Enrolling Wireless Buttons; Enrolling Sirens; Enrolling Ja-80L; Enrolling Ja-80A - JabloCom EYE-02 Application Note

9.4

Enrolling wireless buttons

Switch the camera into Enroll mode. Go to JabloTool via internet, tab Peripherals and click on Add new device. Other
•
possibilities of switching camera to Enroll mode are described in chapter 9.1.
Press (any) button on wireless button: RC-80, RC-85, RC-87, RC-88, RC-89
•
9.5

Enrolling sirens

Siren should be at least 2 meters away from the camera during enrolment.
9.5.1

Enrolling JA-80L

1. Reset the siren if it has been previously enrolled in another device
Unplug the siren from the mains socket.
•
Press and hold the siren button and plug the siren in the mains socket.
•
Keep the button pressed until two beeps are heard which confirms a reset.
•
2. The indicator keeps flashing after reset (device is in enrolment mode).
3. Send the enrolment signal from the camera
Go to JabloTool via internet, tab Peripherals and click on Add new device. Other options are described in the chapter
9.3.1, step 4.
9.5.2

Enrolling JA-80A

1. If another device has been previously enrolled in the siren reset the siren by unplugging its battery.
2. Switch the camera into enroll mode. The options are described in the chapter 9.1.
3. Insert battery into the siren.
The siren stops flashing after it is enrolled.
9.6

Enrolling thermostats and camera into wireless switches

If you want to use wireless switch with
you can enroll the camera. Follow these steps.
1. Enroll the thermostat into the controlling wireless switch
Reset the
wireless switch
•
the chapter
9.3.3, step 1
Switch the
wireless switch
•
AC-82 or UC-82: Repeatedly press the relevant X or Y button of the wireless switch until all 4 LED lights flash
•
AC-83: press the button X or Y, enroll mode is indicated by red LED number 2 or 4 flashing.
•
Insert battery into
•
2. Enroll the camera into the controlled wireless switch (it is described in the chapter 9.3.2/9.3.3, steps 2 and 3).
9.6.1
Enrolling
thermostats into EYE-02 camera
1. Switch the camera into Enroll mode (it is described in chapter 9.1)
2. Insert battery into the thermostat TP-82 or TP-83
9.6.2

Enrolling thermostats and camera into wireless socket AC-88

1. First reset the socket.
You can skip step 1 if no other device is enrolled in the socket. Its reset is described in the chapter 9.3.1, step 1.
2. Plug the socket into the mains. LED indicator flashes once.
3. Right afterwards, press and hold the button on the socket until the LED indicator flashes once in intervals.
4. Insert battery into the thermostat TP-82 or TP-83
5. Press the socket button to finish the enrollment mode.
6. Unplug the socket from the mains
7. Plug the socket into the mains. LED indicator flashes once.
8. Right afterwards, press and hold the button on the socket until the LED indicator flashes once in intervals.
9. Send enrollment signal from the camera.
Go to JabloTool via internet, tab Peripherals, press Add new device. Other options are described in the chapter
9.3.1, step 3.
The wireless socket will now connect contact if thermostat gives command to increase the temperature.
EYE-02.ENG.MAN.APN.Wireless_peripherals.01.docx
both
thermostat and the camera you need to enroll thermostat into the switch first then
AC-82, UC-82
(it is described in chapter 9.3.2, step 1)
)
into mode
enroll
TP-82 or TP-83.
the thermostat
- 13 -
or AC-83 (it is described in