Hydromatic S3SD Manual

Hydromatic S3SD Manual

Submersible sewage pump / dual seal pumps
Hide thumbs Also See for S3SD:

Advertisement

Quick Links

S3SD/S4SD &
SB3SD/SB4SD
Submersible Sewage Pump
Dual Seal Pumps
NOTE! To the installer: Please make sure you provide
this manual to the owner of the pumping equip ment or to
the responsible party who maintains the system.
Part # 5625-420-1
Item # E-03-420 04/09

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S3SD and is the answer not in the manual?

Questions and answers

Summary of Contents for Hydromatic S3SD

  • Page 1 S3SD/S4SD & SB3SD/SB4SD Submersible Sewage Pump Dual Seal Pumps NOTE! To the installer: Please make sure you provide this manual to the owner of the pumping equip ment or to the responsible party who maintains the system. Part # 5625-420-1...
  • Page 2: General Information

    It is recommended that the con cealed damage. Claims for Hydromatic 3900 mercury Hydromatic con trol panel be used damage must be made at the switch level controls. The 3900 with all pumps as proper start receiving end through the delivery...
  • Page 3: Pump Installation

    Installation Oth er wise water will re turn to the Overload Heaters: sump and cause short cycling of If a Hydromatic control pan el is the pump. installing Pump in Sump: not used, on three phase pumps all three phases must have overload...
  • Page 4: Pump Operations

    If an alarm system is used, this Pump Pump con trol is usually set about 6 inch es Installation Operations above the over ride control. Some engineers as de scribed pre vi ous ly prefer to have the Wiring diagrams are pro vid ed Starting System: alarm control set be low the with pan el for making con nec-...
  • Page 5: Pump Maintenance

    5. Allow sump level to rise to Hydromatic service cen ter. start oth er pump. Notice run As the motors are oil filled, no lights on panel; pumps should...
  • Page 6 10.After all leads are reconnected, make a high voltage ground test on each wire. The only wire that should show ground is the green power lead. 11.Refill motor chamber with oil. Use only high grade trans form- er oil or reg u lar Hydromatic...
  • Page 7: Pump Troubleshooting

    Pump runs but will not shut off: 4. Discharge head may be too Pump high. Check total head with 1. Pump may be air locked. Troubleshooting gauge when pump is op er at ing. Turn pump off and let set for Total head is dis charge gauge several min utes, then restart.
  • Page 8: Parts List

    S3SD Parts List ORDERINg REPLACEMENT PARTS: Product improvements are made from time to time. The latest part design will be fur- nished as long as it is in ter change able with the old part.When ordering re place ment parts, always furnish the fol low ing information: (1) pump serial num ber, (2) pump model and size, (3) part description, (4) part number, (5) im pel ler diameter (if ordering impeller), (6) quan ti ty required, and (7) shipping instructions.
  • Page 9 S3SD...
  • Page 10 SB3SD Parts List ORDERING REPLACEMENT PARTS: Product improvements are made from time to time. The latest part design will be fur- nished as long as it is in ter change able with the old part.When ordering re place ment parts, always furnish the fol low ing information: (1) pump serial num ber, (2) pump model and size, (3) part description, (4) part number, (5) im pel ler diameter (if ordering impeller), (6) quan ti ty required, and (7) shipping instructions.
  • Page 11 SB3SD 39, 41 14 15...
  • Page 12 S4SD Parts List ORDERINg REPLACEMENT PARTS: Product improvements are made from time to time. The latest part design will be fur- nished as long as it is in ter change able with the old part.When ordering re place ment parts, always furnish the fol low ing information: (1) pump serial num ber, (2) pump model and size, (3) part description, (4) part number, (5) im pel ler diameter (if ordering impeller), (6) quan ti ty required, and (7) shipping instructions.
  • Page 13 S4SD...
  • Page 14 SB4SD Parts List ORDERINg REPLACEMENT PARTS: Product improvements are made from time to time. The latest part design will be fur- nished as long as it is in ter change able with the old part.When ordering re place ment parts, always furnish the fol low ing information: (1) pump serial num ber, (2) pump model and size, (3) part description, (4) part number, (5) im pel ler diameter (if ordering impeller), (6) quan ti ty required, and (7) shipping instructions.
  • Page 15 SB4SD 39, 41 14 15...
  • Page 16 Pump Notes ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________...
  • Page 17 Pump Notes ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________ ______________________________________________...
  • Page 18: Standard Limited Warranty

    12 months ® from the date of shipment from Hydromatic or 18 months from the manufacturing date, whichever occurs first - provided that such products are used compliance with the requirements of the Hydromatic catalog and technical manuals for use in pumping raw sewage, municipal wastewater or similar, abrasive free non-corrosive liquids.
  • Page 20: Start-Up Report

    Acknowledge that all information is accurate and proper procedures have been followed: Customer Signature:__________________________________________________ Date ___________ Start-up Technician:__________________________________________________ Date __________ Send to: Warranty Department, 740 E. Ninth Street, Ashland, OH 44805, Fax: 419-207-3344, or e-mail to: startupreport@hydromatic.com We will make this a permanent part of our file on this order.

This manual is also suitable for:

S4sdSb3sdSb4sd

Table of Contents