Hydromatic SHEF50 Installation And Service Manual
  1. Manuals
  2. Brands
  3. Hydromatic Manuals
  4. Water Pump
  5. SHEF50
  6. Installation and service manual

Hydromatic SHEF50 Installation And Service Manual

Submersible effluent pump
Hide thumbs Also See for SHEF50:
Table of Contents

Advertisement

Quick Links

Download this manual
SHEF50/SHEF100
Submersible Effluent Pump
NOTE! To the installer: Please make sure you provide
this manual to the owner of the pumping equipment or to
the responsible party who maintains the system.
Pump Installation and Service Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SHEF50 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Hydromatic SHEF50

Summary of Contents for Hydromatic SHEF50

  • Page 1 Pump Installation and Service Manual SHEF50/SHEF100 Submersible Effluent Pump NOTE! To the installer: Please make sure you provide this manual to the owner of the pumping equipment or to the responsible party who maintains the system.

  • Page 2: General Information

    (gaseous) or sump diameter is 24" for should be installed in every possible septic sump. SHEF50 & 30" for SHEF100). pump for greater protection. 2. Do not set pump directly on Contact your Hydromatic...

  • Page 3: Typical Installation

    Typical Installation SHEF50 SHEF100...

  • Page 4: Pump Servicing

    Check local codes b. pump motor or bearings design point of pump (65' requirements before installation. may be defective SHEF50, 90' SHEF100). Only competent electrician should make the installations. c. start capacitor in motor may 13.Floats not hanging free in have failed the sump.
  • Page 5 (1ø) or remove RESISTANCE discolored, to cloudy, and finally splice connectors (3ø). If SHEF50 SHEF100 to a milky white. 1ø Start 1ø Main 3ø Bal. 1ø Start 1ø Main 3ø Bal. stator is visibly burned, motor 115V 6.53...
  • Page 6 3. When installing a replacement 12.Add a drop of Locktite 222 Pump bearing, press only on the shaft screw Servicing inner face and make sure the impeller on hand tight. The the bearing is flush against the impeller (#11) will force the snap ring.

  • Page 7: Pump Troubleshooting

    4. Pump head may be too trips when pump starts. high. Pump cannot deliver 1. Inlet in pump base may be water over (SHEF50) 65' clogged. Remove pump and or (SHEF100) 90' vertical. clean out openings. Pump must be sized to...

  • Page 8: Parts List

    SHEF50/100 Parts List 50 (51867-004-7) 100 (51871-002-7) 3-PHASE WIRING LOW VOLTAGE (230V) HIGH VOLTAGE (460V) MODEL – SHEF50/SHEF100 THREE PHASE Ref. No. Part No. Description Qty. Ref. No. Part No. Description Qty. 00060-000-5 Handle 01754-000-1 Locktite Sealant — 00056-022-2 Housing, Motor...
  • Page 9 Motor Assembly, 230V, SHEF100 12709-000-2 Adapter, SHEF100 00101-008-1 Screw, Hex Hd. 5/16-18x1.25, SHEF50 13216-001-5 Power Cord Assembly w/plug, 20' , 115V, SHEF50 00101-008-1 Screw, Hex Hd. 5/16-18x1.25, SHEF100 13216-004-5 Power Cord Assembly w/plug, 30' , 115V, SHEF50 13507-001-1 Leg, 2"...
  • Page 10 Pump Notes ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________...
  • Page 11 Pump Notes ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________...
  • Page 12 All dual seal non-clogs and 3–5 HP grinders must have seal failure and heat sensors attached and functional for Warranty to be in effect. If a seal failure should occur, Hydromatic will cover only the lower seal and labor thereof. Labor is based on Authorized Service Center contract allowance. If the heat sensor is not attached and functional, Warranty is void.

This manual is also suitable for:

Shef100

Table of Contents