Starline A63 ECO Manual
  1. Manuals
  2. Brands
  3. Starline Manuals
  4. Car Alarm
  5. A63 ECO
  6. Manual

Starline A63 ECO Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Thank you for your choice
StarLine security-telematic complex
and wish you safe travels!
The information presented in this manual,
refers to car alarms StarLine
A63 eco, А63, A93 eco,
A93, A93 GSM, А93 2CAN+2LIN
Software
GK74-Р3
Federal StarLine Technical Support. Free call
Russia
Kazakhstan
Ukraine
Belarus
8-800-333-80-30
8-800-070-80-30
0-800-502-308
8-10-8000-333-80-30
Edition №5
March 2017 г.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the A63 ECO and is the answer not in the manual?

Questions and answers

Related Manuals for Starline A63 ECO

Summary of Contents for Starline A63 ECO

  • Page 1 Thank you for your choice StarLine security-telematic complex and wish you safe travels! The information presented in this manual, refers to car alarms StarLine A63 eco, А63, A93 eco, A93, A93 GSM, А93 2CAN+2LIN Software GK74-Р3 Federal StarLine Technical Support. Free call...
  • Page 2 StarLine A93, StarLine A63 Please read carefully! Before embarked on the exploitation the car alarm, read this manual carefully, pay attention to all sections marked with , and decide if this car alarm is the right for your car, for which follow the requirements of the car’s manufacturer and car’s service manual.
  • Page 3 User’s manual In order to avoid possible misunderstandings, please keep documents attached to the car alarm in the sale. Check the filling in the warranty card, including availability of the date of the sale and stamp of the seller. In the absence of the date of the sale (purchase) the warranty period starts since the date of manufacture of the car alarm.
  • Page 4 StarLine A93, StarLine A63 Before embarked on the exploitation the car alarm, carefully read the precautions of the safe use of remote or automatic engine starting set out below: 1. Always park out the car on an open, well-ventilated site;...
  • Page 5 User’s manual Mandatory safety measures during charging car’s battery Remember that any process of battery charge associated with the supply on the battery and, accordingly, in the onboard network of the vehicle electrical voltage greater than the nominal 12V, which will damage the equipment of the vehicle and equipment additionally installed on your car.
  • Page 6 StarLine A93, StarLine A63 Connection and disconnection completely discharged or faulty battery on your car while engine is running can destroy electronic devices of your car and car alarm due short circuit or surge overvoltage occurring when connecting/disconnecting the battery.

  • Page 7: Table Of Contents

    LCD display of alarm reasons ..................48 Protection against power disconnection ..............49 Additional wireless lock radio relays StarLine R2 ..........49 Additional code relays StarLine R3 and StarLine R4 ........... 50 Connection of GSM modules ..................50 Anti-hijack mode ......................50...
  • Page 8 StarLine A93, StarLine A63 Activation of anti-hijack mode by remote ............. 51 How to switch anti-hijack off ..................53 PANIC function ......................... 54 Service functions Car status check, car battery voltage, passenger compartment and engine temperatures ........... 55 Automatic door lock control ..................56 Car finder ...........................
  • Page 9 User’s manual Remote engine start Particular features of remote engine start .............. 91 Prepare for remote engine start for cars with manual transmission ..... 92 Procedure «sofware neutral» ..................92 Remote engine start by remote control ..............96 Remote engine shut down ................... 97 Remote prolongation of engine running time ............

  • Page 10: Technical Specification

    StarLine A93, StarLine A63 Technical specification RF carrying frequency ........... from 433,05 to 434,79 MHz RF channels ......................128 LCD remote range: Control commands ..................800 m* Alarm trigger reception ................2000 m* LED remote range ....................15 m* Shock/tilt sensor type .......... 3 axis digital accelerometer Working temp range ............

  • Page 11: Security And Service Functions Of Car Alarm

    Protected areas of the car and how to control them • Engine – a blocking relay, code relay StarLine R3 (optional), and StarLine R4 (optional), digital radio relay StarLine R2 (optional). • The doors, hood, trunk, hand brake, the brake pedal –...
  • Page 12 StarLine A93, StarLine A63 • Engine blocking preserved even after HW removal • Programmable 2 steps engine unblock. Self-diagnosis and indication of operating modes • Indication of a faulty zone when arming. • Display the reason of car alarm trigger, for 11 zones of protection.
  • Page 13 • Display of the current time, alarm, reverse timer. • Indication of remote control battery discharge. • Support external GSM modules StarLine M20, M30 and StarLine M21, M22, M31, M32 or installation of built-in GSM module Remote engine start functions •...

  • Page 14: How To Control Car Alarm

    StarLine A93, StarLine A63 How to control Car alarm Remotes for control Car alarm has the following remotes included in kit*: LCD remote control: LED remote control: 4-buttons remote control with 3-buttons remote control 2 -way control and without display LCD display.

  • Page 15: Duration Of Buttons Pressing Of Remote Controls

    User’s manual Duration of buttons pressing of remote controls Here and further in text we use the following terminology of duration and sequence of remote control pressing: •  Short press — one time button press (or 2 buttons together) duration is less 0,5 s; • ...

  • Page 16: Remote Control Commands

    StarLine A93, StarLine A63 Remote control commands PRESS BUTTONS CONDITION COMMAND Ignition Icons remote remote Security functions Any except ARM with sound short Any except DISARM with sound short Any except ARM without 1 + 1 sound in sequence double...
  • Page 17 User’s manual PRESS BUTTONS CONDITION COMMAND Ignition Icons remote remote Hi-Jack mode Any except No matter No matter short 2 + 1 Any except Shock sensor Levels ON/OFF double sequence Tilt sensor – No matter Levels ON/OFF double 1 + 3 1 + 2 Any except PANIC mode ON...
  • Page 18 StarLine A93, StarLine A63 Additional equipment control 2 + 1 CH 1 activation No matter No matter No matter In sequence double 3 + 2 3 + 1 CH 2 activation No matter No matter No matter In sequence sequence...
  • Page 19 User’s manual Service functions Car alarm status request car battery voltage, – No matter No matter No matter short engine and passenger compartment temp Car find No matter No matter No matter double short 2 or 3 Long until Activation of second –...

  • Page 20: Lcd Display

    StarLine A93, StarLine A63 LCD display Active modes and functions Turbotimer mode*. Timer engine start mode.* Alarm clock engine start mode.* Temperature engine start mode*. Service mode. Keychain silent mode. Buttons press block. *engine start modules should be installed (check with your installer)

  • Page 21: Car Alarm Status Indication

    Hand brake is not tighten (or pedal brake is pressed). Engine is running Battery discharged Car interior temperature Engine temperature any StarLine GSM is connected The stand-alone heater is on. Tilt sensor trigger. Shock sensor light trigger Shock sensor heavy trigger...

  • Page 22: Lcd Remote Main Functions Menu

    StarLine A93, StarLine A63 LCD remote main functions menu Remote control main menu: • set current time; • set alarm clock time; • alarm clock ON/OFF; • set timer time; • switch timer ON/OFF; • select volume of alarm trigger signal or scilent mode ;...
  • Page 23 User’s manual Short press button 4 to start setting Hours of alarm clock: remote Alarm clock hours flashing; button 2 —increase setting, button 3 —decrease setting. Short press button 4 to start setting Minutes of alarm clock: remote Alarm clock minutes flashing; button 2 —increase setting, button 3 —decrease setting Short press button 4 to start setting...
  • Page 24 StarLine A93, StarLine A63 Short press button 4 to start setting Timer hours: remote Timer hours are flashing: button 2 - increase setting, button 3 - decrease setting Short press button 4 to start setting Timer minutes : remote Timer minutes are flashing: button 2 —increase setting,...
  • Page 25 User’s manual Short press button 4 to start setting volume of alarm trigger signals or switch ON silent mode remote Siren icon flash: button 2 — select volume of remote control signals: — high volume, — low volume button 3 — switch ON silent mode: —...

  • Page 26: Working Modes Setting By Cursor Method

    StarLine A93, StarLine A63 Working modes setting by cursor method Some car alarm modes possible to switch on by using cursor method. ON status of any mode is confirmed by backlight of corresponding icon. This programming available during armed or disarmed status.
  • Page 27 User’s manual To switch ON selected mode 3а press button 1: remote • 1 melody and 2 short • 1 light flash beeps; • After exit setting mode selected icon will be highlighted constantly (mode is ON). To switch selected mode OFF 3б...

  • Page 28: List Of Modes, Possible To Set By Cursor Method

    StarLine A93, StarLine A63 List of modes, possible to set by cursor method Alarm clock engine start. One time engine start corresponding alarm clock Set time (see page 94) Timer engine start. Auto engine start every 2 to 24 hours, step 2hours See page 95) Temperature engine start.

  • Page 29: Security Functions

    User’s manual Security functions ARM with sound confirmation Before arming, be sure that: • ignition is OFF; • hand brake ON; • door, hood, trunk are closed. Press button 1: remote • 1 beep; • 1 siren signal; • LCD panel •...

  • Page 30: Arm Without Sound Confirmation

    StarLine A93, StarLine A63 ARM without sound confirmation Before arming, be sure that: • ignition is OFF; • hand brake ON; • door, hood, trunk are closed. Press button 1 at first long (until sound appear), then short: remote • 1 light flash;...

  • Page 31: Silent Arm Mode

    User’s manual Silent arm mode In silent arm mode if any alarm trigger happens siren signals will be absent. Alarm trigger condition is confirmed only by light flashing. Press button 1 at first long (until sound appear), then button 2 short: remote •...

  • Page 32: Passive Arming

    StarLine A93, StarLine A63 Passive arming The mode is programmed. We recommend that you contact the car alarm installers. Default mode is OFF. Switch ignition OFF, leave the car and close all doors • 1 siren signal; 1 light flash.

  • Page 33: Arm Mode With Engine Running

    User’s manual ARM mode with engine running* Before arming please be sure: • car transmission is in neutral position (or in PARK position for auto transmission); • hood closed, engine is running. Tight hand brake, open Door and press button 2: remote •...
  • Page 34 3 light signal of the car. Time of engine running will increase each time for 5 minutes. For StarLine A63 and StarLine A63 ECO must be connected support relay plugs (see instructions manual). Refer to the car alarms installers.

  • Page 35: Remote Engine Shut Down With Keeping Arm Mode

    User’s manual Remote engine shut down With keeping ARM mode Press button 1 long (untill Melody appear), then press 4 short remote • 3 light flashes • Melody plays; • Ignition and shock • Indication of sensor detection will engine run will be ON;...

  • Page 36: Arm Without Remote Control

    StarLine A93, StarLine A63 Arm without remote control Before arming be sure that: • ignition is OFF, • hand brake is activated. Open any door and switch ignition ON Press service button 3 times and switch ignition OFF: • 1 siren signal, 1 light flash;...

  • Page 37: Auto Rearming

    User’s manual Auto rearming If auto rearming is programmed (function 5, table №1) and during 30 sec doors are not opened System will be armed automatically. Attention! Doors will be locked in case, of rearmed function is programmed with option to lock doors (function 5, table №1). Rearm will be confirmed by 1 siren signal and 1 light flash.

  • Page 38: Self-Diagnostic During Arming

    StarLine A93, StarLine A63 Self diagnostic during arming During arming system automatically checks all input zones. • Door, hood or trunk are not properly closed; • Any limit switch failed (constantly closed) of door, hood or trunk. ARM by pressing button 1: remote •...

  • Page 39: Disarm With Audio Confirmation Signals

    User’s manual In case of failed situation will be restored automatically protection zone will be returned in active status DISARM with audio confirmation signals Press button 2: remote • 2 siren signals; • 2 beeps; • 2 light flashes • Indication of •...

  • Page 40: Disarm Without Audio Confirmation Signals

    StarLine A93, StarLine A63 DISARM without audio confirmation signals Press button 2 at first long (until melody appear) and then short: remote • 2 light flashes • 2 beeps; • LED is OFF • Indication of • Doors unlocked disarmed mode will appear.

  • Page 41: Two-Step Unlock Engine

    User’s manual Two-step unlock engine The function is programmed (Default mode is OFF). If this function is enabled, the engine will remain locked after each deactivation of the alarm. To unblock engine after disarming please enter PIN-code (see page 82). •...

  • Page 42: Disarm Without Remote Control

    StarLine A93, StarLine A63 Disarm without remote control Open car door by key: • Alarm trigger signals start (in case when it was armed by remote control); • Follow 4 light flashes (in case when it was armed without remote control).

  • Page 43: Disarm With Engine Running

    User’s manual Disarm with engine running Disarm by pressing button 2. Enter the car and switch ignition ON by key: remote • Engine continue to run • Appear indication of engine running and disarmed mode. Release hand brake off: remote •...

  • Page 44: Selfdiagnostic During Disarming

    StarLine A93, StarLine A63 Selfdiagnostic during disarming During disarming system will inform you about missed alarm events. Disarm by pressing button 2 • If alarm signals were interrupted by remote: remote • 2 siren • 2 beeps; signals • If the reason of triggering •...

  • Page 45: Alarm Signals Interrupted Without Disarming

    User’s manual Alarm signals interrupt without disarming remote • Alarm signals • Alarm melody plays; • LCD shows the reason of alarm. Press button 1: remote • Alarm melody • Alarm signals will stop; stops; • Corresponding zone • LCD shows the will be temporarily reason of alarm;...

  • Page 46: Alarm Signals

    StarLine A93, StarLine A63 Alarm signals If triggered automatically appeares alarm signals. Alarm signals – signals of siren and light flashes. Remote control also start to produce alarm melody, LCD will show the reason of alarm During alarm melody icons depending on reason of alarm will start to flash.
  • Page 47 User’s manual 30 s of sound Ignition no limit no limit and light signals 30 s of sound Brakes no limit and light signals 1) During car light flashing, car head light on LCD picture also will flash. 2) In case when reason of alarm is not removed (for example, doors continued to be opened ) corresponding input is temporarily bypassed until the reason of alarm dissapeared (for example, door closed) LCD continue to show the reason of alarm...

  • Page 48: Lcd Display Of Alarm Reasons

    StarLine A93, StarLine A63 LCD display of alarm reasons • Heavy level of shock sensor • Light level of shock sensor • Hand brake off • Ignition was ON • Tilt sensor • Door opened • Trunk opened • Hood opened...

  • Page 49: Protection Against Power Disconnection

    Additional wireless lock radio relays StarLine R2 Using the digital radio relay for engine blocking StarLine R2 can significantly increase the anti-hijack function of the car alarm due to hidden installation of the relay in the staff wiring of the car and the absence of any wired connections between the central unit of the car alarm and blocking radio relay.

  • Page 50: Additional Code Relays Starline R3 And Starline R4

    Connection of GSM modules If necessary, you can connect to your car alarm one of the additional GSM modules StarLine M20, M30, M21, M22, M31, M32 or built-in GSM. The use of GSM module enables you to manage car alarm, receive messages the invasion of the car to determine location car with virtually no range limit - wherever there GSM network.
  • Page 51 User’s manual Hidden method of switching anti-hijack on Hidden anti-hijack switch mode can be applied in a situation where other methods difficult or impossible. Enabling occurs when you open the door (for example, if the owner is forced to leave the car), after which the car alarm operates automatically on a certain algorithm, consisting of several steps.
  • Page 52 StarLine A93, StarLine A63 Step 4: 30 s after intermittent alarm signal appear • Constant alarm signals start; • Intermittent engine blocking will start immediatelly or after pressing pedal brake (depending on function 8 settings , table. №1); • Light flashes continue.

  • Page 53: How To Switch Anti-Hijack Off

    User’s manual How to switch anti-hijack off Open car door and input PIN-code (see page. 82). After last digit input and ignition is switched ON remote • 2 siren signals; • 2 beeps • 2 light flashes; • Doors unlocked; •...

  • Page 54: Panic Function

    StarLine A93, StarLine A63 PANIC function When the panic mode is activated, light and audible alarms are activated for 15 seconds. If the guard was turned off, the armed mode is activated. While ignition is ON press and hold buttons 1 and 3 : remote •...

  • Page 55: Service Functions Car Status Check, Car Battery Voltage

    User’s manual Service functions Car status check, Car battery voltage, passenger compartment and engine temperatures* This command could be used in any mode for car status check, car battery voltage check temperature in passenger compartment and engine temperatures. Press button 3 short: remote •...

  • Page 56: Automatic Door Lock Control

    StarLine A93, StarLine A63 Interior temperature sensor is located in a car alarm main unit. Therefore, the temperature displayed on the remote LCD can differ from the actual temperature in the cabin as this depending on the unit installation place. The displayed...

  • Page 57: Car Finder

    User’s manual Version 1: – auto lock control is disabled. doors Version 2: – locked 10 s after ignition is turned ON; – unlocked after ignition turned off. Version 3: doors – locked 10 s after ignition is turned ON. Version 4: doors –...

  • Page 58: Temporarily Shock Sensor Bypass

    StarLine A93, StarLine A63 Temporarily shock sensor bypass In armed mode press two times shortly button 1 брелка. Light level of shock sensor, will be bypassed: remote • Melody plays • 2 light flash • Appear indication of • Light level of...

  • Page 59: Temporarily Tilt Sensor Bypass

    User’s manual Temporarily tilt sensor bypass In armed mode press two times shortly press button 3. Tilt sensor will be disabled: remote • 3 light flashes. • 3 beeps; • Appear indication of tilt sensor bypassed In armed mode press two times shortly press button 3.

  • Page 60: Tilt Sensor Sensitivity Adjustment

    StarLine A93, StarLine A63 Tilt sensor sensitivity adjustment The maximum sensitivity of the tilt sensor corresponds to value of 14, the minimum is 01. When you select the value 0, the sensor is deactivated (factory setting - 10). In disarmed mode and ignition...

  • Page 61: Shock Sensor Sensitivity Adjustment

    User’s manual Shock sensor sensitivity adjustment In disarmed mode and ignition is off press button 3 at first long (until melody appear), then short: remote • 3 light • Melody plays; • Appear indication of flashes; • 2 siren sensitivity level for light signals.
  • Page 62 StarLine A93, StarLine A63 By short press of buttons 2 and 3 set desired sensitivity. To exit sensitivity adjustment mode press button 3 at first long (until melody appear), then short: remote • 3 light flashes • Melody plays. • 2 siren signals...

  • Page 63: Additional Ch 1 Control

    User’s manual Additional CH 1 control Versions of CH activation are defined by function 13 table №1 (see page 112). Command by remote is following: Press button 2 long, Then button 1 short: remote • 3 beeps. • 3 light flashes. Version 1: Trunk release •...
  • Page 64 StarLine A93, StarLine A63 After luggage put/taken out close the trunk • In case of armed: remote • 1 beep • Trunk and shock • Indication of sensor will be opened trunk will enabled after 5 s. dissapear Shock sensor bypass...

  • Page 65: Additional Ch 2 Control

    User’s manual version 4: «latch» mode. In the «latch» mode channel output is controled by remote Control. The output status is changed to opposite after every activation. Type of additional equipment connected to the channel №1, is specified during the installation of car alarm. Additional CH 2 control Versions of CH activation are defined by function 14 table №1 (see page 112).
  • Page 66 StarLine A93, StarLine A63 In order to implement the two-step unlocking, door activator of the driver’s door and other doors activators should be connected in accordance with the scheme two-step unlocking. See installation instructions. Version 2: FLEX programming. For this version, an activation method (by remote control or automatically upon event happens) duration and the delay of the output signal can be programmed.

  • Page 67: Additional Ch 3 Control

    User’s manual Type of additional equipment connected to the channel №1, is specified during the installation of car alarm. Additional CH 3 control Versions of CH 3 activation are defined by function 15 table №1 (see page 112). Activation happens automatically. For details see installation manual.

  • Page 68: Additional Ch 5 Control

    StarLine A93, StarLine A63 Type of additional equipment connected to the channels №3, is specified during the installation of car alarm. Additional CH 5 control Versions of CH 5 activation are defined by function 19 table №1 (see page 112)

  • Page 69: Additional Ch 6 Control

    (see installation manual). Version 4: Webasto control via digital bus. For information on setting up and connecting a stand-alone heater to the StarLine system, see the installation www.starline.ru. instructions on Type of additional equipment connected to the channels №6, is specified during the installation of car alarm.

  • Page 70: Additional Ch 7 Control (Locking Relay, Connector X1)

    StarLine A93, StarLine A63 Additional CH 7 control (locking relay, connector Х1) Versions of CH 7 activation are defined by function 24 table №1 (see page 113) Channel activates automatically Version 1: Central lock control «LOCK» This version is intended for power central lock control. Schematic see installation manual.

  • Page 71: Additional Ch 8 Control (Unlocking Relay, Connector X1)

    Х3 connector Variants 3 and 4 are necessary for the implementation of the engine start-up functions, for details, see the installation www.starline.ru instructions at Type of additional equipment connected to the сhannels №8, is specified during the installation of car alarm.

  • Page 72: Additional Ch 9 Control

    StarLine A93, StarLine A63 Additional CH 9 control (light signals control relay, connector Х2) Versions of CH 9 activation are defined by function 24 table №1 (see page 113) Channel activates automatically Version 1: light signals control This version is intended for power control of light signals. Schematic see installation manual.

  • Page 73: Turbotimer Mode

    To use this function in the complex should be realized the connection of the engine start-up circuit (refer a car alarm installers), and function 12 table №2 (see the installation instructions at www.starline.ru) must be programmed for one of the versions of ignition support. Activation of turbotimer mode and setting...
  • Page 74 StarLine A93, StarLine A63 By short press button 1 select TT duration time remote Every press increase duration for 1 min Press button 1 long (until sound appear). Or wait for auto exit (after 4 s.) and save of selected...
  • Page 75 User’s manual Activation of turbotimer Be sure that: • gear is in neutral position (or in «PARK» position for auto transmission); • Doors and hood are closed; • engine is running. Depending on ignition support version (that is selected by installer) turbotimer could be activated in the following way: By BREAK ACTIVATION : - put hand brake in ON:;...
  • Page 76 StarLine A93, StarLine A63 • If you have manual transmission selected by programming: remote • LED constantly ON • 1 melody play; • LCD will show r06 - time, after it engine will be shut down, if no arming earlier...
  • Page 77 User’s manual If you need to arm, remove ignition key get out of car, lock all the doors and arm system by one of mentioned methods (see page 29-31): remote • 1 beep; • 1 siren signal • Appear • 1 light flash indication •...

  • Page 78: Serviceability Control Of Limit Switches

    StarLine A93, StarLine A63 Serviceability control of limit switches StarLine A93, A63 provides the ability to control serviceability of doors, hood and trunk limit switches when the system is disarmed. Opening doors, hood and trunk while ignition is ON must be accompanied by periodic flashes the LED.

  • Page 79: Lcd Remote Battery Charge Check

    User’s manual LCD remote battery charge check Check of battery charge is made at every any button been pressed remote • When battery is discharge LCD will show icon • Please replace the battery CALL from car To call from car to remote control press and hold more than 3s button of transciever plastic case: remote •...

  • Page 80: Alarm Memory

    StarLine A93, StarLine A63 Alarm memory In case of an alarm trigger happens, information about sensor, the date and time is kept in memory of car alarm. Up to 8 last events can be stored in the memory of the car alarm.
  • Page 81 User’s manual press button 4: press button 3: • alarm №1 (door open): press button 4: press button 3: • alarm №2: (hood open): press button 4: press button 3: • alarm №8: (shock sensor):...

  • Page 82: Out Of Range Check

    StarLine A93, StarLine A63 Out of range check If auto range check is selected every 3, 5 or 7 minutes communication between car and remote control will be checked. remote • If you are out of range remote control will beep once and flash lower part of the sphere Range check is available only in armed mode.

  • Page 83: Buttons Block From Pressing

    User’s manual Buttons block from pressing Shortly press both buttons 2 and 4 : remote • 1 short beep; • Appear icon • Buttons are blocked. To release buttons blocking, shortly press both buttons 1 and 4 remote • Melody plays; •...

  • Page 84: Engine Heater Control

    StarLine A93, StarLine A63 Engine heater control If engine heater is connected to your car alarm (for example Webasto), you could control it by remote control. Press button 1 long (until melody appear), then press button 3 shortly: remote • Appear icon •...

  • Page 85: Remote Controls Learning

    User’s manual Remote controls learning Learning remote controls should be made in disarmed mode in the following way: Press valet button 7 times and switch ignition ON: • Follow 7 siren signals, confirming entry in learning mode; Press shortly both buttons 1 and 2 : remote •...

  • Page 86: Check The Quantity Of Learned Remote Controls

    StarLine A93, StarLine A63 Attention! When learning remote controls all previously learned remotes are deleted from memory, so all the desired remote controls should be learned again in the same cycle of programming (see item 2). Totaly you could learn up to 4 remote controls.
  • Page 87 User’s manual PIN code input - version 1 (emergency disarm) Open the door and keep opened: • Start alarm signals (if was armed by remote control), • 4 light flashes (if was armed without remote control), INPUT 1 DIGIT. Switch ignition ON. Press service button same time like first PIN code digit switch ignition OFF: •...
  • Page 88 StarLine A93, StarLine A63 PIN code input - version 2 (emergency disarm) This version is more convinient for cars with start/stop push buttons. Open the door and keep opened: • Start alarm signals or 4 light flashes (depending on arm) INPUT 1 DIGIT.

  • Page 89: Service Mode

    User’s manual Valet mode To temporarily disable the anti-theft and security functions, such as a vehicle service, it is recommended to switch ON service mode. To enable valet mode press and hold 4 seconds button 2 (icon will appear): remote •...

  • Page 90: Remote Engine Start

    3. The automatic temperature start-up function of the engine can be activated regardless of the state of the alarm triggering functions or periodic start-up. * Except StarLine A63 ECO and StarLine A63 models.

  • Page 91: Prepare For Remote Engine Start For Cars With Manual Transmission

    User’s manual Prepear for remote engine start for cars with manual transmission To make remote engine start on cars with manual transmission it is necessarily to perform manual gear reservation. Manual gear reservation is specific sequence of operations by car owner, that garantee, that before remote engine start attempt car will have gear in neutral position.
  • Page 92 StarLine A93, StarLine A63 remote • 1 light flash • LCD shows r99. • If TT is set ON LCD • LED start will show r06. to glow constantly • Engine is running It should be take in account that if brake pedal is depressed, after performing step 1, that would lead to cancel of manual gear reservation.
  • Page 93 User’s manual • in case of turbotimer is set OFF : remote • 1 siren signal; • 1 beep; • 1 light flash; • Indication of • Doors locked; armed mode • Engine shut down engine is ready for remote starts. •...

  • Page 94: Remote Engine Start By Remote Control

    StarLine A93, StarLine A63 When armed mode with the engine running is used vanual gear reservation is also performed. After the engine run time finishes, it can be started by remote control or automatically. Remote engine start by remote control Before remote engine start be sure: •...

  • Page 95: Remote Engine Shut Down

    User’s manual If the engine does not start at the first attempt, then car alarm will take another 3 attempts to start. If after 4 attempts the engine will not start, LCD remote control (provided that it is located in the reception area) will display Remote control will produce 4 beeps informing about the end of engine start procedure.

  • Page 96: Remote Prolongation Of Engine Running Time

    StarLine A93, StarLine A63 Remote prolongation of engine running time When neccessary , you could prolong time of engine running by remote control command: remote • engine running; • LCD indicate remaining time for engine run Press and hold button 1...

  • Page 97: Automatic Engine Start

    User’s manual Auto engine start* To make auto engine start possible: – function 1 table №2 should be programmed to option 2, 3 or 4; – HW circuits should be connected to car alarm (consult installation center). Auto engine start is restricted if: •...
  • Page 98 StarLine A93, StarLine A63 Timer auto engine start In automatic timer start mode, car alarm perform engine start and engine warm according with a specified period of time programmed. Startup period may be set in the range from 2 to 24 hours in increments of 2 hours, and warm-up time is determined by function 2 (see table №2 page 113)
  • Page 99 User’s manual Press button 1 long (untill sound appear) or wait for auto exit (after 4 s.) to memory period of engine start: remote • 2 beeps; • LCD start to show icon , confirming timer engine start mode is active; •...
  • Page 100 StarLine A93, StarLine A63 To activate temperature engine Engine start set cursor on icon and press button 1 short: remote • Melody plays, • During 5s will be indication • 1 light flash of current setting of temperature level. By short press of button 1 set...
  • Page 101 User’s manual Press button 1 long (untill sound appear) or wait for auto exit (after 4 s.) to memory Temperature value for engine start: remote • 2 beeps; • LCD start constantly show icon confirming temperature engine start is active. Auto engine starts disable To switch off alarm clock, timer and temperature starts, set cursor on...
  • Page 102 StarLine A93, StarLine A63 Note: 1) the presence of a remote control in the transceiver range during the auto engine start is not required; 2) actual engine start time may vary with programmed value within 3 minutes; 3) alarm clock engine start is switched on for one start-up cycle.

  • Page 103: Indication Of Engine Running After Engine Started

    User’s manual Indication of engine running after engine started Temperature engine start can be enabled simultaneously with alarm clock or timer periodic engine starts. For ease of determination what mode is really set, after warming time appear index 1-3 corresponding to start mode: •...

  • Page 104: Slave Mode

    - anti-hijack mode. In case of anti-hijacking user should not make any actions. Car alarm will automatically block engine in case tag is not found withing communication range. For StarLine car alarms with installed 2CAN+2LIN, 2CAN or CAN+LIN module.

  • Page 105: Main Terms And Definitions

    The most frequently used method is based on owner ID by tag. For successful user identification tag should be within communication range. If StarLine car alarm will not find host tag it will switch on engine blocking and alarm trigger signals Identification event –...

  • Page 106: Car Alarm Control In Slave Mode

    • Siren and light signals, corresponding to arming procedure will follow;* • Car alarm LED of StarLine car alarm will start to flash In case of trunk, hood,doors are not properly closed or one of the limit switch of door, trunk, hood failed (constantly closed), car alarm will inform by 4 siren signals and 4 light flashes (see.
  • Page 107 • StarLine car alarm will arm and engine will be unblocked • User should pass identification. If StarLine car alarm will produce 3 siren signals and 3 light flashes, that confirms that in armed mode there was alarm trigger.
  • Page 108 StarLine A93, StarLine A63 Version 2: identification by tag After disarming the central unit of StarLine car alarm need to find host tag, which should be within communication range. Search tags occurs only on specific events: disarming — search is started after factory security disarmed;...
  • Page 109 User’s manual Version 3: identification by service button After disarming it is necessary to input PIN-code by valet button (see page 82). Search tags occurs only on specific events: disarming — identification started after factory security disarmed; door open — after car secuirty system disarmed by factory remote control, identification starts after door opened;...
  • Page 110 StarLine A93, StarLine A63 PIN code identification Version 4: (pin-code is input by car factory buttons). This method refers to the authorization when owner input code sequence. The code sequence — is the sequence of pressing buttons of standard car (strictly order).

  • Page 111: Immobilizer With Validator (Pin-Code Identification By Using Car Factory Keys-Buttons)

    User’s manual Immobilizer with validator (PIN-code identification by using car factory keys-buttons) Below is description how to identify your self – inputing code sequence. SLAVE mode is on, function №11 table №1 should be set for option 4 Shutdown and Authorization Algorithm Using a factory key (or by other method) turn factory security sysytem into «disarmed mode»...

  • Page 112: Anti-Hijack Mode

    StarLine A93, StarLine A63 If the car starts moving before entering the pin code or at the time of entry, the engine lock will turn on and alarms will follow. Anti-hijack mode Anti-hijack mode is designed to protect the vehicle from theft in the case of a robbery in disarmed mode.
  • Page 113 User’s manual step 3: engine block • After 120 since door was opened tag search will be stopped doors will be locked, siren signals become constant • Engine will be blocked immidiatelly or after pedal brake pressed (see function 8 table №1). During 45 s engine will be blocked intermittent and then constantly.

  • Page 114: Programming Protection And Service Functions (Table №1)

    The procedure for programming details is described in the installation instructions (could find in can.starline.ru). We do not recommend do it yourself programming. If the need arises, consult expert installers. Change of programming settings or reset to the factory default conditions can cause engine blocking, as well as incorrect operation of car electrical equipment and car alarm itself.
  • Page 115 User’s manual Alarm function RF Variant 1 Variant 2 Variant 3 Variant 4 program table №06 - Siren volume Siren Siren Horn Horn selection №07 – Slave TAG Detection after search to unlock the Detection after disarm Detection after Detection after door during running but without...
  • Page 116 StarLine A93, StarLine A63 Alarm function RF Variant 1 Variant 2 Variant 3 Variant 4 program table Engine run №14 - CH # 2 output 2-step unlock under arm & pulse time Flexy CH HoodLock 0.8 sec Turbo(Follow (yellow-red wire)
  • Page 117 User’s manual Alarm function RF Variant 1 Variant 2 Variant 3 Variant 4 program table Duplication №24 - CH # 7 output Lock Output Flexy CH Pedal Brake of the pulse time (Lock Out) starter №25 - CH # 8 output Duplication pulse time (UnLock UnLock Output...
  • Page 118 StarLine A93, StarLine A63 Programming engine start functions (table №2) Function: Variant 1 Variant 2 Variant 3 Variant 4 Engine Start On Normal car On PTS mode Function with key №1 TT support (on For normal car For normal car...
  • Page 119 User’s manual Function: Variant 1 Variant 2 Variant 3 Variant 4 №8 – Blue wire output ACC (out before Ignition Pedal Brake START select IGN 2 sec) №9 – Cranking time Gray /black wire detect engine 0,8 sec. 1,2 sec. 2,0 sec.
  • Page 120 StarLine A93, StarLine A63 Function: Variant 1 Variant 2 Variant 3 Variant 4 №16 – Choice of ignition START IGN* 2 wire output upon cranking №17 – Disarm with Shutdown Shutdown Shutdown Continue engine status engine engine engine №18 – The duration of...

  • Page 121: Remote Controls Battery Exchange

    User’s manual Remote controls battery exchange In remote controls are used different batteries: - in the LCD remote control – 1 battery «AAA» 1.5 V - in remote control without display – 1 battery «CR2450» 3.0 V Because of the remote controls are always in the standby mode of the radio signals from the central unit, the energy consumption of the battery happens all the time.
  • Page 122 StarLine A93, StarLine A63...
  • Page 123 User’s manual The manufacturer reserves the right to make changes in design and items without prior notice. Manufacturer: Limited Liability Company «Scientific-Production Association «StarLine» (LLC «SPA “StarLine») 194044, Russia, Saint–Petersburg, 9 Comissara Smirnova St.
  • Page 124 StarLine A93, StarLine A63...

This manual is also suitable for:

A63A93 2can+2linA93 ecoA93A93 gsm

Table of Contents