Protekt P-90 Instruction Manual

· a full body harness (conforming to EN 361) is the only acceptable body holding device that can be used, in a fall arrest system.
· in full body harness use only attaching points marked with big letter "A" to attach a fall arrest system.
· the anchor device or anchor point for the fall arrest system should always be positioned, and the work carried out in such a way, as
to minimise both the potential for falls and potential fall distance. The anchor device/point should be placed above the position of the
user . The shape and construction of the anchor device/point shall not allowed to self-acting disconnection of the equipment.
Minimal static strength of the anchor device/point is 12 kN. It is recommended to use certified and marked structural anchor point
complied with EN795
· it is obligatory to verify the free space required beneath the user at the workplace before each occasion of use the fall arrest system,
so that, in the case of a fall, there will be no collision with the ground or other obstacle in the fall path. The required value of the free
space should be taken from instruction manual of used equipment.
· there are many hazards that may affect the performance of the equipment and corresponding safety precautions that have to be
observed during equipment utilization, especially: - trailing or looping of lanyards or lifelines over sharp edges, - any defects like
cutting, abrasion, corrosion, - climatic exposure, - pendulum falls, - extremes of temperature, - chemical reagents, - electrical
conductivity.
· personal protective equipment must be transported in the package (e.g.: bag made of moisture-proof textile or foil bag or cases
made of steel or plastic) to protect it against damage or moisture.
· the equipment can be cleaned without causing adverse effect on the materials in the manufacture of the equipment. For textile
products use mild detergents for delicate fabrics, wash by hand or in a machine and rinse in water. Plastic parts can be cleaned only
with water. When the equipment becomes wet, either from being in use or when due cleaning, it shall be allowed to dry naturally,
and shall be kept away from direct heat. In metallic products some mechanic parts (spring, pin, hinge, etc.) can be regularly slightly
lubricated to ensure better operation. Other maintenance and cleaning procedures should be adhered to detailed instructions
stated in the manual of the equipment.
· personal protective equipment should be stored loosely packed, in a well-ventilated place, protected from direct light, ultraviolet
degradation, damp environment, sharp edges, extreme temperatures and corrosive or aggressive substances.
IT IS THE RESPONSIBILITY OF THE USER ORGANISATION TO PROVIDE THE IDENTITY CARD AND TO FILL IN THE DETAILS
REQUIRED. THE IDENTITY CARD SHOULD BE FILLED IN BEFORE THE FIRST USE BY A COMPETENT PERSON,
RESPONSIBLE INTHE USER ORGANIZATION FOR PROTECTIVE EQUIPMENT. ANY INFORMATION ABOUT THE EQUIPMENT
LIKE PERIODIC INSPECTIONS, REPAIRS, REASONS OF EQUIPMENT'S WITHDRAWN FROM USE SHALL BE NOTED INTO THE
IDENTITY CARD BY A COMPETENT PERSON. THE IDENTITY CARD SHOULD BE STORAGED DURING A WHOLE PERIOD OF
EQUIPMENT UTILIZATION. DO NOT USE THE EQUIPMENT WITHOUT THE IDENTITY CARD. ALL RECORDS IN THE IDENTITY
CARD CAN BE FILLED IN ONLY BY A COMPETENT PERSON.
IDENTITY CARD
MODEL AND TYPE OF EQUIPMENT
SERIAL NUMBER
USER NAME
DATE OF PURCHASE
PERIODIC EXAMINATION AND REPAIR HISTORY
REASON FOR
DATE
ENTRY PERIODIC EXAMINATION
OR REPAIR AND OTHER REVELANT INFORMATIONS
1
2
3
4
PROTEKT, 93-403 LODZ,
ul. Starorudzka 9, POLAND,
TEL: (48 42) 680 20 83, FAX: (48 42) 680 20 93
www.protekt.com.pl
REF. NUMBER
DATE OF MANUF.
DATE OF PUTTING
INTO OPERATION
DEFECTS NOTED, NAME AND SIGNATURE
REPAIRS CARRIED OUT OF COMPETENT PERSON
Notified body, at which the European certification
was performed and which supervises
the production of the equipment:
APAVE SUDEUROPE SAS - BP 193 - 13322 MARSEILLE CEDEX 16 - FRANCE
Instruction Manual
READ CAREFULLY BEFORE USE THE EQUIPMENT
Safety harness is the basic
element of fall arrest
equipment.
The harness P-90 complies
with EN 361 (as a full body
harness), EN 358 (as a
work positioning belt) and
EN 813 (as a sit harness) -
the maximum load of the sit
harness is 140 kg.
The harness is made of
polyester webbings.
1. Shoulder strap.
2. Shoulder strap adjusting buckle.
3. Frontal attachment D-ring - for attaching fall arrest
system.
4. Connecting snap hook.
5. Frontal waist attachment buckle - can be utilized as a sit
harness according EN 813 (it's not allowed to use this
buckle to attach fall arrest system).
6. Lateral belt attachment D-rings. Can be utilized only to
attach work positioning systems according EN 358.
7. Work positioning belt strap.
8. Work positioning belt strap adjusting buckles.
9. Thigh straps.
10. Thigh straps connecting/adjusting buckles.
10. Thigh straps connecting/adjusting buckles.
PERIODIC
EXAMINATION
NEXT DUE DATE
HARNESS MARKING
a-Device type, b-Model symbol, c-Reference
number, d-number/year European standards
e-CE mark and number of the notified body
controlling manufacturing of the equipment,
f- Month and year of manufacture, g-Serial number of
the harness, h-Harness size,
i-Caution: read the manual, j- identification of the
harness manufacturer or distributor.
k - max. weight for the sit harness use.
SAFETY HARNESS P-90
EN 361:2002
EN 358:1999
Ref. AB 190 01
EN 813:2008
1
2
3
A
4
5
6
7
9
10
11. Dorsal attachment D-ring - for attaching fall arrest
system.
12. Rear waist attachment D-ring - for attaching
restraint and work positioning systems.
13. Dorsal strap adjusting buckle.
14. Belt pad.
15. Rear leg straps adjusting buckle.
16. Tool Loops.
17. Identity label
SIZES
The harness is manufactured in two sizes:
- medium and extra large size - M-XL
- extra large -XXL
e a c
b
P-90
SAFETY HARNESS
Ref. AB 190 01
EN 361:2002
EN 358:1999
EN 813:2008
max. load 140 kg
k
A
11
13
12
14
16
15
8
g j
d f i h
M-XL
Date of manufacture: Size:
12.2011
XXL
Serial number:
0000001