Advertisement
Installation and Service Manual
SUBMERSIBLE
SOLIDS H NDLING PUMP
Models S4T, S8L, S8L , and S12L
NOTE! To the installer: Please make sure
you provide this manual to the owner of
the equipment or to the responsible party
who maintains the system.
For use with product
built with USEM motor.
10/10
Item # E-03-503
320 Frame
Part # 5625-503-1
© 2010 Pentair Pump Group, Inc.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hydromatic S4T Series
Summary of Contents for Hydromatic S4T Series
- Page 1 Installation and Service Manual SUBMERSIBLE SOLIDS H NDLING PUMP Models S4T, S8L, S8L , and S12L NOTE! To the installer: Please make sure you provide this manual to the owner of the equipment or to the responsible party who maintains the system. For use with product built with USEM motor.
-
Page 2: General Information
35 feet of power cord and/or possible septic sump. 35 feet of auxiliary control cord. Longer cable lengths can be Sump Level Control: furnished but must be specified at Sump level is controlled by time of order. Power cable is three Hydromatic float switch controls. -
Page 3: Installation Instructions
The Hydromatic NEMA 4 junction box is provided with compression connectors for sealing all wires. No sealing... -
Page 4: Pump Operations
In a duplex system the third or with an ohmmeter or Megger after Pump override control is usually set the connections are made. This is Operations about 6 inches above the one important, as one grounded wire pump turn-on control. can cause considerable trouble. -
Page 5: Pump Maintenance
The wires Pump an authorized Hydromatic service are potted in with sealing center. Charges will not be compound and a new unit Maintenance... - Page 6 Do not completely fill; leave side of shoulder of shaft sleeve oil about 1 inch below plug to remove. Seal should come IMPORTANT: Use only butt hole. Use only Hydromatic off with sleeve. If sleeve is not connectors on the wires. submersible this...
-
Page 7: Pump Troubleshooting
Pump will not start and liquid due to a failed level overload heaters trip. 2. Lower float control may be control. Hydromatic hung-up in the closed position. 1. Turn off power and check submersible motors Check in sump to be sure... - Page 8 Motor End Components...
- Page 9 Wet End Components S12L...
- Page 10 Motor End Parts List For use with product built with USEM motor. ORDERING REPLACEMENT PARTS: Product improvements are made from time to time. The latest part design will be furnished as long as it is interchangeable with the old part.When ordering replacement parts, always furnish the following information: (1) pump serial number, (2) pump model and size, (3) part description, (4) part number, (5) impeller diameter (if ordering impeller), (6) quantity required, and (7) shipping instructions.
- Page 11 Motor End Parts List For use with product built with USEM motor.
- Page 12 Cord Cap and Impeller Parts List For use with product built with USEM motor. Description HP Volt/Ph Cord Trim ITEM #1 ITEM #2 Description HP Volt/Ph Cord Trim ITEM #1 ITEM #2 Impeller Cord Cap Impeller Cord Cap 1750 RPM S4T12500M4-4 460/3 4/0-3...
- Page 13 Pump Notes...
-
Page 14: Standard Limited Warranty
12 months from the date of shipment from Hydromatic or 18 months from the manufacturing date, whichever occurs first - provided that such products are used compliance with the requirements of the Hydromatic catalog and technical manuals for use in pumping raw sewage, municipal wastewater or similar, abrasive free non-corrosive liquids. -
Page 16: Start-Up Report
Acknowledge that all information is accurate and proper procedures have been followed. Customer: ___________________________________________________________________ Date: _____________ Start-up Technician:___________________________________________________________ Date: _____________ Send to Warranty Manager, 1101 Myers Parkway, Ashland, OH 44805 or Fax to 419-207-3344 or email to startupreport@hydromatic.com or submit online at http://forms.pentairliterature.com/startupform/startupform.asp?type=h...
Need help?
Do you have a question about the S4T Series and is the answer not in the manual?
Questions and answers