Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Relay PadPuls M1
Summary of Contents for Relay PadPuls M1
- Page 1 PadPuls M1 1-channel M-Bus pulse converter for reed signals User Manual...
-
Page 2: Table Of Contents
5.4 Reed-Input ........................16 5.5 Requirements to contacts of pulse generators .............. 16 5.6 Ordering information ...................... 16 This documentation is valid from M-Bus generation: $09 © Relay GmbH 2018 www.relay.de User Manual PadPuls PadPuls M1 · 10/2018 · VERSION 1.4... -
Page 3: Functional Description
MBCONF is very easy. When connected to the M-Bus the PadPuls M1 is powered by the bus. A built-in battery ensures that metering continues even if the M-Bus fails for longer than the normal calibration time of the water meter or heat counter. -
Page 4: Installation And Startup
Use a suitable adhesive seal to prevent unnoticed opening of the housing. 2.3 Connecting The following drawing shows a typical application of the PadPuls M1: M-Bus Master PadPuls M1 pulse generator (blue) User Manual PadPuls PadPuls M1 ·... - Page 5 Attention: The battery jumper is plugged in at the factory and should not be removed as the PadPuls M1 will otherwise lose configuration. In this case, a new configuration including programming of the ID is necessary. User Manual PadPuls PadPuls M1 · 10/2018 · VERSION 1.4...
-
Page 6: Parameterization Using Mbconf
We recommend our service tool Micro-Master USB (art.no. MR003USB). The PadPuls M1 to be parameterized must be connected directly (i.e. as only M-Bus device) to the M-Bus output of the level converter. -
Page 7: Sheet Info
PadPuls M1 3.3 Sheet Info This sheet shows some photos of supported M-Bus devices from the product range of the Relay GmbH, the PadMess GmbH and further manufacturers. Here are also links to our Internet page, from which the current version of the program can be downloaded, and to the email address for criticism and suggestions to the program. - Page 8 Generation shows the revision connected M-Bus device. This item is read only. Type shows the type (here: PadPuls M1) of the connected device. This item is read only. M-Bus State shows the M-Bus state of the connected device. This item is read only.
- Page 9 The following buttons are also always visible: Erase log clears all outputs inside the log window. Exit terminates the program and stores the current setting of serial port (port no.) into the INI file User Manual PadPuls PadPuls M1 · 10/2018 · VERSION 1.4...
-
Page 10: Sheet M1
PadPuls M1 3.4 Sheet M1 This sheet shows the current settings and values of the PadPuls M1. The following input boxes and buttons are used to change the parameters of the pulse adapter: Prim. address is the primary M-Bus address of the selected device. Values between 1 and 250 can be entered in this field for new assignment of the address. - Page 11 “Unprotect” pushbutton. Permanent Error is not used for the PadPuls M1. Write protect transmits a command to the PadPuls M1 to activate write protection. The PadPuls then allows no further configuration. It is protected against unnoticed manipulation.
- Page 12 Choice: Unit = 1kWh, Multiplicator = 1 / 64, Counter = 78346 ( x 1kWh) • Electricity meter with counter = 112,345 kWh and 1000 pulses / kWh: Choice: Unit = 1Wh, Multiplicator = 1 / 1, Counter = 1123454 ( x 0,001Wh) User Manual PadPuls PadPuls M1 · 10/2018 · VERSION 1.4...
-
Page 13: Bus Telegrams
• Count: Meter reading (most-significant byte = Count6 always zero) • Numerator / Denominator: Impulse value (increment in multiples of the VIF per impulse): Numerator • VIF 1 Pulse = Denominator User Manual PadPuls PadPuls M1 · 10/2018 · VERSION 1.4... - Page 14 4) Telegram to Set the Write Protection Byte Name Start Length Length Start Spez. Protect Stop Inhalt The write protection can only be reset by pressing the pushbutton on the circuit board. See chapter 2.3. User Manual PadPuls PadPuls M1 · 10/2018 · VERSION 1.4...
-
Page 15: Technical Data
Typical 6A (contact open), plus 4A for closed contact Battery lifetime At 25°C: min. 9 years (contacts open, max. 50 Mio. pulses per year.) At 60°C: min. 7 years (contacts open, max. 50 Mio. pulses per year.) User Manual PadPuls PadPuls M1 · 10/2018 · VERSION 1.4... -
Page 16: Reed-Input
<= 12,5 Hz at pulse length = pause length (each 40 ms) 5.6 Ordering information Artikelnummer Beschreibung IM001G PadPuls M1, 1-channel M-Bus pulse converter, wall mounting IM001 PadPuls M1, 1-channel M-Bus pulse converter, only board without housing User Manual PadPuls PadPuls M1 · 10/2018 · VERSION 1.4...