Table of Contents
Advertisement
MODELS
S4L(X
), S4LRC/S4LVX
*
S4B(X
), S4K(X
*
S6L(X
), S6A(X
*
Used in Hazardous Locations Class I, Division 1
*
SUBMERSIBLE
SOLIDS HANDLING PUMPS
INSTALLATION AND SERVICE MANUAL
For use with product built with USEM motor.
NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible
party who maintains the system.
Item # E-03-491 | Part # 5625-491-1 | © 2013 Pentair Pump Group, Inc. | 09/09/13
), H4Q(X
*
) and S8F(X
*
,
*
),
*
)
*
(*Hazardous Location
Motor End)
Advertisement
Table of Contents
Related Manuals for Pentair HYDROMATIC S4L
Summary of Contents for Pentair HYDROMATIC S4L
- Page 1 NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible party who maintains the system. Item # E-03-491 | Part # 5625-491-1 | © 2013 Pentair Pump Group, Inc. | 09/09/13...
-
Page 2: General Information
Heat Sensors: enters the chamber through the General first seal, the electrode will be All motors have heat sensor units Information energized and a signal will be embedded in the motor winding transmitted to the sensing unit This manual contains important to detect excessive heat. - Page 3 Two pumps operate together only the alarm will signal only if provide appropriate con trol circuit if sump level rises to the third the override level is exceeded. and alarms. or override control. The override However, some engineers prefer Overload Heaters: control also brings on the second to have the alarm level set below pump in case of failure of the first...
-
Page 4: Pump Installation
For installation of Hydromatic If an alarm system is used, this Pump sup plied level con trols refer to control is usually set about 6 inches your sys tems installation and Installation above the override control. service manual. Installing Pump in Sump: Making Electrical Connections: NEMA 4 Junction Box Before installing pump in sump,... -
Page 5: Pump Maintenance
the field by any reliable motor notice operation. If pump is nameplate, not necessarily by motor service shop. Any pump, in horsepower. The warranty on all noisy and vibrates, rotation warranty, must be returned to the three phase submersible motors is is wrong. - Page 6 Replacing Seals and Bearings: wire must be dis con nect ed reinstall the upper bearing load spring. before housing is com plete ly 1. Drain all oil from motor removed. 9. Before replacing stator housing chamber and seal chamber 4. Set assembly on bench and be sure outside lock screw is in as described.
-
Page 7: Pump Troubleshooting
IMPORTANT: Do not use NOTE: Any time the seal is Pump does not deliver proper capacity. any of the old seal parts. disturbed, it must be replaced. Replace with all new seals. 1. Discharge gate valve may Pump 11. Thoroughly clean all castings partially closed before replacing seals. -
Page 8: Wet End Components
Wet End Components S4LVX S4L(X) S4LRC S4B(X) H4Q(X) S4K(X) S6L(X) S6A(X) S8F(X) - Page 9 Wet End Parts List For use with product built with USEM motor. Item S4LRC S4LRC/ Description S4B(X) S4L(X) S6A(X) S6L(X) S8F(X) S4K(X) H4Q(X) 3450 RPM S4LVX SCREW – HHC 5/8-11 UNF x 1-1/4 005700181 005700181 005700181 005700181 005700181 005700181 005700181 005700181 005700181 019450001...
- Page 10 Standard Location S4L, S4LRC, S4B, S4K, H4Q, S6L, S6A and S8F Motor End Components...
-
Page 11: Motor Parts List
Standard Location S4L, S4LRC, S4B, S4K, H4Q, S6L, S6A and S8F Motor End Parts List For use with product built with USEM motor. Ref. Part Part Ref. Part Part Ref. Part Part Description Qty. Description Qty. Description Qty. 19101A010 SCREW – CAP HEX 3/8 SST x 1 029210011 SCREW –... -
Page 12: Hazardous Location
Hazardous Location S4LX, S4LVX, S4BX, S4KX, H4QX, S6LX, S6AX and S8FX Motor End Components... - Page 13 Hazardous Location S4LX, S4LVX, S4BX, S4KX, H4QX, S6LX, S6AX and S8FX Motor End Parts List For use with product built with USEM motor. Ref. Part Part Ref. Part Part Ref. Part Part Description Qty. Description Qty. Description Qty. 001500191 0-RING 1/8 x 6.734 I.D. 005680071 SCREW –...
- Page 14 Hazardous Location S4LX, S4LVX, S4BX, S4KX, H4QX, S6LX, S6AX and S8FX Motor End Parts List (Continued) For use with product built with USEM motor. 4-Pole 1750 RPM 4Pole 1750 RPM 10 hp 10 hp 10 hp 10 hp 15 hp 15 hp 15 hp Item...
-
Page 15: Wiring Diagrams
Wiring Diagrams PROBE TEST RESISTOR ON HAZARDOUS LOCATION ONLY – PROBE TEST RESISTOR PROBE TEST RESISTOR ON HAZARDOUS LOCATION ONLY ON HAZARDOUS LOCATION ONLY – –... - Page 16 Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps. under no circumstance will Pentair Hydromatic be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Hydromatic service facility.