Related Manuals for Bonex ECOS
Summary of Contents for Bonex ECOS
- Page 1 BONEX-SCOOTER Instruction for use INSTRUCTION FOR USE BONEX-SCOOTER ECOS REFERENCE DISCOVERY REFERENCE RS DISCOVERY RS Version: 2016_08...
-
Page 2: Table Of Contents
Illustration 7b (Scooter top side) ............10 Illustration 7c (Scooter bottom side) ............11 8. Starting up....................13 8.1 Proper opening / closing procedure of Bonex-Scooters ....14 8.2 Scoter Trim ..................17 8.3 Controls to perform before starting up ..........17 9. -
Page 3: Safety Instructions
BONEX-SCOOTER Instruction for use 1. Safety Instructions The Bonex-Scooter is a top quality product made in Germany. However, the product is only as good as can be guaranteed with proper, careful handling and care of all parts. We therefore ask you to read the following instructions for use and care of the scooter carefully. - Page 4 BONEX-SCOOTER Instruction for use The scooter has double seals on all shaft openings and housing seals. To ensure that the seals seal perfectly, the seals must be cleaned and greased regularly! The scooter is supplied with a control voltage after switching on the main switch.
-
Page 5: Warning Instructions
BONEX-SCOOTER Instruction for use 1.3 Warning Instructions In case any flooding, stop immediately the driving and use. In case of a flooded battery, the battery and the scooter burn explode. This is extremely dangerous. The extinguishing can only be done with the fire extinguishing device for lithium batteries. -
Page 6: Brief Instructions For Bonex-Scooter
BONEX-SCOOTER Instruction for use 2. Brief instructions for Bonex-Scooter 1. Read the manual carefully before operating the device! 2. Storage: Main switch „OFF“ (otherwise total damage of battery is possible!) Place scooter with “Shroud“ down on flat ground or store it in the transport box with the label “TOP”... - Page 7 Occasionally check or exchange the zinc anode. Please heed the advice for a smooth run of the scooter and a long joy over your Bonex-Scooter! This is just a quick check. This does not show the complete maintenance. If desired, Bonex will do the service for you.
-
Page 8: Purpose
Operation in other media can lead to malfunctions or overheating of the motor and to damage or even destruction of the Bonex-Scooter. The Bonex-Scooter is designed to pull a diver and his personal and auxiliary equipment. The maximum performance values depend on the weight and the streamlined arrangement of the equipment in the water. -
Page 9: Guarantee
Defective sealing elements must be replaced immediately. Bonex will accept no liability for penetration by water (especially salt water) which is due to defective elements and poor maintenance. The replacement or exchange of single parts (i.e. battery) does not extend the guarantee. -
Page 10: Disclaimer
The owner is solely responsible for the trouble-free, proper and orderly operation of the Bonex-Scooter! Bonex will accept no liability for damage due to improper use of the scooter. This includes damage to natural banks, jetties and harbours and diving in private, protected and security areas. -
Page 11: Technical Data
BONEX-SCOOTER Instruction for use 6. Technical Data ECOS ECOS Plus ECOS S REFERENCE DISCOVERY Model Ø 223/300 Ø 223/300 Ø 223/300 Ø 218/300 Ø 218/300 Dimensions: L 600 mm L 600 mm L 600 mm L 690 mm L 850 mm... -
Page 12: Technical Description
Battery (2X at DISCOVERY series!) Stop ring (Battery fixation) Connecting rod Tube Motor Main switch (ECOS with 5 speed steps) Zinc anode Cross member Tow cord fixation point Emergency drive-switch (NOT at ECOS) Round handle Drive switch (Trigger) Main switch... -
Page 13: Illustration 7C (Scooter Bottom Side)
BONEX-SCOOTER Instruction for use Version: 2016_08 Page 11... - Page 14 BONEX-SCOOTER Instruction for use Version: 2016_08 Page 12...
-
Page 15: Starting Up
BONEX-SCOOTER Instruction for use 8. Starting up The Bonex-Scooter is prepared for starting already prior to delivery. The battery is charged and the scooter is parameterized with the latest software. On manufacture, the scooter is subjected to a function and pressure test. -
Page 16: Proper Opening / Closing Procedure Of Bonex-Scooters
BONEX-SCOOTER Instruction for use 8.1 Proper opening / closing procedure of Bonex-Scooters Closed state of scooter in „Nose view” Lift the silver eccentric lever up to complete vertical position. Now two red dots arranged in alignment are visible. Turn the silver eccentric lever to left or right side for 90°. - Page 17 BONEX-SCOOTER Instruction for use View of scooter with nose removed. If Tube has not been removed for a longer time it is possible that the two O-ring, displace the smear layer and you need an intensified force to remove the Tube.
- Page 18 BONEX-SCOOTER Instruction for use When refitting the Tube pay attention to the correct position of the “Logo-Signs”. Push the nose with slight force downwards to refit it to the scooter. To do this way, the system handle must be aligned to the drive switch (trigger).
-
Page 19: Scoter Trim
BONEX-SCOOTER Instruction for use 8.2 Scooter Trim: For using our scooters in saltwater, please use the additional lead balance weights as follows: For determination of the needed quantity of lead, please put your scooter into saltwater and put some of the big lead (thin and/or thick) on the front of the tube. -
Page 20: Controls To Perform Before Starting Up
BONEX-SCOOTER Instruction for use 8.3 Controls to perform before starting up Ensure that the power pack is sitting tight and connect the battery plug. The battery plug only fits in one position so that the union nut also engages. Screw the union nut of the battery plug to the end of its thread so that the plug is also tight. - Page 21 When the mark on the governor switch is at 12 a clock you reach a pull speed of approx. 60%. The main switch of the ECOS model also functions as a five speed step switch. After releasing the drive switch press the emergency drive switch by pushing the round piece to its outer rest position.
-
Page 22: Use
BONEX-SCOOTER Instruction for use 9. Use You should use a backplate with harness and crotch belt for riding the scooter. When using an ADV or stabilizing jacket you can attach a crotch strap additionally to your lead belt, or use a separate waist belt with crotch strap while using a lead-integrated jacket. -
Page 23: Most Important Points To Be Mentioned
BONEX-SCOOTER Instruction for use 9.1 Most important points to be mentioned Increase your speed gradually. Make sure that the use of electric powered scooters is not prohibited in the waters you are using. Look out for other divers or swimmers. When using the scooter near to marine and wildlife sanctuaries, be careful to keep a good distance to avoid entering these areas under water. -
Page 24: Average Performance And Range
BONEX-SCOOTER Instruction for use 9.2 Average performance and range 9.2a UNIVERSAL-Model „ECOS“ ECOS Slow Medium Fast Little equipment Speed: 45 m / min 53 m / min 60 m / min Run time: 200 min 150 min 110 min Range:... -
Page 25: B „Explorer" Models
BONEX-SCOOTER Instruction for use ECOS S Slow Medium Fast Little equipment Speed: 45 m / min 53 m / min 60 m / min Run time: 200 min 150 min 90min Range: 8-9 km 8 km 5,4 km Double unit with 1-2 stages... -
Page 26: C „Performance" Models (Rs)
BONEX-SCOOTER Instruction for use 9.2c „PERFORMANCE“ Models (RS) REFERENCE RS Langsam Mittel Schnell Little equipment Speed: 45 m / min 60 m / min 85 m / min Run time: 210 min 150 min 105 min Range: 9,4 km 9,0 km... -
Page 27: Transport And Storage
BONEX-SCOOTER Instruction for use 10. Transport and storage The battery should be disconnected from the scooter at the plug for storage and transport. This also prevents the scooter from being accidentally switched on. This is absolutely essential for transport by courier or parcel service. -
Page 28: Charging The Battery
The connection can be operated in Europe on the 230V DC mains or in other countries with 110V. The charging time may increase under such conditions. Standard-Charger for ECOS models – 110 / 230V charger switches automatically The charger has 1 diode (red / green). -
Page 29: Maintenance And Care
After longer use, the spring of the sliding ring seal should be removed and its O-rings greased. 12.1 Maintenance intervals of Bonex-Scooter To be Maintenance point Interval... -
Page 30: Table Of Performed Maintenance
BONEX-SCOOTER Instruction for use 12.2 Table of performed maintenance Wartung Date Date Date Date Oil housing with silicone Check battery and cable Oil rotary switch Change housing O-rings Change scooter nose O-rings Change O-rings axles / shaft Change sliding ring seal... -
Page 31: Accessories And Spare Parts
BONEX-SCOOTER Instruction for use 13. Accessories and spare parts 13.1a Accessories Article Article-No. Spare battery ECOS LiMn SC-710 Spare battery REFERENCE, DISCOVERY (RS) LiMn SC-705-2 System handle SC-501 Round handle extension “Left-Side” SC-514 Standard-Charger ECOS SC-504 QCS-Charger REFERENCE, DISCOVERY (RS) -
Page 32: Accessories
Propeller 3 Blades (SPEED) SC-707 Upgrade set REFERENCE (RS) > DISCOVERY (RS) SC-205 Upgrade set DISCOVERY (RS) > REFERENCE (RS) SC-207 Bonex ECOS Scooter - Set SC-007 Bonex REFERENCE Scooter - Set SC-002 Bonex REFERENCE RS Scooter - Set SC-003... -
Page 33: Spare Parts
BONEX-SCOOTER Instruction for use 13.2 Spare parts Pos. Count Name Order number Zinc anode 11-11009 Locking screw 11-11007 Propeller 11-13003 / -13007 Pressure disc 19-41006 Synchronous motor; 48V Sliding ring seal; D=12mm Grooved ball bearing; D=15mm Reed sensor; D=6mm Magnet; D=6mm;... -
Page 34: Blow-Up Drawing Scooter
BONEX-SCOOTER Instruction for use 13.3 Blow-up drawing Scooter Version: 2016_08 Page 32... - Page 35 BONEX-SCOOTER Instruction for use Version: 2016_08 Page 33...
- Page 36 BONEX-SCOOTER Instruction for use Version: 2016_08 Page 34...
-
Page 37: Troubleshooting
BONEX-SCOOTER Instruction for use 14. Troubleshooting In case of malfunctions or failure, the table below presents a list of the most typical problems. Fault Cause of failure Remedy >Battery plug not connected >Connect >Battery empty >Recharge battery >Main switch „OFF”... - Page 38 BONEX-SCOOTER Instruction for use Fault Cause of failure Remedy >Rinse with water and Switches sluggish >Dirt / sand on axle >oil axle afterwards >Clean grooves Housing, tube >O-rings soiled >Clean / change O-rings sluggish >Grease housing with silicone >Axle dry >Achse mit Silikon fetten...
- Page 39 BONEX-SCOOTER Instruction for use Version: 2016_08 Page 37...