Download
Share
Print this page
Metrohm 7010 TOC User Manual
  1. Manuals
  2. Brands
  3. Metrohm Manuals
  4. Measuring Instruments
  5. 7010 TOC
  6. User manual

Metrohm 7010 TOC User Manual

Hide thumbs

Advertisement

Quick Links

Download this manual

Advertisement

loading
Need help?

Need help?

Do you have a question about the 7010 TOC and is the answer not in the manual?

Questions and answers

Related Manuals for Metrohm 7010 TOC

Summary of Contents for Metrohm 7010 TOC

  • Page 6 Metrohm Applikon...
  • Page 10 WARNING: UV lamp power supply reaches an ignition voltage up to 3000 volts; do not operate any service activity without removing instrument power cord It will be user’s responsability to check and garantee periodically the perfect efficiency analyzer’s grounding.
  • Page 12 EN 60204 WARNING:...
  • Page 14 701 0 TOC...
  • Page 15 LIQUIDS enclosure ELECTRICAL enclosure...
  • Page 16 ref. page 1 9) 1 4) 1 0) 1 0) 1 2) 1 3)
  • Page 18 REDUCING REAGENT FLOW DIAGRAM...
  • Page 21 1 0) 1 0) 1 4) 11 )
  • Page 22 1 2) 1 0) 1 2)
  • Page 23 1 3)
  • Page 24 CAUTION : do not overtighten or twist gas dryer ends when installing or servicing, as this will restrict the airflow.
  • Page 27 M1 M2...
  • Page 28 1 0) 1 0)
  • Page 29 1 3) 701 0 TOC 701 0 TOC...
  • Page 31 701 0 TOC 701 0 TOC...
  • Page 32 ATTENTION: depending on the sample chemical composition, WARNING: the sample drain of the analyzer must be at its oxidation can generate hazardous gases. In these cases it’s ambient pressure with no restriction or counterpressure. strictly necessary to provide a safety system to allow waste Please verify that this condition has been strictly respected gases vent to the atmosphere during installation.
  • Page 33 ALWAYS ISOLATE POWER BEFORE SERVICING...
  • Page 34 701 0 TOC USER CONNECTIONS 701 0 TOC...

  • Page 39: Important Note

    During analyzer’s initial start-up it is necessary to decide to confirm cleaning as the automatic option programmed as default option) or change to validation or calibration. Metrohm Applikon For ex. : if autocleaning is the automatic function enabled, autocalibration and autovalidation will be automatically disabled.
  • Page 42 The main screen displays: (min. press 2 secs) (min. pres. 2 secs)
  • Page 43 The main screen displays:...
  • Page 44 BASIC ADVANCED SERVICE BASIC ADVANCED password: 1111 SERVICE Metrohm Applikon...
  • Page 45 SAMPLE OK / NO): RELAY A OFF / ON): OUT EXTRA RLY OFF / ON): CARRIER flow : REAGENT TANKS LEVEL: CO2 conc: VALIDATION:...
  • Page 46 ppm zerogas: ppm liq. zero: ppm baseline mg/l standard: ppm span gas:...
  • Page 47 ZEROGAS ZEROGAS ZEROGAS NDIR ZEROGAS NDIR ZEROGAS...
  • Page 48 LIQUID ZERO LIQUID ZERO PRESS TO CAL...

  • Page 49: Manual Cal

    CALIBRATION MANUAL CAL PRESS TO CAL...
  • Page 50 AUTOCAL 11 ) NDIR...
  • Page 51 ZeroGas time OFF) Extra Relay OFF) Extra Relay COND delay min AUTO time OFF)
  • Page 52 FLOW MIN ZEROGAS MAX VAL TOLERANCE ALARM mg/l Analyzer mg/l CO2 ppm Range Factor Relay A Relay B OFF) DATE : 0 corresponds to 4 mA 50 corresponds to 12 mA (day, month, year 100 corresponds to 20 mA TIME : ZEROGAS ppm ZEROLIQ ppm (in hours/minutes 24 hours format)

  • Page 53: Clear All

    CLEAR FIRST DAY CLEAR ALL DTLG ON/OFF ALARM LOG...

  • Page 54: Reset Time

    TIME EVENT RESET TIME...
  • Page 64 Warning: Sodalime granules) is a strong oxidizer and should be handled with extreme care.
  • Page 65 WARNING – UV lamps may be hot if recently powered. Handle with suitable gloves.
  • Page 66 WARNING – UV lamps may be hot if recently powered. Handle with suitable gloves.
  • Page 67 701 0 TOC...
  • Page 68 701 0 TOC Metrohm Applikon...
  • Page 72 IMPORTANT WARNING: always add acid to water and never the reverse. Note: when the quantity of TIC in the sample is high it is suggested to use a 20 phosphoric acid solution.
  • Page 74 Metrohm Applikon Cleaning Solution Metrohm Applikon...
  • Page 75 IMPORTANT WARNING: always add acid to water and never the reverse.
  • Page 76 701 0 TOC...