Lantech IGS-2404 User Manual
  1. Manuals
  2. Brands
  3. Lantech Manuals
  4. Switch
  5. IGS-2404
  6. User manual

Lantech IGS-2404 User Manual

4 10/100/1000t + 4 10/100/1000t/dual speed sfp l2 managed industrial switch w/ pro-ring
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
4 10/100/1000T + 4 10/100/1000T/Dual
Speed SFP L2 Managed Industrial Switch
w/ Pro-Ring
IGS-2404
User Manual

Advertisement

Table of Contents
loading

Related Manuals for Lantech IGS-2404

Summary of Contents for Lantech IGS-2404

  • Page 1 4 10/100/1000T + 4 10/100/1000T/Dual Speed SFP L2 Managed Industrial Switch w/ Pro-Ring IGS-2404 User Manual...

  • Page 2: Table Of Contents

    Content Overview............. 1 Introduction .............. 1 Features ..............4 Packing List.............. 6 Safety Precaution............. 6 Hardware Description ......... 7 Front Panel............... 7 Top View ..............8 Wiring the Power Inputs ........... 8 LED Indicators............9 Ports............... 10 Cabling ..............11 Mounting Installation ........
  • Page 3 Installation Steps............ 18 X-Ring Application..........19 Coupling Ring Application ........20 Dual Homing Application........21 Console Management ........23 Connecting to the Console Port ......23 Pin Assignment ............23 Login in the Console Interface ....... 24 CLI Management............ 25 Commands Level .............
  • Page 4 Port Mirroring Commands Set.......... 42 802.1x Commands Set............. 43 TFTP Commands Set ............45 SystemLog, SMTP and Event Commands Set ....46 SNTP Commands Set............48 Pro-ring Commands Set........... 49 Web-Based Management......... 50 About Web-based Management ......50 Preparing for Web Management ......50 System Login ............
  • Page 5 System Event Log - SMTP Configuration ....59 System Event Log - Event Configuration ....61 Fault Relay Alarm........... 63 SNTP Configuration ..........63 IP Security.............. 66 User Authentication..........67 Port Statistics ............68 Port Control ............69 Port Trunk .............. 70 Aggregator setting............
  • Page 6 SNMP Configuration ..........83 System Configuration............84 Trap Configuration ............85 SNMPV3 Configuration ............ 86 QoS Configuration..........89 QoS Policy and Priority Type ........... 89 Port Base Priority ............. 90 COS Configuration ............91 TOS Configuration ............91 IGMP Configuration..........91 Pro-Ring System ............

  • Page 7: Overview

    Overview Introduction To create reliability in your network, the 4 10/100/1000T + 4 SFP Managed Industrial Switch comes equipped with a proprietary redundant network protocol:Pro-Ring provides users with an easy way to establish a redundant Ethernet network with ultra high-speed recovery time less than 10 ms.
  • Page 8 High-Speed Transmissions The 4 10/100/1000T + 4 SFP Managed Industrial Switch includes a switch controller that can automatically sense transmission speeds (10/100/1000 Mbps). The RJ-45 interface can also be auto-detected, so MDI or MDI-X is automatically selected and a crossover cable is not required.
  • Page 9 The operating temperature of the 4 10/100/1000T + 4 SFP Managed Industrial Switch is between -20 ~ 60 ℃. With such a wide range, you can use the 4 10/100/1000T + 4 SFP Managed Industrial Switch in some of the harshest industrial environments that exist. Easy Troubleshooting indicators make...

  • Page 10: Features

    Features Provides 4 x 10/100/1000Base-T Mbps Ethernet ports Provides 4 x SFP (mini-GBIC) port (support 100/1000 Dual Mode) Supports full/half duplex flow control Supports auto-negotiation Supports MDI/MDI-X auto-crossover Supports Packet Buffer up to 1Mbits Supports MAC Address up to 8Kbytes Supports surge (EFT) protection 3,000 V for power line Supports 4,000 V...
  • Page 11 Broadcast/Multicast Packet Filter Control Port Mirror: Monitor traffic in switched networks. TX Packet only RX Packet only Both of TX and RX Packet System Event Log System Log Server/Client SMTP e-mail Alert Relay Alarm Output System Events Security Port Security: MAC address entries/filter IP Security: IP address security management to prevent unauthorized intruder Login Security: IEEE802.1X/RADIUS...

  • Page 12: Packing List

    Packing List 1 x 4 10/100/1000T + 4 SFP Managed Industrial Switch 1 x User Manual 2 x Wall Mounting Bracket and Screws Safety Precaution Attention IF DC voltage is supplied by an external circuit, please use a protection device on the power supply input.

  • Page 13: Hardware Description

    Hardware Description In this paragraph, we will introduce the Industrial switch’s hardware spec, port, cabling information, and wiring installation. Front Panel The Front Panel of 4 10/100/1000T + 4 SFP Managed Industrial Switch is shown as below. Standard Model -E Model...

  • Page 14: Top View

    Top View The top panel of 4 10/100/1000T + 4 SFP Managed Industrial Switch is equipped one terminal block connector of two DC power inputs. Top panel of the 4 10/100/1000T + 4 SFP Industrial Switch Wiring the Power Inputs Please follow the steps below to insert the power wire.

  • Page 15: Led Indicators

    Tighten the wire-clamp screws for preventing the wires from loosing. Note The wire gauge for the terminal block should be in the range between 12~ 24 AWG. LED Indicators There are few LEDs display the power status and network status located on the front panel of 4 10/100/1000T + 4 SFP Industrial Switch, each of them has its own specific meaning as tabled below.

  • Page 16: Ports

    Not connected to network Connected to network P1 ~ P4 Green Flashing Networking is active at speed of 100Mbps Upper LED Not connected to network P1 ~ P4 Connected to network at speed of 1000Mbps Green (Lower LED) Not connected to network LED indicators of 4 10/100/1000T + 4 SFP Managed Industrial Switch Ports RJ-45 ports (Auto MDI/MDIX): The RJ-45 ports are auto-sensing for 10Base-T,...

  • Page 17: Cabling

    Receive Data plus (RD+) Transmit Data plus (TD+) Receive Data minus (RD-) Transmit Data minus (TD-) Transmit Data plus (TD+) Receive Data plus (RD+) Transmit Data minus (TD-) Receive Data minus (RD-) Straight Through Cable Schematic Cross Over Cable Schematic Cabling Use the four twisted-pair, Category 5e or above cabling for RJ-45 port connection.
  • Page 18 Transceiver to the SFP module Transceiver Inserted...
  • Page 19 Second, insert the fiber cable of LC connector into the transceiver. LC connector to the transceiver To remove the LC connector from the transceiver, please follow the steps shown below: First, press the upper side of the LC connector from the transceiver and pull it out to release.
  • Page 20 Second, push down the metal loop and pull the transceiver out by the plastic part. Pull out from the SFP module...

  • Page 21: Mounting Installation

    Mounting Installation DIN-Rail Mounting The DIN-Rail is screwed on the industrial switch when out of factory. If the DIN-Rail is not screwed on the industrial switch, please see the following figure to screw the DIN-Rail on the switch. Follow the below steps to hang the industrial switch. Step 1: Use the screws to screw on the DIN-Rail on the industrial switch.

  • Page 22: Wall Mount Plate Mounting

    First, insert the top of DIN-Rail into the track. Then, lightly push the button of DIN-Rail into the track. Check the DIN-Rail is tightly on the track. To remove the industrial switch from the track, reverse the steps above. Wall Mount Plate Mounting Follow the steps as below to mount the industrial switch with wall mount plate.
  • Page 23 Use the hook holes at the corners of the wall mount plate to hang the industrial switch on the wall. To remove the wall mount plate, reverse steps above. Use screws to screw the wall mount plate on the rear side...

  • Page 24: Hardware Installation

    Hardware Installation In this paragraph, we will describe how to install the 4 10/100/1000T + 4 SFP Industrial Switch and the installation points for the attention. Installation Steps Unpacked the Industrial switch packing. Check the DIN-Rail is screwed on the Industrial switch. If the DIN-Rail is not screwed on the Industrial switch.

  • Page 25: X-Ring Application

    Power on the Industrial switch. How to wire the power; please refer to the Wiring the Power Inputs section. The power LED on the Industrial switch will light up. Please refer to the LED Indicators section for meaning of LED lights. Prepare the twisted-pair, straight through Category 5e/above cable for Ethernet connection and SFP transceiver with LC cable for fiber connection.

  • Page 26: Coupling Ring Application

    Coupling Ring Application In the network, it may have more than one X-Ring group. Using the coupling ring function can connect each X-Ring for the redundant backup. It can ensure the transmissions between two ring groups not to fail. The following figure is a sample of coupling ring application.

  • Page 27: Dual Homing Application

    Dual Homing Application Dual Homing function is to prevent the connection loss from between X-Ring group and upper level/core switch. Assign two ports to be the Dual Homing port that is backup port in the X-Ring group. The Dual Homing function only works when the X-Ring function is active.

  • Page 29: Console Management

    Console Management Connecting to the Console Port The supplied cable which one end is RS-232 connector and the other end is RJ-45 connector. Attach the end of RS-232 connector to PC or terminal and the other end of RJ-45 connector to the console port of switch. The connected terminal or PC must support the terminal emulation program.

  • Page 30: Login In The Console Interface

    Login in the Console Interface When the connection between Switch and PC is ready, turn on the PC and run a terminal emulation program or Hyper Terminal and configure its communication parameters to match the following default characteristics of the console port: Baud Rate: 9600 bps Data Bits: 8 Parity: none...

  • Page 31: Cli Management

    Console login interface CLI Management The system supports the console management – CLI command. After you login to the system, you will see a command prompt. To enter CLI management interface, type in ‘enable’ command. CLI command interface...

  • Page 32: Commands Level

    The following table lists the CLI commands and description. Commands Level Access Exit Modes Prompt About This Mode1 Method Method The user commands available at the user level are a subset of Begin a those available at the Enter logout User EXEC session with switch>...

  • Page 33: Commands Set List

    privileged EXEC mode. Enter the To exit to interface of global fast Ethernet configuratio command n mode, Use this mode to Interface (with a switch enter exit. configure parameters configuration specific (config-if)# To exist to for the switch and interface) privileged Ethernet ports.
  • Page 34 system contact Set switch system switch(config)#system contact [System Contact] contact window string show system-info Show system switch>show system-info information ip address Configure the IP switch(config)#ip address [Ip-address] address of switch 192.168.16.1 255.255.255.0 [Subnet-mask] 192.168.16.254 [Gateway] ip dhcp Enable DHCP client switch(config)#ip dhcp function of switch Show IP information of...
  • Page 35 dhcpserver dnsip Configure DNS IP for switch(config)#dhcpserver dnsip [DNS IP] DHCP clients 192.168.1.1 dhcpserver leasetime Configure lease time switch(config)#dhcpserver [Hours] (in hour) leasetime 1 dhcpserver ipbinding Set static IP for DHCP switch(config)#interface [IP address] clients by port fastEthernet 2 switch(config)#dhcpserver ipbinding 192.168.1.1 show dhcpserver Show configuration of...

  • Page 36: Port Commands Set

    telnet server Port Commands Set Netstar Commands Level Description Example Choose the port for switch(config)#interface interface fastEthernet [Portid] modification. fastEthernet 2 duplex Use the duplex switch(config)#interface [full | half] configuration fastEthernet 2 command to specify switch(config-if)#duplex full the duplex mode of operation for Fast Ethernet.
  • Page 37 bandwidth type Set interface ingress switch(config)#interface broadcast-multicast-floo limit frame type to fastEthernet 2 ‘accept broadcast, switch(config-if)#bandwidth type ded-unicast multicast, and flooded broadcast-multicast-flooded-uni unicast frame’ cast bandwidth type Set interface ingress switch(config)#interface broadcast-multicast limit frame type to fastEthernet 2 ‘accept broadcast and switch(config-if)#bandwidth type multicast frame’...

  • Page 38: Trunk Commands Set

    state Use the state interface switch(config)#interface [Enable | Disable] configuration fastEthernet 2 command to specify (config-if)#state Disable the state mode of operation for Ethernet ports. Use the disable form of this command to disable the port. show interface show interface switch(config)#interface configuration configuration status...

  • Page 39: Vlan Commands Set

    workp [Port-list]:Member port switch(config)#aggregator group [Workport] list, This parameter 2 1,4,3 lacp workp 3 could be a port range(ex.1-4) or a port list separate by a comma(ex.2, 3, 6) [Workport]: The amount of work ports, this value could not be less than zero or be large than the amount of member ports.
  • Page 40 vlan database Enter VLAN configure switch#vlan database mode Vlanmode To set switch VLAN switch(vlan)#vlanmode portbase [portbase| 802.1q | mode. gvrp] switch(vlan)#vlanmode 802.1q switch(vlan)#vlanmode gvrp no vlan No VLAN Switch(vlan)#no vlan Ported based VLAN configuration vlan port-based Add new port based switch(vlan)#vlan port-based VALN grpname...

  • Page 41: Spanning Tree Commands Set

    [TaggedVID List] port belong to a trunk group, this command switch(vlan)#vlan 8021q port 3 can’t be applied. trunk-link tag 3-20 vlan 8021q port Assign a hybrid link for switch(vlan)#vlan 8021q port 3 [PortNumber] VLAN by port, if the hybrid-link untag 4 tag 3,6,8 hybrid-link untag [UntaggedVID] port belong to a trunk...
  • Page 42 [seconds] max-age global max-age 15 configuration command to change the interval between messages the spanning tree receives from the root switch. If a switch does not receive a bridge protocol data unit (BPDU) message from the root switch within this interval, it recomputed the Spanning Tree Protocol (STP)
  • Page 43 determines how long each of the listening learning states last before the port begins forwarding. stp-path-cost Use the spanning-tree switch(config)#interface [1~200000000] cost interface fastEthernet 2 configuration switch(config-if)#stp-path-cost 20 command to set the path cost for Spanning Tree Protocol (STP) calculations. In the event of a loop, spanning tree considers the path...

  • Page 44: Qos Commands Set

    stp-admin-edge Admin Edge of STP switch(config)#interface [True|False] priority on this fastEthernet 2 interface. switch(config-if)#stp-admin-edge True stp-admin-non-stp Admin NonSTP of STP switch(config)#interface [True|False] priority on this fastEthernet 2 interface. switch(config-if)#stp-admin-non-s tp False show spanning-tree Displays a summary of switch>show spanning-tree the spanning-tree states.

  • Page 45: Igmp Commands Set

    IGMP Commands Set Netstar Commands Level Description Example igmp enable Enable IGMP switch(config)#igmp enable snooping function Igmp-query auto Set IGMP query to switch(config)#Igmp-query auto auto mode Igmp-query force Set IGMP query to switch(config)#Igmp-query force force mode show igmp Displays the details of switch#show igmp configuration configuration an IGMP...

  • Page 46: Snmp Commands Set

    filter address table. filter no mac-address-table Remove an entry of switch(config)#interface static hwaddr MAC address table of fastEthernet 2 [MAC] interface (static) switch(config-if)#no mac-address-table static hwaddr 000012345678 no mac-address-table Remove an entry of switch(config)#no filter hwaddr MAC address table mac-address-table filter hwaddr [MAC] (filter) 000012348678...
  • Page 47 192.168.1.50 snmpv3 context-name Configure the context switch(config)#snmpv3 [Context Name ] name context-name Test snmpv3 user Configure the switch(config)#snmpv3 user [User Name] userprofile for test01 group G1 password group SNMPV3 agent. AuthPW PrivPW [Group Name] Privacy password password could be empty. [Authentication Password] [Privacy Password]...

  • Page 48: Port Mirroring Commands Set

    no snmp Remove the specified switch(config)#no snmp community-strings community. community-strings public [Community] no snmp-server host Remove the SNMP switch(config)#no snmp-server [Host-address] server host. 192.168.1.50 no snmpv3 user Remove specified user switch(config)#no snmpv3 user [User Name] of SNMPv3 agent. Test no snmpv3 access Remove specified switch(config)#no snmpv3 access context-name...

  • Page 49: 802.1X Commands Set

    monitor tx Set TX destination port switch(config)#monitor tx of monitor function show monitor Show port monitor switch#show monitor information monitor Configure source port switch(config)#interface [RX|TX|Both] of monitor function fastEthernet 2 switch(config-if)#monitor RX show monitor Show port monitor switch(config)#interface information fastEthernet 2 switch(config-if)#show monitor Disable source port of switch(config)#interface...
  • Page 50 command to change the accounting port 8021x system sharekey Use the 802.1x system switch(config)# 8021x system [ID] share key global sharekey 123456 configuration command to change the shared key value. 8021x system nasid Use the 802.1x system switch(config)# 8021x system [words] nasid global nasid test1...

  • Page 51: Tftp Commands Set

    8021x misc maxrequest Use the 802.1x misc switch(config)# 8021x misc [number] max request global maxrequest 3 configuration command to set the MAX requests. 8021x misc Use the 802.1x misc switch(config)# 8021x misc reauthperiod [sec.] reauth period global reauthperiod 3000 configuration command to set the reauth period.

  • Page 52: Systemlog, Smtp And Event Commands Set

    server and the file name of image. upgrade Upgrade firmware by switch(config)#upgrade flash:upgrade_fw TFTP and need to lash:upgrade_fw specify the IP of TFTP server and the file name of image. SystemLog, SMTP and Event Commands Set Netstar Commands Level Description Example systemlog ip Set System log server...
  • Page 53 no smtp Disable SMTP function switch(config)#no smtp event device-cold-start Set cold start event switch(config)#event [Systemlog|SMTP|Both] type device-cold-start both event Set Authentication switch(config)#event authentication-failure failure event type authentication-failure both [Systemlog|SMTP|Both] event Set X-ring topology switch(config)#event X-ring-topology-change changed event type X-ring-topology-change both [Systemlog|SMTP|Both] event systemlog Set port event for...

  • Page 54: Sntp Commands Set

    SNTP Commands Set Netstar Commands Level Description Example sntp enable Enable SNTP function switch(config)#sntp enable sntp daylight Enable daylight saving switch(config)#sntp daylight time, if SNTP function is inactive, this command can’t be applied. sntp daylight-period Set period of daylight switch(config)# sntp [Start time] [End time] saving time, if SNTP daylight-period 20060101-01:01...

  • Page 55: Pro-Ring Commands Set

    show sntp timezone Show index number of switch#show sntp timezone time zone list no sntp Disable SNTP function switch(config)#no sntp no sntp daylight Disable daylight saving switch(config)#no sntp daylight time Pro-Ring Commands Set Netstar Commands Level Description Example Xring enable Enable X-ring switch(config)#Xring enable Xring master...

  • Page 56: Web-Based Management

    Web-Based Management This section introduces the configuration and functions of the Web-Based management. About Web-based Management On CPU board of the switch there is an embedded HTML web site residing in flash memory, which offers advanced management features and allow users to manage the switch from anywhere on the network through a standard browser such as Microsoft Internet Explorer.

  • Page 57: System Login

    System Login Launch the Internet Explorer on the PC Key in ‘http:// ‘+’ the IP address of the switch’, and then Press ‘Enter’. The login screen will appear right after Key in the user name and password. The default user name and password are the same as ‘root’...

  • Page 58: Main Interface

    Main interface Main interface...

  • Page 59: System Information

    System Information Assigning the system name, location and view the system information System Name: Assign the name of switch. The maximum length is 64 bytes System Description: Displays the description of switch. Read only cannot be modified System Location: Assign the switch physical location. The maximum length is 64 bytes System Contact: Enter the name of contact person or organization Firmware Version: Displays the switch’s firmware version...

  • Page 60: Dhcp Server - System Configuration

    IP Address: Assign the IP address that the network is using. If DHCP client function is enabling, and then user don’t need to assign the IP address. And, the network DHCP server will assign the IP address for the industrial switch and displays in this column.

  • Page 61: Dhcp Client - System Configuration

    High IP Address: the dynamic IP assign range. High IP address is the end of the dynamic IP assigns range. For example: dynamic IP assign range is from 192.168.1.100 ~ 192.168.1.200. In comparison, 192.168.1.200 is the High IP address. Subnet Mask: the dynamic IP assign range subnet mask. Gateway: the gateway in your network.

  • Page 62: Dhcp Server - Port And Ip Bindings

    DHCP Server - Port and IP Bindings You can assign the specific IP address that is the IP in dynamic IP assign range to the specific port. When the device is connecting to the port and asks for dynamic IP assigning, the system will assign the IP address that has been assigned before to the connected device.

  • Page 63: Tftp - Restore Configuration

    Update Firmware interface TFTP – Restore Configuration You can restore EEPROM value from TFTP server, but you must put the image file on TFTP server first, switch will download back flash image. TFTP Server IP Address: fill in the TFTP server IP. Restore File Name: fill in the correct restore file name.

  • Page 64: System Event Log - Syslog Configuration

    Click Apply Backup Configuration interface System Event Log – Syslog Configuration Configuring the system event mode that want to be collected and system log server IP. Syslog Client Mode: select the system log mode – client only, server only, or both S/C.

  • Page 65: System Event Log - Smtp Configuration

    Syslog Configuration interface System Event Log - SMTP Configuration You can set up the mail server IP, mail account, account password, and forwarded email account for receiving the event alert. Email Alert: enable or disable the email alert function. SMTP Server IP: set up the mail server IP address (when Email Alert enabled, this function will then be available).
  • Page 66 where the event log comes from. Authentication: mark the check box to enable and configure the email account and password for authentication (when Email Alert enabled, this function will then be available). Mail Account: set up the email account, e.g. johnadmin, to receive the alert. It must be an existing email account on the mail server, which you had set up in SMTP Server IP Address column.

  • Page 67: System Event Log - Event Configuration

    System Event Log - Event Configuration You can select the system log events and SMTP events. When selected events occur, the system will send out the log information. Also, per port log and SMTP events can be selected. After configure, Click Apply System event selection: 4 selections –...
  • Page 68 Event Configuration interface Port event selection: select the per port events and per port SMTP events. It has 3 selections – Link UP, Link Down, and Link UP & Link Down. Disable means no event is selected. Link UP: the system will issue a log message when port connection is up only. Link Down: the system will issue a log message when port connection is down only.

  • Page 69: Fault Relay Alarm

    Fault Relay Alarm Power Failure: Mark the check box to enable the function of lighting up FAULT LED on the panel when power fails. Port Link Down/Broken: Mark the check box to enable the function of lighting up FAULT LED on the panel when Ports’ states are link down or broken. Fault Relay Alarm interface SNTP Configuration You can configure the SNTP (Simple Network Time Protocol) settings.
  • Page 70 Oscar Time Zone -2 hours 10 am ADT - Atlantic Daylight -3 hours 9 am AST - Atlantic Standard -4 hours 8 am EDT - Eastern Daylight EST - Eastern Standard -5 hours 7 am CDT - Central Daylight CST - Central Standard -6 hours 6 am MDT - Mountain Daylight...
  • Page 71 ZP5 - USSR Zone 4 +5 hours 5 pm ZP6 - USSR Zone 5 +6 hours 6 pm WAST - West Australian +7 hours 7 pm Standard CCT - China Coast, +8 hours 8 pm USSR Zone 7 JST - Japan Standard, +9 hours 9 pm USSR Zone 8...

  • Page 72: Ip Security

    SNTP Configuration interface IP Security IP security function allows user to assign 10 specific IP addresses that have permission to access the switch through the web browser for the securing switch management. IP Security Mode: when this option is in Enable mode, the Enable HTTP Server and Enable Telnet Server check boxes will then be available.

  • Page 73: User Authentication

    IP Security interface User Authentication Change web management login user name and password for the management security issue User name: Key in the new user name (The default is ‘root’) Password: Key in the new password (The default is ‘root’) Confirm password: Re-type the new password And then, click Apply...

  • Page 74: Port Statistics

    Port Statistics The following information provides the current port statistic information. Port: The port number. Type: Displays the current speed of connection to the port. Link: The status of linking—‘Up’ or ‘Down’. State: It’s set by Port Control. When the state is disabled, the port will not transmit or receive any packet.

  • Page 75: Port Control

    Port Control In Port control, you can view every port status that depended on user setting and the negotiation result. Port: select the port that you want to configure. State: Current port status. The port can be set to disable or enable mode. If the port setting is disable then will not receive or transmit any packet.

  • Page 76: Port Trunk

    Port Trunk The Link Aggregation Control Protocol (LACP) provides a standardized means for exchanging information between Partner Systems on a link to allow their Link Aggregation Control instances to reach agreement on the identity of the Link Aggregation Group to which the link belongs, move the link to that Link Aggregation Group, and enable its transmission and reception functions in an orderly manner.

  • Page 77: Aggregator Information

    button to delete Trunk Group. Select the Group ID and click Delete Delete button. Port Trunk—Aggregator Setting interface Aggregator Information When you have setup the aggregator setting with LACP disabled, you will see the local static trunk group information here.

  • Page 78: State Activity

    Port Trunk – Aggregator Information interface State Activity When you had setup the LACP aggregator, you can configure port state activity. You can mark or un-mark the port. When you mark the port and click button the port state Apply activity will change to Active.

  • Page 79: Port Mirroring

    Port Mirroring The Port mirroring is a method for monitor traffic in switched networks. Traffic through ports can be monitored by one specific port. That means traffic goes in or out monitored (source) ports will be duplicated into mirror (destination) port. Destination Port: There is only one port can be selected to be destination (mirror) port for monitoring both RX and TX traffic which come from source port.

  • Page 80: Vlan Configuration

    have 4 options for selecting: All, Broadcast/Multicast/Flooded Unicast, Broadcast/Multicast and Broadcast only. Broadcast/Multicast/Flooded Unicast, Broadcast/Multicast and Bbroadcast only types are only for ingress frames. The egress rate only supports All type. Rate Limiting interface All the ports support port ingress and egress rate control. For example, assume port 1 is 10Mbps, users can set it’s effective egress rate is 1Mbps, ingress rate is 500Kbps.

  • Page 81: Vlan Configuration - Port-Based Vlan

    receive traffic from the same members of VLAN. Basically, creating a VLAN from a switch is logically equivalent of reconnecting a group of network devices to another Layer 2 switch. However, all the network devices are still plugged into the same switch physically. The industrial switch supports port-based and 802.1Q (tagged-based) VLAN.
  • Page 82 VLAN – Port Based interface Click to add a new VLAN group(The maximum VLAN group is up to 64 VLAN groups) Entering the VLAN name, group ID and grouping the members of VLAN group And then, click Apply...
  • Page 83 VLAN—Port Based Add interface You will see the VLAN displays. Delete button to delete unwanted VLAN. button to modify existing VLAN group. Edit Note Remember to execute the ‘Save Configuration’ action, otherwise the new configuration will lose when switch power off.

  • Page 84: 802.1Q Vlan

    802.1Q VLAN Tagged-based VLAN is an IEEE 802.1Q specification standard. Therefore, it is possible to create a VLAN across devices from different switch venders. IEEE 802.1Q VLAN uses a technique to insert a ‘tag’ into the Ethernet frames. Tag contains a VLAN Identifier (VID) that indicates the VLAN numbers.
  • Page 85 802.1Q Configuration Enable GVRP Protocol: check the check box to enable GVRP protocol. Select the port that wants to configure. Link Type: there are 3 types of link type. Access Link: single switch only, allow user to group ports by setting the same VID.
  • Page 86 Group Configuration interface You can Change the VLAN group name and VLAN ID. Click Apply Group Configuration interface...

  • Page 87: Rapid Spanning Tree

    Rapid Spanning Tree The Rapid Spanning Tree Protocol (RSTP) is an evolution of the Spanning Tree Protocol and provides for faster spanning tree convergence after a topology change. The system also supports STP and the system will auto detect the connected device that is running STP or RSTP protocol.

  • Page 88: Rstp - Port Configuration

    RSTP System Configuration interface RSTP - Port Configuration You can configure path cost and priority of every port. 1. Select the port in Port column. 1. Path Cost: The cost of the path to the other bridge from this transmitting bridge at the specified port.

  • Page 89: Snmp Configuration

    enabling. False is P2P disabling. 4. Edge: The port directly connected to end stations cannot create bridging loop in the network. To configure the port as an edge port, set the port to ‘True’ status. 5. Non Stp: The port includes the STP mathematic calculation. True is not including STP mathematic calculation.

  • Page 90: System Configuration

    problems, and plan for network growth. Network management systems learn of problems by receiving traps or change notices from network devices implementing SNMP. System Configuration Community Strings You can define new community string set and remove unwanted community string. String: fill the name of string. RO: Read only.

  • Page 91: Trap Configuration

    SNMP System Configuration interface Trap Configuration A trap manager is a management station that receives traps, the system alerts generated by the switch. If no trap manager is defined, no traps will issue. Create a trap manager by entering the IP address of the station and a community string. To define management stations as trap manager and enter SNMP community strings and selects the SNMP version.

  • Page 92: Snmpv3 Configuration

    Trap Managers interface SNMPV3 Configuration Configure the SNMP V3 function. Context Table Configure SNMP v3 context table. Assign the context name of context table. Click to add context name. Click Remove to remove unwanted context name. User Profile Configure SNMP v3 user table.. User ID: set up the user name.
  • Page 93 SNMP V3 configuration interface Group Table Configure SNMP v3 group table.
  • Page 94 Security Name (User ID): Assign the user name that you have set up in user table. Group Name: Set up the group name. Click to add context name. Click Remove to remove unwanted context name. Access Table Configure SNMP v3 access table. Context Prefix: Set up the context name.

  • Page 95: Qos Configuration

    QoS Configuration You can configure Qos policy and priority setting, per port priority setting, COS and TOS setting. QoS Policy and Priority Type Qos Policy: select the QoS policy rule. Use an 8,4,2,1 weighted fair queuing scheme: The switch will follow 8:4:2:1 rate to process priority queue from High to lowest queue.

  • Page 96: Port Base Priority

    QoS Configuration interface Port Base Priority Configure per port priority level. Port: each port has 4 priority levels – High, Middle, Low, and Lowest. Click Apply...

  • Page 97: Cos Configuration

    COS Configuration Set up the COS priority level. COS priority: Set up the COS priority level 0~7 –High, Middle, Low, Lowest. Click Apply TOS Configuration Set up the TOS priority. TOS priority: the system provides 0~63 TOS priority level. Each level has 4 types of priority –...
  • Page 98 A message sent from the querier (IGMP router or switch) Query asking for a response from each host belonging to the multicast group. A message sent by a host to the querier to indicate that the host wants to be or is a member of a given group indicated in Report the report message.

  • Page 99: Pro-Ring System

    Pro-Ring System X-Ring provides a faster redundant recovery than Spanning Tree topology. The action is similar to STP or RSTP, but the algorithms not the same. In the X-Ring topology, every switch should enable X-Ring function and assign two member ports in the ring. Only one switch in the X-Ring group would be set as a master switch that would be blocked, called backup port, and another port is called working port.
  • Page 100 Coupling port: Assign the member port. Control port: Set the switch as the master switch in the coupling ring. Enable Dual Homing: Set up one of port on the switch to be the Dual Homing port. In an X-Ring group, maximum Dual Homing port is one. Dual Homing only work when the X-Ring function enable.

  • Page 101: Security

    Security In this section, you can configure 802.1x and MAC address table. 802.1X/Radius Configuration 802.1x is an IEEE authentication specification that allows a client to connect to a wireless access point or wired switch but prevents the client from gaining access to the Internet until it provides authority, like a user name and password that are verified by a separate server.
  • Page 102 802.1x System Configuration interface 802.1x Per Port Configuration You can configure 802.1x authentication state for each port. The State provides Disable, Accept, Reject and Authorize. Use ‘Space’ key change the state value. Reject: the specified port is required to be held in the unauthorized state. Accept: the specified port is required to be held in the Authorized state.
  • Page 103 802.1x Per Port Setting interface Misc Configuration Quiet Period: set the period during which the port doesn’t try to acquire a supplicant. TX Period: set the period the port wait for retransmit next EAPOL PDU during an authentication session. Supplicant Timeout: set the period of time the switch waits for a supplicant response to an EAP request.

  • Page 104: Mac Address Table

    802.1x Misc Configuration interface MAC Address Table Use the MAC address table to ensure the port security. Static MAC Address You can add a static MAC address; it remains in the switch's address table, regardless of whether the device is physically connected to the switch. This saves the switch from having to re-learn a device's MAC address when the disconnected or powered-off device is active on the network again.
  • Page 105 Static MAC Addresses interface MAC Filtering By filtering MAC address, the switch can easily filter pre-configure MAC address and reduce the un-safety. You can add and delete filtering MAC address. MAC Filtering interface...
  • Page 106 MAC Address: Enter the MAC address that you want to filter. Click If you want to delete the MAC address from filtering table, select the MAC address and click Delete All MAC Addresses You can view the port that connected device’s MAC address and related devices’ MAC address.

  • Page 107: Factory Default

    Factory Default Reset switch to default configuration. Click Reset to reset all configurations to the default value. Factory Default interface Save Configuration Save all configurations that you have made in the system. To ensure the all configuration will be saved. Click to save the all configuration to the flash memory.

  • Page 108: Troubles Shooting

    Troubles shooting Verify that you are using the right power cord/adapter (DC 9 ~ 56V), please don’t use the power adapter with DC output higher than 56V, or it will burn this switch down. Select the proper UTP cable to construct your network. Please check that you are using the right cable.

  • Page 109: Technical Specification

    Technical Specification The technical specifications of 4 10/100/1000T + 4 SFP Industrial Switch are listed as follows. Communications Compatibility IEEE 802.3, 802.3u, 802.3ab IEEE 802.3x, 802.3z, 802.3ad IEEE 802.1d, 802.1p, 802.1Q, 802.1x IEEE 802.1ab 10/100/1000Base-T, 1000Base-FX Transmission Speed Up to 1000 Mbps Interface 4 x RJ-45 (4-port 10/100/1000TX) Connectors...
  • Page 110 802.1w/D RSTP/STP IP Access security, post security, DHCP Server, Security Port and IP Binding, 802.1X Port Access Control Traffic Control IGMP Snooping/Query for multicast group management Port Trunking, Static/802.3ad LACP Rate limit and storm control IEEE 802.1p QoS Cos/TOS/DSCP priority queuing IEEE 802.3x flow control Diagnostics Port Mirroring, Real-time traffic statistic, MAC...
  • Page 111 Environment -40 ~ 85 ℃ Operating Temperature Operating Humidity 5% ~ 95% (non-condensing) -40 ~ 85 ℃ Storage Temperature Certifications UL, cUL, CE EN60950-1 Safety FCC Class A, CE EN61000-4-2 (ESD) CE EN61000-4-3 (RS) CE EN61000-4-4 (EFT) CE EN61000-4-5 (Surge) CE EN61000-4-6 (CS) CE EN61000-4-8 CE EN61000-4-11...

Table of Contents