Menu Operation Section; Level Adjustment Knob; Key Inhi Switch - Sony HDW-S280 Operation Manual

Adjustment knob Recording
channel
REC LEVEL 2 Channel 2
PB LEVEL 1 Channel 3
PB LEVEL 2 Channel 4
e R/P LEVEL CTL switch
VAR: Enables adjustment with the PB LEVEL adjustment
knobs or REC LEVEL adjustment knobs while you
view the audio level meter in E-E mode.
PRESET: Presets to fixed levels. Levels cannot be
adjusted with the PB LEVEL adjustment knobs or
REC LEVEL adjustment knobs.
For Switching to E-E mode, see " To monitor in E-E
mode" on page 16.
f LEVEL adjustment knob
Adjusts the volume of the headphones connected to the
PHONES jack.
g PHONES (headphones) jack
Connect headphones.
h REC INHI switch and indicator
ON: Recording on the tape is inhibited, regardless of the
state of the cassette's erasure prevention plug. The
REC INHI indicator lights.
OFF: Recording on the tape is enabled when the cassette's
erasure prevention plug is set to the original position.
i KEY INHI switch
When this switch is set to ON, the functions of the buttons
selected with setup menu item 118 are inhibited.
For details on setup menu item 118, see page 66.
j Cassette compartment
Insert a cassette here.
k EJECT button
Press to eject the cassette. The cassette mark in the display
window flashes while the cassette is being ejected.
l REMOTE button
Selects the operation mode of this unit.
When the button is not lit, the unit is controlled from the
front panel of this unit. Normally use this status.
When the button has been pressed and is lit, this unit is
controlled from the device connected to the REMOTE 9P
connector. In this case, all VTR operations using this unit's
front panel are disabled except those of the STOP and
EJECT buttons.
When two HDW-S280 units are connected, press this
button on the player VTR to make it lit.
14
Front Panel
You can determine which tape transport buttons on the
Playback
front panel are to be enabled when the REMOTE button is
channel
lit with setup menu item 006.
Channel 4
Channel 1
For details on setup menu item 006, see page 63.
Channel 2

2-1-1 Menu Operation Section

6 SHIFT button
a Function buttons
Select and set menu items displayed in the display window.
b Display window
Displays menus, audio level meters, and data such as time
data or meta-data. The DISPLAY button let you switch to
the video monitor display.
For details, see "2-1-3 Display Window" on page 16.
c MENU button
Displays a setup menu item in the time data display area of
the display window.
For details on the setup menu operations, see "9-2 Setup
Menu Operations" on page 60.
d DISPLAY button
Switches the operation display to the video monitor display
and vice versa.
e RESET button
Resets the CTL data displayed in the display window or the
initial value of the timecode generator.
f SHIFT button
Switches between functions for any button with two
functions.
1 Function buttons
2 Display window
CHARACTR
EMPH EMPH EMPH EMPH INPUT : ANA
ON
CH1 IN :
0 0
PB/EE
CH2 IN :
–10 –10
PB
OUT :
–20 –20
CONFI
MONI L :
ENABLE –30 –30
MONI R :
–40 –40
CTL/TC
1 2 3 4 DOLBY NR
TC
59.94i SDI ASMBL CONFI ON RECORDER
ASSEMBLE
LTC
OFF DF VITC LTC EXT-LTC R-RUN REM:00
TCG SET
00:00:00:00.
HOME
SHIFT
PAGE
HOME
7 PAGE/HOME button
3 MENU button
4 DISPLAY
button
5 RESET
button
MULTI CONTROL
DISPLAY
HD
MENU
–60
COND
–4
PUSH
+4 RESET
PITCH CTL
1
BANK 2
2
D-STOP
P ROLL
M
8 MULTI CONTROL knob