Related Manuals for Relay AnDi1
Summary of Contents for Relay AnDi1
- Page 1 A/D Converter for M-Bus AnDi1, AnDi2, AnDi3, AnDi4 With 1,2,3 or 4 input channels User Manual...
-
Page 2: Table Of Contents
3.3 Sheets AnDi4 Port1..4 ....................11 4 M-Bus Telegrams ........................14 5 Technical Data ........................17 6 CE Declaration ........................18 (Valid from M-Bus generation: $31) © Relay GmbH 2017 www.relay.de User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3... -
Page 3: Functional Description
The AnDi 1 to 4 don´t differ in the front cover, but the devices are marked with an additional label on the housing showing the article no. The terminals of the unavailable inputs are also not present. User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3... -
Page 4: Installation And Startup
In normal operation this LED is on during measuring after a read from M-Bus. 2.2.2 M-Bus The M-Bus is linked polarity independent to the terminals labelled with “M-Bus”. User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3... - Page 5 In p u t fo r c u r r e n t m e a s u r e m e n t G r o u n d p o te n tia l User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3...
-
Page 6: Opening The Case
The screwdriver is placed, as in the drawing, into the small opening at the cover side. After moving of the screwdriver in the displayed direction the cover can be taken off. Picture 6: Opening the case User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3... -
Page 7: Parameterization Using Mbconf
After a successful connection with the M-Bus device, further manufacturer information is shown in the sheet “Info” and additional device- specific sheets are displayed. User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3... -
Page 8: Sheet Info
AnDi1/2/3/4 3.3 Sheet Info This sheet shows some photos of supported M-Bus devices from the product range of the Relay GmbH, the PadMess GmbH and further manufacturer. Here are also links to the Internet page, from which the current version of the program can be downloaded, and to the email address for criticism and suggestions to the program. - Page 9 (e.g. PadPuls M4 / M4L). The software always reads the data after writing, if this option is Autom. Readout activated (useful for checking the correct programming). User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3...
- Page 10 Erase log terminates the program and stores the current setting of serial port Exit (port no.) into the INI file. User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3...
-
Page 11: Sheets Andi4 Port1
8 digit M-Bus ID (identification no.), which is also used for secondary addressing of this port. describes the measured medium of the connected meter. Medium Examples: Oil, Water, Heat, Electricity User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3... - Page 12 Value at 20mA/10V is the upper limit of the measuring range at 20mA or 10V. Transmits a command to the AnDi4 to activate write protect. The Write protect AnDi4 then allows no further configuration. It is protected against unnoticed manipulation. User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3...
- Page 13 The examples demonstrate that the selection of the unit has a direct influence to the resolution of the measurement. The optimal settings for these examples are the suggestions marked with “a)”. User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3...
-
Page 14: Bus Telegrams
(upper limit) Anw.: is only used by AnDi4 for addressing with primary address 254 for selection of one channel: (00: Port1, 01: Port2, 02: Port3, 03: Port4). checksum User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3... - Page 15 Bit7-4: Information about the available modules in AnDi4 Bit3: protection bit (1: protected) Bit2-1: no. of selected channel (0: Port1 ... 3: Port4) Bit0: operating mode (1: current, 2: voltage) User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3...
- Page 16 Start Prot. Stop Value (hex): Protection telegramm Selecting the channel for use with address 254 Position Name Start Length Length Start Anw. Stop Value (hex): Selection telegramm User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3...
-
Page 17: Technical Data
EN1434-3 Transmission speed 300 or 2400 Baud Addressing Primary and secondary addressing with wildcards, each channel : 1 primary and secondary address Supported functions SND_NKE, REQ_UD2, SND_UD User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3... -
Page 18: Ce Declaration
AnDi1/2/3/4 6 CE Declaration User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3... - Page 19 AnDi1/2/3/4 Notes: User Manual AnDi1 / AnDi2 / AnDi3 / AnDi4 ·10/2017 · VERSION 1.3...