Stick Alarm - FUTABA T14SG Software Update Manual

*S3171SB・S9071SB・S9072SB・S9074SB・S9075SB can not be set to OLP.
These servos apply to NORMAL mode and RETRACTABLE mode only.
8.MODEL TYPE (Addition of MULTIROTOR)
MUTIROTOR type is added to
MODEL TYPE.
■ W h e n a m o d e l t y p e i s
M U L T I R O T O R , a n i c o n f o r
exclusive use is displayed on
HOME screen.
■ When a model type is MULTIROTOR, the LINKAGE menu is below.
(It is FASSTest 14CH mode. It differs at other mode.) Please refer
FUNCTION OF LINKAGE MENU in the instruction manual of T14SG/
FX-22 for each function.
*STK ALARM is an addtional function for all model types.
■ When a model type is MULTIROTOR, the MODEL menu is below.
Please refer FUNCTION OF MODEL MENU in the instruction manual
of T14SG/FX-22 for each function.
■ The default setting of CH and functions are below;
■ The functions which can be set are below.
FUNCTION
Normal Short
AILERON AIL
ELEVATOR ELE
THROTTLE THR
RUDDER RUD
GYRO GYR
GYRO2 GYR2
GYRO3 GYR3
CAM TILT TILT
CAMERA PAN PAN
CAMERA REC REC
MODE MODE
AUXILIARY6 AUX6
AUXILIARY5 AUX5
AUXILIARY4 AUX4
AUXILIARY3 AUX3
AUXILIARY2 AUX2
AUXILIARY1 AUX1
*CAM TILT, CAMERA PAN, CAMERA REC and MODE which are added for MULTIROTOR
do not have any special functions. They are same as AUXILIARY functons.
*GYRO menu is same as GYRO for the
airplane.
*THR CURVE menu is same as THR
CURVE for the airplane.
■ The default settings of TRAINER at MULTIROTOR are below. It is easy
to set TRAINER, when the student radio is used for camera gimbal
control.
*Please do not use REVERSE, END POINT and any other Mixers at student
transmitter.
9.GYRO (Corresponding model type : AIRPLANE / GLIDER
and MULTIROTOR)
The fine tuning hardware setting is added to GYRO for AIRPLANE and
GLIDER.
Setting range ：
GY type : Setting rate ± 20% (The actual rate has not to be greater than 100%.)
NORM type : Setting rate ± 10.0% (The actual rate has not to be greater than 100%.)
10.STICK ALARM (Corresponding model type : All Model
Types)
An alarm (single beep) can be sounded at the specified stick position.
■ Alarm function ON/OFF can be set by switch.
The stick position for an
alarm
11.TIMER (ST1 and ST2 speech function)
Speech function is added to TIMER (ST1 and ST2).
When mode is UP timer or DOWN timer, the speech outputs is avalable.
It is phone output only.
■↑ mode
The voice outputs each minute of the time elapsed from timer start.
Ex. one minute, ・・・ two minutes, ・・・
It outputs voice 20 seconds before reaching to the target time.
Ex. twenty seconds
It is counted down by voice from 10 seconds before reaching to the
target time.
Ex. ten, nine, eight ・・・ three, two, one
■↓ mode
The voice outputs each minute of the time remaining up to the alarm time.
Ex. ・・・ ten minutes, ・・・ nine minutes, ・・・
It outputs voice every 10 seconds from 50 seconds before reaching to
the target time.
Ex. fifty seconds, ・・・ forty seconds, ・・・
It is counted down by voice from 10 seconds before reaching to the
target time.
Ex. ten, nine, eight ・・・ three, two, one
*The voice alarm of timer is delayed from the actual time.
*During logging telemetry data, the voice alarm is delayed more.
*The priority of the timer speech is higher than the telemetry speech. Then,
- 6 -
This is an actual rate.
It is not greater than 100%.
The hardware is selectable.
ON/OFF switch is selectable.
Stick is selectable. (J1, J2, J3, J4)
The default setting :
Mode 1 → J2 Mode 2 → J3
100%
Current stick position
J1 J4 0%
0%
J2 J3
100%