Speco ONSIP O2D4 Owner's Manual
  1. Manuals
  2. Brands
  3. Speco Manuals
  4. Security Camera
  5. ONSIP O2D4
  6. Owner's manual

Speco ONSIP O2D4 Owner's Manual

Vandal resistant dome ip camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
O
N
S
I
P
O
2
D
4
O
w
n
e
r
O
N
S
I
P
O
2
D
4
O
w
n
e
r
ONSIP O2D4
'
'
s
M
a
n
u
a
l
s
M
a
n
u
a
l
Rev.1.3 (June,2013)
1

Advertisement

Table of Contents
loading

Related Manuals for Speco ONSIP O2D4

Summary of Contents for Speco ONSIP O2D4

  • Page 1 ’ ’ ONSIP O2D4 Rev.1.3 (June,2013)
  • Page 2 ’ ’ Directions Be careful not to cause any physical damage by dropping or throwing ONSIP O2D4. Especially keep the device out of reach from children. Do not disassemble ONSIP O2D4. No after service is assumed when disassembled. Use only the power adapter provided with ONSIP O2D4.

  • Page 3: Revision History

    ’ ’ Caution Any changes or modifications in construction of this device which are not explicitly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Revision History Date Revision Details May 13 , 2013 First manual revision creation.

  • Page 4: Table Of Contents

    Contents..................4 1. Introduction ................5 1.1. Overview ....................5 1.2. Specification ....................6 1.3. Applications of ONSIP O2D4 ................. 8 2. Product Description ..............9 2.1. Contents ....................9 2.2. Product Preview ..................9 2.3. Physical description .................. 10 2.4.

  • Page 5: Introduction

    It enables real time transmission of synchronized video of up to 1080p and audio data. Remote clients can connect to ONSIP O2D4 for the real time video/audio data through various client solutions running on PC, PDA or mobile phones. Real time 2-way communication is available through bidirectional audio communication feature.

  • Page 6: Specification

    Upgrade Firmware upgrade over IP network Administration Remote administration over IP network Web Viewer Simple viewing over internet explorer Client & Viewer Speco-NVR Standard VMS software Dynamic IP support DDNS support Supported Video/Audio stream encryption Security ID and Password protection...
  • Page 7 ’ ’ IP filtering for restricting administrative access for audio and bi-audio Sync to PC Synchronize to PC Time management Manual Manual time setting Internet Time Server Synchronize to Time Server Active-X SDK support HTTP Rev.1.3 (June,2013)

  • Page 8: Applications Of Onsip O2D4

    ’ ’ 1.3. Applications of ONSIP O2D4  Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities, military, etc.)  Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)  Teleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting ...

  • Page 9: Product Description

    2.1. Contents The product package contains followings: Contents Description Remarks ONSIP O2D4 IP camera ONSIP O2D4 main unit Tools and Mounting Screws Screws(M4x16L 4EA, 4x16L 4EA), L-wrench Software & User’s Guide Quick Reference Guide Quick installation guide 2.2. Product Preview...

  • Page 10: Physical Description

    ’ ’ 2.3. Physical description 2.3.1. External View Figure 2-1. External view of ONSIP O2D4 Figure 2-2. Connection Cable of O2D4 Rev.1.3 (June,2013)
  • Page 11 ’ ’ Figure 2-3. Adjustment knobs for the Camera Figure 2-4. 3 axis based camera position control (Manual adjustment of Pan, Tilt and Video rotation.) Rev.1.3 (June,2013)

  • Page 12: Functional Description

    ’ 2.4. Functional Description  DC 12V, 2A: Power input for supplying 12V DC power. Caution: If ONSIP O2D4 is powered by PoE, do not plug in DC Jack with active DC power into DC power connector.  MIC/LINE IN Connect external audio source or microphone.
  • Page 13 ’ ’ Figure 2-2 ALARM IN/OUT of ONSIP O2D4  RLY Out: Relay output is provided for connecting alarm devices or for remote on/off control of devices such as light. Relay is normal open and it will be closed upon alarm annunciation or remote on. The relay...
  • Page 14 A switch provided for returning the IP camera to factory default state. Open the dome cover to access the switch. Press the switch for a few seconds while power is applied. Figure 2-5. Factory Default Switch of ONSIP O2D4 Caution: Restoring the factory default will erase all settings.

  • Page 15: Getting Started

    Brief information for the initial operation of ONSIP O2D4 is provided in this chapter. 4.1. PC Requirement Audio/Video streaming data received from ONSIP O2D4 can be displayed or stored in a PC running client programs. Minimum requirement of the PC is described below:...

  • Page 16: Quick Installation Guide

    1) Prepare a PC to run programs for the installation and video connection (PC is needed to assign IP address to ONSIP O2D4) 2) In the case of using PoE, connect the PC and ONSIP O2D4 to the network using one of the following ways.
  • Page 17 ’ 2. Install Speco-NVR Speco-NVR is a multi-channel VMS program for the IP camera. Install Speco-NVR on remote PC to connect to these products. It is needed to assign connection information to Speco-NVR program before connection. Insert the CD provided with product into the PC and install Speco-NVR.
  • Page 18 ’ ’ Click on the field in (3) for sorting and rearranging the list. Select network mode that best suits from the drop down list in (5). You can choose either Static or ADSL and Auto (DHCP), respectively. If ADSL and Auto are selected, the fields in (6) are deactivated.
  • Page 19 3. Remote video connection to ONSIP O2D4 1) Connection through Web Viewer Web Viewer offers the simplest way of video connection to ONSIP O2D4. For video connection, enter the IP address of ONSIP O2D4 in the URL window of Internet Explorer as: Port 80 (default) can be [e.g.] Port 80...
  • Page 20 SAVE button. You can see the live video when you click the live view button as below. When you exit Speco-NVR, you have to input the ID/PW, admin/1234. Details for Speco-NVR can be found in [Speco-NVR User’s Guide].
  • Page 21 ’ ’ 4. Additional settings through connection to the Admin Page All parameters of the camera are factory default out of the box. For a more sophisticated target application, parameters need to be changed through the admin page. The admin page can be connected through ”http://IP_address:HTTP_port_number”/admin.htm ID and password of the administrator are required.

  • Page 22: Troubleshooting

    ’ ’ 4. Troubleshooting 5.1. No power is applied  In case of Standard PoE (Power over Ethernet) Power supply through standard PoE is possible only when the following conditions are met. 1. Standard PoE is supported on the product. 2.

  • Page 23: Cannot Connect To The Video

    ’ ’ 5.2. Cannot connect to the Video Check the status of the network connection through PING test. Try the following on your PC: Start > Run > Cmd > Ping IP address (Ex : Ping 172.16.42.51) If “Reply from ~”...

  • Page 24: Windows Vista Or Windows 7

    5.3. Windows Vista or Windows 7 Windows Vista and Windows 7 users need to configure UAC (User Access Control) and Privilege Level for proper recording and still video capture in Speco-NVR and Web Viewer. <Windows Vista> 1. UAC (User Access Control) configuration 1) Double-click “User Accounts”...
  • Page 25 ’ ’ <Windows 7> 1. UAC (User Access Control) configuration 1) Double-click “User Accounts” in control panel 2) Double-click “Change User Account Control setting” 3) Set to “Never notify” Rev.1.3 (June,2013)
  • Page 26 ’ ’ 2. Privilege Level Control 1) Select “NVR” icon on the desktop 2) Click right mouse button and select “properties” 3) Check “Privilege Level” in “Compatibility” tab Rev.1.3 (June,2013)

  • Page 27: Technical Assistance

    ’ ’ 5.4. Technical Assistance If you need any technical assistance, please contact your dealer. For immediate service please provide the following information. 1. Model name 2. MAC address and Registration number 3. Purchase date 4. Description of the problem 5.

Table of Contents