Table of Contents
Advertisement
Quick Links
E-964-Q660Q –
E-964-Q495Q –
E-964-Q330Q –
E-964-Q165Q –
SECO-LARM
MANUAL
Multi-Frequency
Quad Photobeam Detectors
660 ft. (200m) outdoors, 1320 ft. (400m) indoors
495 ft. (150m) outdoors, 990 ft. (300m) indoors
330 ft. (100m) outdoors, 660 ft. (200m) indoors
165 ft. ( 50m) outdoors, 330 ft. (100m) indoors
®
Advertisement
Table of Contents
Related Manuals for SECO-LARM ENFORCER E-964-Q660Q
Summary of Contents for SECO-LARM ENFORCER E-964-Q660Q
- Page 1 660 ft. (200m) outdoors, 1320 ft. (400m) indoors E-964-Q495Q – 495 ft. (150m) outdoors, 990 ft. (300m) indoors E-964-Q330Q – 330 ft. (100m) outdoors, 660 ft. (200m) indoors E-964-Q165Q – 165 ft. ( 50m) outdoors, 330 ft. (100m) indoors SECO-LARM ®...
-
Page 2: Table Of Contents
● alignment. Signal is sent if a degradation in environmental conditions is detected such as thickening fog to Input voltage: 12-24V AC/DC. ● prevent false alarms. Response time adjustable for nearly all ● Built-in heater. situations. ● ® SECO-LARM U.S.A. -
Page 3: Overview
Horizontal Alignment laser adjustment grip (Receiver shown) Viewfinder for alignment On/Off switch for laser IMPORTANT – Do not connect to power until the sensor is completely installed and the installation has been double-checked. Factory default 50ms ® SECO-LARM U.S.A. -
Page 4: Wiring Diagram
310m 2,600m 5,200m AWG17 3,190ft. 28,870ft. 2,790ft. 24,930ft. 1,940ft. 17,060ft. 1,020ft. 8,530ft. Note (1): Max. cable length when two or more sets are connected is the value shown in Table 1 divided by the no. of sets. ® SECO-LARM U.S.A. -
Page 5: Multiple Sensor Sample Applications
1 2 3 4 1 2 3 1 2 3 1 2 3 4 1 2 3 Views 1 2 1 2 1 2 1 2 1 2 1 2 ® SECO-LARM U.S.A. -
Page 6: Wiring The Transmitter - Wall Mount
1. Screw the wires tightly to avoid slipping off the terminals, but not so tight that they break. 2. Screws on terminals which are not used should be tightened. 3. Grounding may be necessary, depending on the location. SECO-LARM ® U.S.A. -
Page 7: Examples Of Ways To Connect Sensors
(ch. 2) ➀➁ ➀➁ ➀ ➁ ➂ ➃ ➀ ➁ ➂ ➃ Control panel (12~24VAC/VDC) Example connection 4 - Two stacked Power Alarm signal ➀➁ ➀ ➁ ➂ ➃ Control panel (12~24VAC/VDC) ➀ ➁ ➂ ➃ ➀➁ SECO-LARM ® U.S.A. -
Page 8: Selectable 4-Channel Beam Frequency
Fig. 9: Receiver Detail DIP Switch Channel Selector Beam Alignment Buzzer Switch Beam Alignment Strength Indicator Switch Response Time Adjustment Fig. 10: Included Beam Alignment Template: Use the included SECO-LARM template to aid in aligning the transmitter and receiver. ® SECO-LARM U.S.A. -
Page 9: Beam Alignment
3. Using Table 3, adjust the receiver’s sensors vertically and horizontally until the best possible voltage output is achieved. Table. 3: Voltage Output Voltage Output <1.1V 1.1~1.4V 1.4~1.7V 1.7~2.0V >2.0V Alignment Quality No Signal Poor Good Strongest ® SECO-LARM U.S.A. -
Page 10: Adjusting The Response Time
* This is the minimum time interval between breaking of both beams which will trigger the output. Setting the interval longer will reduce false alarms from birds or falling leaves, etc., while setting it shorter will detect faster moving objects. ® SECO-LARM U.S.A. -
Page 11: Dimensions
Clean the lenses of both units. _________________________________________________________________________________________________________________________________ Alarm trigger becomes erratic in bad weather Check overall system installation. Realign the lenses. _________________________________________________________________________________________________________________________________ Frequent false alarm triggers Adjust the response time. Change location of transmitter and receiver. ® SECO-LARM U.S.A. - Page 12 SECO-LARM policy is one of continual development and improvement. For that reason, SECOLARM reserves the right to change specifications without notice. SECOLARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2019 SECOLARM U.S.A., Inc. All rights reserved.