Eswood CI-3B Equipment Manual
  1. Manuals
  2. Brands
  3. Eswood Manuals
  4. Dishwasher
  5. CI-3B
  6. Equipment manual
Eswood CI-3B Equipment Manual

Eswood CI-3B Equipment Manual

Compact glass washer
Hide thumbs

Advertisement

Table of Contents

EQUIPMENT MANUAL
FOR
CI-3B COMPACT GLASS WASHER
JUNE 2011

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CI-3B and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Eswood CI-3B

Summary of Contents for Eswood CI-3B

  • Page 1 EQUIPMENT MANUAL CI-3B COMPACT GLASS WASHER JUNE 2011...

  • Page 2: Table Of Contents

    PAGE No. Important: Prior to Installation General Description Technical Specifications Installation Initial Start-up Procedure Washing Operation Shutdown and Maintenance Trouble Shooting 11-12 CI-3B Export Model Spare Parts 14-15 Wiring Diagram Spare Parts & Service ESWOOD OPERATING MANUAL CI-3B June 2011...

  • Page 3: Important: Prior To Installation

    (Note: Travel time not covered by warranty) In no event will ESWOOD AUSTRALIA be liable for loss of facilities or other property and such things as, but not limited to, additional labour costs, loss of revenue or anticipated profits, and other damages of any kind whether direct, indirect, incidental or consequential.

  • Page 4: General Description

    For the hustle and bustle of a cocktail or lounge bar, the CI-3B can be plumbed to provide a cold cycle after the final sanitising rinse, and this would become a permanent part of the washing cycle.

  • Page 5: Technical Specifications

    8 Litres per cycle Hot and Cold water usage Litres hot water 3 Litres cold water Wash/Rinse Temperature C to 85 Final Cycle Temperature Cold: 20 Hot: 65 Electrical Usage Electrical 240V, 50Hz, 1 phase, 12.5 Amps ESWOOD OPERATING MANUAL CI-3B June 2011...

  • Page 6: Installation

    Note that all electrical work is to be done in accordance with the rating plate on the lower panel. The CI-3B comes standard with a detergent injection system already set up. Purge the rinse cylinder of air by opening water supplies to the machine, switching the machine on and putting it through three or four cycles.
  • Page 7 (with a screwdriver) so that it aligns with the silver line on the set point. (refer figure 2.) Refit the lower panel. SET POINT OVERIDING THERMOSTAT FIGURE 1 SET POINT (HOLE) CYCLING THERMOSTAT ON RINSE CYLINDER FIGURE 2 ESWOOD OPERATING MANUAL CI-3B June 2011...

  • Page 8: Initial Start-Up Procedure

    Note that the CI-3B has the detergent pump set up to handle undiluted detergent. Do not dilute detergent. 4. When the “READY 82 C” light is on, press the Red button for an all Hot cycle or Blue button for a Hot cycle followed by a Cooling cycle.

  • Page 9: Washing Operation

    “CYCLE” light is illuminated. (refer figure 2.) 5. Occasionally check that the drain outlet is free from debris such as paper, toothpicks and sliced fruit. BLUE BUTTON RED BUTTON RED LIGHT ORANGE LIGHT TOGGLE SWITCH RED LIGHT FIGURE 2. ESWOOD OPERATING MANUAL CI-3B June 2011...

  • Page 10: Shutdown And Maintenance

    Clean the exterior of the machine with a damp sponge. Do not pass water over the electrical controls and avoid abrasive or strong detergents. Check for leaks and ensure that the arms rotate freely. Leave the door open to allow the machine to air. ESWOOD OPERATING MANUAL CI-3B June 2011...

  • Page 11: Trouble Shooting

    (b) Check for foreign matter in wash arm jets. Clean if necessary. (c) Check that glasses to be washed are correctly placed in racks. (d) Check temperature of rinse cylinder. If incorrect check thermostat setting and heating element. ESWOOD OPERATING MANUAL CI-3B June 2011...
  • Page 12 (d) Check that the line strainer is not partially blocked. If so, remove and clean filter. Insufficient rinse (a) Ensure that temperature of temperature incoming water supply is at least 65 ESWOOD OPERATING MANUAL CI-3B June 2011...

  • Page 13: Ci-3B Export Model

    CI-3B E XPORT MODEL The CI-3B supplied for export differs from Australian models as follows: An analog temperature gauge is provided as standard on all export machines. ESWOOD OPERATING MANUAL CI-3B June 2011...

  • Page 14: Spare Parts

    PARE ARTS ESWOOD OPERATING MANUAL CI-3B June 2011...
  • Page 15 OVER-RIDE THERMOSTAT SS-131 RINSE TANK THERMOSTAT SS-161 PUSH BUTTON-RED SS-160 PUSH BUTTON – GREEN EP-132 TRANI LAMP – RED EP-133 TRANI LAMP – AMBER SS-147 TOGGLE SWITCH EP-211 ELEMENT B-1317 RINSE CYLINDER B-1304-1 PANEL DECAL ESWOOD OPERATING MANUAL CI-3B June 2011...

  • Page 16: Wiring Diagram

    IRING IAGRAM ESWOOD OPERATING MANUAL CI-3B June 2011...

  • Page 17: Spare Parts & Service

    (Applicable to landline only charges apply for calls made from a Mobile Phone) 1800 013 123 This number will automatically access your nearest State office, or the technician on duty if after hours. After hours charges apply. ESWOOD OPERATING MANUAL CI-3B June 2011...

Table of Contents