motor.
03/11
Item # E-03-315
Part # 5625-315-1
© 2011 Pentair Pump Group,Inc.
Advertisement
Table of Contents
Related Manuals for Hydromatic S4LRC
Summary of Contents for Hydromatic S4LRC
- Page 1 Installation and Service Manual SUBMERSIBLE SEW GE PUMP RECESSED IMPELLER Model S4LRC NOTE! To the installer: Please make sure you provide this manual to the owner of the equipment or to the responsible party who maintains the system. For use with product built with GE motor.
-
Page 2: General Information
Pumps Not Operating or Pump: General in Storage: The S4LRC submersible pumps Information Pumps with carbon ceramic seals are supplied for 3 phase and for must have impellers manually 200, 230, 460 and 575 volts. rotated (6 revolutions) after Pump is supplied with 30 feet... - Page 3 It is recommended that the only if sump level rises to the pump, a magnetic starter with Hydromatic control panel be used WIRE SIZE AND MAXIMUM LENGTH (FEET) FOR REMOTE LOCATION OF CONTROL PANEL BASED ON A 2% VOLTAGE DROP (230 VOLTS 3 PHASE)
-
Page 4: Pump Installation
Overload Heaters: check valve the line pressure can Wiring diagrams are provided be cut off. Single pump systems with panel for making connections. If the Hydromatic electrical panel are sometimes installed without a An extra set of diagrams is used, starters... -
Page 5: Pump Operations
2. Open all discharge valves and delta Addendum readjusting cord length. allow water to rise in sump pump. S4LRC-701. In either simplex or duplex system 3. Turn H-O-A switch to Hand the lower or turn-off control is position on one pump and... -
Page 6: Pump Maintenance
6. Turn both H-O-A switches Field Service on Motor: to Auto position and allow If a seal failure unit is used, no All S4LRC submersible motors sump to fill to the override attention is necessary as long can be serviced (out of warranty) control level. - Page 7 ⁄ " deep, and ⁄ -20 UNF, ⁄ oil or Hydromatic special 6. After ring is removed, turn deep into the stator). This submersible oil. Fill chamber housing upright and bump on holding spot is drilled through...
-
Page 8: Pump Troubleshooting
Pump runs but will not shut off. obtained from 4. Overload heater on starter may Hydromatic factory. be tripped. Push to reset. 1. Pump may be air locked. Turn pump off and let set for several 11. IMPORTANT: Do not use minutes, then restart. - Page 9 Check in sump to be sure control control. Hydromatic is free. S4LRC submersible motors can operate for extended periods 3. Selector switch may be in the out of water without burning Hand position. up the winding, but the heat...
-
Page 10: Parts List
S4LRC Parts List For use with product built with GE motor. ORDERING REPLACEMENT PARTS: Product improvements are made from time to time. The latest part design will be furnished as long as it is interchangeable with the old part.When ordering replacement parts, always furnish the following information: (1) pump serial number, (2) pump model and size, (3) part description, (4) part number, (5) impeller diameter (if ordering impeller), (6) quantity required, and (7) shipping instructions. - Page 11 S4LRC...
- Page 12 Pump Notes...
- Page 13 Pump Notes...
-
Page 14: Standard Limited Warranty
12 months from the date of shipment from Hydromatic or 18 months from the manufacturing date, whichever occurs first - provided that such products are used compliance with the requirements of the Hydromatic catalog and technical manuals for use in pumping raw sewage, municipal wastewater or similar, abrasive free non-corrosive liquids. -
Page 16: Start-Up Report
Acknowledge that all information is accurate and proper procedures have been followed. Customer: ___________________________________________________________________ Date: _____________ Start-up Technician:___________________________________________________________ Date: _____________ Send to Warranty Manager, 1101 Myers Parkway, Ashland, OH 44805 or Fax to 419-207-3344 or email to startupreport@hydromatic.com or submit online at http://forms.pentairliterature.com/startupform/startupform.asp?type=h...
Need help?
Do you have a question about the S4LRC and is the answer not in the manual?
Questions and answers