Table of Contents
Advertisement
Reservedele / Spare Parts / Ersatzteile / Piéces détachées
Betegnelse
Pos. no.
Designation
Kondensator
43
Capacitor
Ventilator
1
Fan
Motor m. skråskive, (230V,50Hz)
3
Motor w. wobble disc
Motor m. skråskive, (240V,50Hz)
3
Motor w. wobble disc
Rep. sæt skråskive
4
Rep. kit wobble disc 140 bar
Rep. sæt leje
5
Rep. kit bearing
Rep. sæt stempel
11
Rep. kit piston
Rep. sæt automatisk s/s ventil
20
Rep. kit automatic s/s valve
Box m. kontakt & kabel
24
Box w. switch & cable
Rep. sæt tætningssystem
25
Rep. kit sealing system
Rep. sæt ventilsystem
26
Rep. kit valve system
Topstykke
27
Cylinder head
3 x Blindprop m. O-ring
28
3 x Blind plug w. O-ring
Rep. sæt vandtilgang
30
Rep. kit water inlet
Sugefi lter
31
Suction fi lter
Låsebøjle
36
Lock bracket
Låsebøjle
37
Lock bracket
O-ring
38
O-ring
Motor / pumpe
Motor / Pump
Motor / Pumpe
Moteur / pompe
Bezeichnung
Désignation
Kondensator
Condensateur
Ventilator
Ventilateur
Motor m. Taumelscheibe komplett
Moteur avec disque obl. compl.
Motor m. Taumelscheibe komplett
Moteur avec disque obl. compl.
Rep. satz Taumelscheibe
Kit de rép. disque oblique
Rep. satz Lager
Kit de rép. palier
Rep. satz Kolben
Kit de rép. piston
Rep. satz Ventil für S/S-Automatik
Kit, soupape marche/arrêt automatique
Gehäuse m. Schalter & Kabel
Boîte avec micro-switch & câble
Rep. satz Dichtungssystem
Kit de rép. système d'étanchéité
Rep. satz Ventilsystem
Kit de rép. système de soupape
Zylinderkopf
Culasse
3 x Blindpfropfen m. O-Ring
3 x Cache avec joint torique
Rep. satz Wassereinlaß
Kit de rép. entrée d'eau
Saugfi lter
Filtre d'aspiration
Verschlußbügel
Clips de maintien
Verschlußbügel
Clips de maintien
O-Ring
Joint torique
21
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the DYNAMIC Standard and is the answer not in the manual?
Questions and answers
The unit does not start
The Alto DYNAMIC Standard unit may not start due to the following reasons:
1. Machine not plugged in – Ensure the machine is properly plugged into a power source.
2. Defective socket – Try using a different socket.
3. Blown fuse – Replace the fuse and turn off other machines that may be overloading the circuit.
4. Defective extension cable – Try running the machine without the extension cable.
5. Low voltage or low temperature – Activate the trigger of the spray handle to check if the machine starts.
If the issue persists after these checks, further troubleshooting or professional service may be required.
This answer is automatically generated
My alto Kew dynamic 7400 keeps stop starting and won’t stay on permanently. I’m not sure if this an issue with the lance or the machine.
The Alto DYNAMIC Standard 7400 could be stopping and starting intermittently due to air in the inlet hose or pump, which causes the machine to pulsate. Letting the machine run can help remove the air. Other possible causes include a blown fuse, incorrect mains voltage, or the thermal sensor being activated.
This answer is automatically generated