Sony HDW-S280 Operation Manual page 77

Item Item name
number
901 VIDEO OUTPUT DATA
920 SD-SDI RP188 ATC
CONTROL
921 ASPECT FLAG
930 DOWN CONVERTER MODE
(DC)
931 DOWN CONVERTER
LETTER BOX MODE (DC)
932 H CROP POSITION (DC)
934 CROSS COLOR (DC)
935 DETAIL GAIN (DC)
936 LIMITER (DC)
937 CRISP THRESHOLD (DC)
938 LEVEL DEPEND
THRESHOLD (DC)
939 H DETAIL FREQUENCY (DC) Adjust the down-converter image enhancer. Set the central frequency for edge
940 H/V RATIO (DC)
941 GAMMA LEVEL (DC)
942 V FILTER SELECT
Items 900 to 999: Settings for digital processing
Settings
Set the bit length for SD-SDI video output data.
8bit: Set the bit length to 8 bits.
[10bit]: Set the bit length to 10 bits.
It is recommended that you select the optimal setting for the device to which you are
going to connect this unit.
Select whether or not to add information to the SDI output.
OFF: Select whether to add (ON), or not (OFF).
[ON]: Add RP-188 timecode data.
Add the 16:9/Squeeze identification signal specified by ARIB TR-B17 to the down-
converted SD output when an HDCAM tape is played. When an SD tape is played,
the 16:9/Squeeze identification signal is detected, and switching the up-converter
mode is set.
[OFF]: The 16:9/Squeeze identification signal is not added to the down-converted
SD output from the HD signal. When an SD tape is played, the up-converter
mode depends on the setting for setup menu item 950 independent of the
existence of the identification signal on the tape.
ON: The 16:9/Squeeze identification signal is added to the down-converted SD
output in squeeze mode from the HD signal. When an SD tape is played, the
identification signal on the tape is detected, and the up-converter mode is
automatically selected. If the identification signal on the tape is not detected, the
up-converter mode depends on the setting for setup menu item 950.
Select the down-converter mode.
[CROP]: Select the edge-crop mode.
L-BOX: Select the letter box mode.
SQUEZ: Select the squeeze mode.
Select the aspect ratio of the down-converter output when menu item 930 is set to
LETTER BOX.
[16:9]: Set the aspect ratio of the HD-SD converter output to 16:9.
14:9: Set the aspect ratio of the HD-SD converter output to 14:9.
13:9: Set the aspect ratio of the HD-SD converter output to 13:9.
Adjust the H-crop (the horizontal position when cropping in the edge crop mode) of
the down converter output when menu item 930 is set to EDGE-CROP.
–120 to [0] to 120
Adjust the down-converter cross color.
0 to [8] to 15
Adjust the down-converter image enhancer, the sharpness of edge emphasis.
0 to [20H] to 7FH
Adjust the down-converter image enhancer, the maximum detail level added to
emphasize the original signal.
0 to [20H] to 3FH
Adjust the down-converter image enhancer, the threshold amplitude at which low
amplitude signals are not emphasized.
[0] to FH
Adjust the down-converter image enhancer. Set the luminance range for edge
enhancement.
0 to [8] to FH
enhancement.
2.6MHz to 3.4MHz to [3.9MHz] to 4.6MHz
Adjust the down-converter image enhancer. Set the horizontal/vertical ratio for edge
enhancement.
0 to [3] to 7
Adjust the down-converter image enhancer, the slope of the correction curve.
0 to [80H] to 100H
Set the vertical interpolation filter coefficient for down-converter output.
The vertical resolution increases as the setting grows larger.
[1] to 3
Items in the Extended Setup Menu
77