Hubbell Dual Lite EV Series Installation, Operation And Service Instructions

Installing the Unit: Final Assembly
Installing the Unit: Final Assembly
1. Align housing slots over tabs on backplate.
1. Align housing slots over tabs on backplate.
2. Pivot housing and snap closed.
2. Pivot housing and snap closed.
3. Aim the lamps. Do not press on the lenses.
3. Aim the lamps. Do not press on the lenses.
SERVICE/MAINTENANCE
SERVICE/MAINTENANCE
Service / Maintenance
Maintenance
Maintenance
This emergency lighting unit should be tested and maintained in accordance with National Electrical Code and NFPA 101 Life Safety
This emergency lighting unit should be tested and maintained in accordance with National Electrical Code and NFPA 101 Life Safety
Code requirements. It is recommended that emergency light fixtures be tested for 30 seconds once a month and for 90 minutes once a
Code requirements. It is recommended that emergency light fixtures be tested for 30 seconds once a month and for 90 minutes once a
year.
year.
Taking A Unit Out Of Service
Taking A Unit Out Of Service
If a unit is to be deliberately taken out of service for an extended period, the battery lead connector should be disconnected from the
If a unit is to be deliberately taken out of service for an extended period, the battery lead connector should be disconnected from the
charger circuit board and insulated so that the battery will go into storage in a fully charged condition.
charger circuit board and insulated so that the battery will go into storage in a fully charged condition.
Replacing The Battery
Replacing The Battery
1. De-energize the AC power.
1. De-energize the AC power.
2. Disengage the housing cover from the backplate.
2. Disengage the housing cover from the backplate.
3. Disconnect the battery leads from the charger circuit board.
3. Disconnect the battery leads from the charger circuit board.
4. Remove the battery from the clips inside the cover.
4. Remove the battery from the clips inside the cover.
5. Replace with a new battery (see unit model label for correct part number) and reconnect leads.
5. Replace with a new battery (see unit model label for correct part number) and reconnect leads.
6. Reassemble cover to backplate.
6. Reassemble cover to backplate.
Replacing LED Lamps
Replacing LED Lamps
The LED lamps inside the unit are not replaceable or field serviceable. Please see dual-lite.com for further assistance.
The LED lamps inside the unit are not replaceable or field serviceable. Please see dual-lite.com for further assistance.
Troubleshooting
Troubleshooting
Emergency circuit does not work
Emergency circuit does not work
• Batteries are shipped uncharged and disconnected. Connect battery leads and charge 24 hours before testing.
• Batteries are shipped uncharged and disconnected. Connect battery leads and charge 24 hours before testing.
• Make sure the charger board and test button/light pipe are properly seated and aligned.
• Make sure the charger board and test button/light pipe are properly seated and aligned.
• Check wiring connections.
• Check wiring connections.
RECYCLING INFORMATION
RECYCLING INFORMATION
All steel, aluminum, and thermoplastic parts are recyclable.
All steel, aluminum, and thermoplastic parts are recyclable.
NOTICE: Emergency units contain rechargeable batteries which
NOTICE: Emergency units contain rechargeable batteries which
must be recycled or disposed of properly.
must be recycled or disposed of properly.
RECYCLING INFORMATION
Hubbell Lighting, Inc. Life safety Products • www.dual-lite.com
Hubbell Lighting, Inc. Life safety Products • www.dual-lite.com
All steel, aluminum and thermoplastic parts are recyclable.
NOTICE: Emergency units contain rechargeable batteries which
Copyright© Hubbell Lighting, Inc., All rights reserved • Specifications subject to change without notice.
Copyright© Hubbell Lighting, Inc., All rights reserved • Specifications subject to change without notice.
must be recycled or disposed of properly.
Hubbell Lighting, Inc. Life Safety Products • www.dual-lite.com
Copyright Hubbell Lighting, Inc., All Rights Reserved • Specifications subject to change without notice. • Printed in U.S.A.
©
93033106_B 10/14
INSTALLATION
Printed in U.S.A.
Printed in U.S.A.
93033106_A 2/11
93033106_A 2/11
IMPORTANT SAFEGUARDS
IMPORTANT SAFEGUARDS
93034799
When using electrical equipment, basic safety precautions
When using electrical equipment, basic safety precautions
IMPORTANT SAFEGUARDS
should always be followed, including the following:
should always be followed, including the following:
READ AND FOLLOW ALL SAFETY
READ AND FOLLOW ALL SAFETY
When using electrical equipment, basic safety precautions should
READ AND FOLLOW ALL SAFETY
1. Do not use outdoors.
1. Do not use outdoors.
2. Do not let power supply cord touch conductive surfaces.
2. Do not let power supply cord touch conductive surfaces.
3. Do not mount equipment near gas or electric heaters.
3. Do not mount equipment near gas or electric heaters.
4. Equipment should be mounted in locations and at heights where it will not readily be subject
4. Equipment should be mounted in locations and at heights where it will not readily be subject
to tampering by unauthorized personnel.
to tampering by unauthorized personnel.
1. Do not use outdoors.
5. The use of accessory equipment not authorized by the manufacturer may cause an unsafe
5. The use of accessory equipment not authorized by the manufacturer may cause an unsafe
2. Do not let power supply cords touch hot surfaces.
condition.
condition.
3. Do not mount near gas or electric heaters.
6. Do not use this equipment for other than its intended purpose.
6. Do not use this equipment for other than its intended purpose.
4. Equipment should be mounted in locations and at heights where it will not readily be subject
7. Servicing of this equipment should be performed by qualified service personnel.
7. Servicing of this equipment should be performed by qualified service personnel.
to tampering by unauthorized personnel.
8. Test cycling: the Life Safety Code (NFPA 101) requires testing of emergency lighting units
8. Test cycling: the Life Safety Code (NFPA 101) requires testing of emergency lighting units
5. The use of accessory equipment not authorized by the manufacturer may cause an
once a month for a minimum of 30 seconds, and once a year for a minimum of 90 minutes.
once a month for a minimum of 30 seconds, and once a year for a minimum of 90 minutes.
unsafe condition.
6. Do not use this equipment for other than its intended purpose.
7. Servicing of this equipment should be performed by qualified service personnel.
SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS
SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS
8. Test cycling: the Life Safety Code (NFPA 101) requires testing of emergency lighting units once a month for a
SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT
SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT
minimum of 30 seconds, and once a year for a minimum of 90 minutes.
WARNING – This product contains chemicals known to the state of California to cause cancer, birth
WARNING – This product contains chemicals known to the state of California to cause cancer, birth
•SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS
defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or
defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or
•SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT
otherwise touching this product.
otherwise touching this product.
WARNING – This product contains chemicals known to the State of California to cause cancer, birth
Emergency Lighting Equipment For Use In Damp Locations
Emergency Lighting Equipment For Use In Damp Locations
defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning,
Damp location listed units are suitable for installation in:
Damp location listed units are suitable for installation in:
or otherwise touching this product.
1. Interior locations subject to moderate degrees of moisture, such as some basements, some barns,
1. Interior locations subject to moderate degrees of moisture, such as some basements, some barns,
some cold storage warehouses, and the like.
some cold storage warehouses, and the like.
Emergency Lighting Equipment For Use in Damp Locations
2. Partially protected locations under canopies, marquees, roofed open porches and the like.
2. Partially protected locations under canopies, marquees, roofed open porches and the like.
93034795 Damp location listed units are suitable for installation in:
93034797
1. Interior locations subject to modreate degrees of moisture, such as some basements, some barns, some cold storage
93034799
warehouses, and the like.
93034800
93035762
2. Partially protected locations under canopies, marquees, roofed open porches and the like.
Twin-Head LED Emergency Lighting Unit
Twin-Head LED Emergency Lighting Unit
Twin-Head LED Emergency Lighting Unit
Standard, Remote, and Spectron® Equipped Models
Standard, Remote, and Spectron® Equipped Models
Standard, Remote, and Spectron
Installation, Operation, and Service Instructions
Installation, Operation, and Service Instructions
Installation, Opperation, and Service Instructions
always be followed including the following.
INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
INSTALLER:
INSTALLER:
INSTALLER:
EV Series
Equipped Models
®
93034800