Related Manuals for Speco O2VLB7
Summary of Contents for Speco O2VLB7
- Page 1 User Manual 2MP IP Camera O2VLB7 / O2VLB8 / O2VLD7 / O2VLD8 Please read this manual carefully before operating the unit and keep it for further reference...
- Page 2 IP Camera User Manual Important Safeguards and Warnings 1． ． ． ． Electrical safety All installation and operation here should conform to local electrical safety codes. Use a certified/listed 12VDC Class 2 power supply only. Please note: Do not connect two power supplying sources to the device at the same time; it may result in device damage! The product must be grounded to reduce the risk of electric shock.
-
Page 3: Regulatory Information
Statement This guide is for reference only. Product, manuals and specifications may be modified without prior notice. Speco Technologies reserves the right to modify these without notice and without incurring any obligation. Speco Technologies is not liable for any loss caused by improper operation. -
Page 4: Table Of Contents
IP Camera User Manual Table of Contents Regulatory Information ...................................... 3 Introduction ........................................ 1 Welcome ..........................................1 Web Access and Login ....................................2 LAN ................................................ 2 Live View ........................................3 Camera Configuration ....................................4 System Configuration ..........................................4 4.1.1 System Information ......................................... 4 4.1.2 Date and Time ......................................... -
Page 5: Introduction
Thank you for purchasing this network camera! Please read this manual carefully before operating the unit and retain it for future reference. Should you require any technical assistance, please contact Speco Technologies Technical Support. Main Features Built-in PoE (Power over Ethernet) -
Page 6: Web Access And Login
IP Camera User Manual 2 Web Access and Login The IP camera settings can be accessed via a web browser through the LAN web browser through the LAN. 2.1 LAN Access through IP Scanner Network connection: ① Make sure that the camera and the PC are connected that the camera and the PC are connected on the same local network. -
Page 7: Live View
IP Camera User Manual 3 Live View The window below will be shown after logging in. The following table describes the icons on the live view live view interface. Icon Description Description Icon Description Go to camera setup Go to camera setup Adjust image settings Stop/Start Stop/Start live view... -
Page 8: Camera Configuration
IP Camera User Manual 4 Camera Configuration Press the “Setup” button to go to the configuration interface. configuration interface. Note: Wherever applicable, press the “Save” button to save o save the settings. 4.1 System Configuration 4.1.1 System Information In the “System Information” interface, the system information of the information of the device is listed. -
Page 9: Users
IP Camera User Manual 4.1.3 Users To configure users, go to System -> Users. Other than admin, up to 6 additional users can be configured, with customizable access levels. Other than admin, up to 6 additional users can be configured, with customizable access levels. Other than admin, up to 6 additional users can be configured, with customizable access levels. -
Page 10: Image Configuration
IP Camera User Manual 4.2.2 Image Configuration In the Image Control interface shown below, various settings can be adjusted such as , various settings can be adjusted such as brightness, contrast, hue, saturation saturation, etc. IR-Cut Mode: Choose between Auto, Color Mode, and monochrome Mode Choose between Auto, Color Mode, and monochrome Mode. -
Page 11: Video Stream Setup
IP Camera User Manual 4.2.4 Video Stream Setup Go to Display Video Streaming as shown below. Resolution, frame rate, esolution, frame rate, etc. can be adjusted in this section. Two video streams can be adjustable. Resolution: The size of the image. FPS (frame rate): The higher the frame rate, the video is smoother the video is smoother. -
Page 12: Network Setup
IP Camera User Manual 4.3 Network Setup 4.3.1 Network Go to the Network Network interface shown below. Type: Choose between DHCP and Static. The device will be configured to DHCP by default. If set to static, enter the network info values in the fields. The device will be configured to DHCP by default. -
Page 13: Ddns
IP Camera User Manual Password: Enter the password of the sender’s email account. the password of the sender’s email account. Sender: Enter the sender’s email address as it would appear in the email. Enter the sender’s email address as it would appear in the email. Receiver 1/2/3: Enter up to 3 receiving email addresses Enter up to 3 receiving email addresses. -
Page 14: Rtsp
IP Camera User Manual 4.3.5 RTSP Go to Network->RTSP as shown below. Select “Enable” to enable the RTSP function. Note that RTSP streaming is used to stream the video to the NVR, so it is highly recommended to leave this Note that RTSP streaming is used to stream the video to the NVR, so it is highly recommended to leave this Note that RTSP streaming is used to stream the video to the NVR, so it is highly recommended to leave this enabled. -
Page 15: Snmp
IP Camera User Manual 4.3.7 SNMP To get camera status, parameters and alarm information and remotely manage the camera, the SNMP function To get camera status, parameters and alarm information and remotely manage the camera, the SNMP function can be used can be used. -
Page 16: Motion Setup
IP Camera User Manual 4.4 Motion Setup 4.4.1 Motion Detection Go to Alarm Motion to set up motion detection. Check “Enable” to activate motion based alarms. If Check “Enable” to activate motion based alarms. If unchecked, the camera will not send out any signals to trigger motion unchecked, the camera will not send out any signals to trigger motion-based recording to the NVR or the VMS, even if there is motion in the video. -
Page 17: Advanced Configuration
IP Camera User Manual 4.6 Advanced Configuration 4.6.1 Firmware Update Go to Advanced Firmware Update. In this interface, the camera firmware can be updated the camera firmware can be updated. Click the “Scan” button to select the location of the firmware file. ”... -
Page 18: Appendix
IP Camera User Manual Appendix Appendix 1 Troubleshooting IP Scanner does not show any device. Make sure that the PC that’s running IP Scanner is on the same local network as the devices. Internet Explorer cannot download ActiveX control. IE browser may be set up to block ActiveX. Follow the steps below. Open IE browser and then click Tools->Internet Options Select Security and then Custom Level Enable all the options under “ActiveX controls and plug-ins”.