biodex 840-000 Installation Instructions Manual

biodex 840-000 Installation Instructions Manual

Multi-joint system
Hide thumbs Also See for 840-000:

Advertisement

BIODEX MULTI-JOINT SYSTEM
INSTALLATION INSTRUCTIONS
840-000
840-000-10
840-000-30
850-000
850-000-10
850-000-30
FN: 08-051-CLR Rev A 9/19

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 840-000 and is the answer not in the manual?

Questions and answers

Summary of Contents for biodex 840-000

  • Page 1 BIODEX MULTI-JOINT SYSTEM INSTALLATION INSTRUCTIONS 840-000 840-000-10 840-000-30 850-000 850-000-10 850-000-30 FN: 08-051-CLR Rev A 9/19...
  • Page 2 Additional information and resources, including installation instructions, are available upon request or directly from the Biodex website, http://www.biodex.com. If the desired information is not found, please feel free to contact a local distributor or Biodex directly at supportservices@biodex.com. Thank you, Biodex Medical Systems, Inc.
  • Page 3: Table Of Contents

    Table of Contents   Definition of Symbols ........................ 4     Installation Instructions ....................... 6   Tools Required ......................6   Installation Procedure ....................6   Monitor Install Procedure ....................8   Cabling for CDS Power Receptacle ................. 8   Seat Lift Power Connection ..................
  • Page 4: Definition Of Symbols

    Definition of Symbols The following symbols and their associated definitions are used and implied throughout this manual.
  • Page 5 Site Requirements Electrical Specifications System Power Requirements: Provide 220 VAC/60 Hz 20 amp dedicated electrical service with dedicated ground. Locate within ten feet of ear of the T-base. Receptacle will be a single Hubbell #IG-5461, rated for 250 VAC, or hospital grade equivalent.
  • Page 6: Installation Instructions

    1. Installation Instructions Tools Required 1. Allen wrench set, 1/8" 5/16" 2. Socket set with extension, 1/2", 9/16", 7/1", 3/4", 5/8" 3. Open end or closed end wrench, 1/2", 9/16", 7/1", 3/4", 5/8" 4. Flat head and Phillips head screwdriver 5.
  • Page 7 Figure 1.1. Multi-Joint System Cart and Monitor from the Rear...
  • Page 8: Monitor Install Procedure

    Monitor Install Procedure Figure 1.2. Rear View of the CDS Cart Cabling for CDS Power Receptacle CDS Cart Power Seat Lift Power 195 to 245 Volt AC Receptacle Receptacle Input Receptacle Figure 1.3. Power Receptacles on the Back of Seat.
  • Page 9 Figure 1.4. Remove Screws from the CDS Cart Power Receptacle. Figure 1.5. Loosen the Clamp on the Cable. Strain Relief Slot Facing Up Cable Clamp Strain Relief Screw Facing Left Figure 1.6. Cable Positioned at CDS Cart Power Receptacle.
  • Page 10: Seat Lift Power Connection

    Figure 1.7. Attaching Cable to CDS Cart Power Receptacle. Seat Lift Power Connection Cable Clamp Screw Figure 1.8. Loosen the Cable Clamp Screw and Replace the Clamp on the Cable. Seat Lift Receptacle Strain Relief Cable Clamp Screw Figure 1.9. Seat Lift Receptacle.
  • Page 11: Ac Input Receptacle Power Connection

    Seat Lift Power Cord Cable Clamp Screw Cable Strain Relief Figure 1.10. Installing the Seat Lift Power Cord. AC Input Receptacle Power Connection Figure 1.11. Loosen the Clamp on the Cable. Figure 1.12. Loosen the Cable Clamp Screw and Remove the Strain Relief.
  • Page 12 Cable Clamp Screw Figure 1.13. Removing the Screws from the AC Input Receptacle. Figure 1.14. Installing the AC Input Cable.
  • Page 13: Installation Report

    Date of Installation: Site Information: (Print clearly or type) FACILITY: ADDRESS: CITY, STATE: CONTACT AT SITE: PHONE: ( FAX: ( Biodex Representative: Installation Start Time: Serial Number: Model Number: Software Version: Firmware Version: Biodex Contacts: 1-800-224-6339 Software Support-ext. 2120 Technical Support-ext. 2116 Technical and Software Support-ext.
  • Page 14 System Site Checkout 1. Unpack and assemble system. Check for physical damage or cosmetic defects. Comments: 2. In "setup" use knee accessory and set the range limits maximum (total ROM- degrees is between 149-152). Comments: 3. While in "Passive" mode, test percent ROM controls, cushion and the pause controls.
  • Page 15 Description Customer request/comments: With the exception of any items listed above, the Biodex System has been completely installed satisfactorily and is functioning properly. The Biodex representative has instructed the facility on startup, hardware and software. The facility is capable of proper operation of the Biodex System.

This manual is also suitable for:

840-000-10840-000-30850-000-30850-000850-000-10

Table of Contents