Table of Contents
Advertisement
Quick Links
MODEL S4F
SUBMERSIBLE
SOLIDS HANDLING PUMP
INSTALLATION AND SERVICE MANUAL
NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible
party who maintains the system.
Item # E-03-306 | Part # 5625-306-1 | © 2012 Pentair Pump Group, Inc. | 10/25/12
Advertisement
Table of Contents
Related Manuals for Pentair Hydromatic S4F
Summary of Contents for Pentair Hydromatic S4F
- Page 1 NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible party who maintains the system. Item # E-03-306 | Part # 5625-306-1 | © 2012 Pentair Pump Group, Inc. | 10/25/12...
-
Page 2: General Information
CALIFORNIA PROPOSITION without damage but the seal General 65 WARNING: should be checked immediately after failure is indicated. Information This product and related accessories contain chemicals known to the State of N OTE: Failure to install such a Thank you for purchasing your California to cause cancer, birth device negates all warranties by Hydromatic pump. - Page 3 Sump Level Control: Triplex systems use four controls: level with the sump level never one set at turn-off, one set at turn- reaching the alarm level. This is Sump level is controlled by on for one pump, one set at turn- particularly true in cases of low Hydromatic float switch controls.
-
Page 4: Installation Instructions
otherwise water will return to the Installation sump and cause short cycling of the pump. Pump Instructions NEMA 4 Junction Box: Installing Pump in Sump: a main circuit breaker for each (Optional) pump, a magnetic starter with Before installing pump in sump If electrical control panel is to overload protection for each lay it on side and turn impeller... -
Page 5: Pump Operation
Installing Float Switch Controls: Making Electrical Connections: Pump The controls are supported by a All electrical wiring must be Operation mounting bracket that is attached in accordance with local code, to sump wall or cover or to the and only competent electricians NEMA 4 junction box. -
Page 6: Pump Maintenance
Servicing Instructions: 4. Set assembly on bench and Pump remove connection box. When box is lifted off, Operation IMPORTANT: Read connection wires to motor instructions before replacing will be exposed. These wires any parts. will probably be burned, but as sometimes a high leg each wire is tagged with a will exist. - Page 7 Replacing Seals and Bearings: additional instructions on 10. Use bearing puller to remove replacing seals and bearings. bearings. Replace with new 1. Drain all oil from motor Remember to reinstall the bearings. Press only on chamber and seal chamber upper bearing load spring. inner face of bearing when as described.
-
Page 8: Pump Troubleshooting
Pump operates with selector on pump side of all valves. Pump switch in Hand position but will Multiply gauge pressure in not operate in Auto position. pounds by 2.31 to get head Troubleshooting in feet. 1. This indicates trouble in the float level control or the 5. -
Page 9: Parts List
Parts List Ref. Part Part Ref. Part Part Ref. Part Part Description Qty. Description Qty. Description Qty. 00853-000-1 Wire Connector (230V 3ø) 00975-012-1 Snap Ring 07773-013-5 Rotor w/Shaft 3/4 –1 HP All 3ø, 1150 RPM 00557-000-1 Wire Connector (460V 3ø) 04916-000-1 Upper Seal, Carbon/Ceramic 00865-014-5... - Page 10 40 39 18 19 20 21...
- Page 11 THIS PAGE INTENTIONALLY LEFT BLANK...
-
Page 12: Standard Limited Warranty
Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps. under no circumstance will Pentair Hydromatic be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Hydromatic service facility.
Need help?
Do you have a question about the Hydromatic S4F and is the answer not in the manual?
Questions and answers