Related Manuals for SEW-Eurodrive Didactics
Summary of Contents for SEW-Eurodrive Didactics
- Page 1 *28521072_1218* Drive Technology \ Drive Automation \ System Integration \ Services Operating Instructions Didactics – Electromechanics Motor Load Diagnostics Module Edition 12/2018 28521072/EN...
- Page 2 SEW-EURODRIVE—Driving the world...
-
Page 3: Table Of Contents
Device components ...................... 12 Installation.......................... 13 Important information .................... 13 Electrical connections .................... 14 Wiring diagram...................... 18 Startup ............................. 19 Important information .................... 19 Starting up the didactics module................... 20 Operation.......................... 21 Important information .................... 21 Evaluating diagnostic data .................... 21 Service ............................. 22 Electronics Service by SEW‑EURODRIVE.............. 22 Waste disposal...................... 22 Technical data......................... -
Page 4: General Information
General information About this documentation General information About this documentation The current version of the documentation is the original. This documentation is an integral part of the product. The documentation is intended for all employees who perform work on the product. Make sure this documentation is accessible and legible. -
Page 5: Decimal Separator In Numerical Values
General information Decimal separator in numerical values Hazard symbol Meaning Warning of dangerous electrical voltage Warning of hot surfaces Warning of automatic restart 1.2.3 Structure of embedded safety notes Embedded safety notes are directly integrated into the instructions just before the de- scription of the dangerous action. -
Page 6: Product Names And Trademarks
General information Product names and trademarks SEW‑EURODRIVE website (www.sew‑eurodrive.com) provides a wide selection of documents for download in various languages. If required, you can also order prin- ted and bound copies of the documentation from SEW‑EURODRIVE. Product names and trademarks The brands and product names in this documentation are trademarks or registered trademarks of their respective titleholders. -
Page 7: Safety Notes
Safety notes Preliminary information Safety notes Preliminary information The following general safety notes serve the purpose of preventing injury to persons and damage to property. They primarily apply to the use of products described in this documentation. If you use additional components, also observe the relevant warning and safety notes. -
Page 8: Transport
Safety notes Transport The motors must be suitable for operation with drive inverters. Do not connect any other loads to the product. Startup (i.e. start of regular operation) is permitted with adherence to EMC guideline only. Technical data and information on the connection conditions are provided on the nameplate and in the documentation. -
Page 9: Startup And Operation
Safety notes Startup and operation The preventive measures and protection devices must comply with the applicable reg- ulations (e.g. EN 60204-1 or EN 61800-5-1). Ground connections are required as preventive measures. Startup and operation Before startup, make sure that the 4 mm sockets, buttons, and switches are intact. It might be necessary to equip locations where such devices are used with additional monitoring and protection devices in accordance with the respective applicable safety regulations, e.g. -
Page 10: Device Structure
Device structure Scope of delivery Device structure Scope of delivery The following components are included in the scope of delivery: • Affixed front panel • Housing • Assembled and checked printed circuit board for the power section Short designation The following short designations are used in this documentation: Device Designation Phoenix Contact ELR H5-IES-... -
Page 11: Basic Device
Power section connection EMM [11] Motor connection Electronic motor management (EMM) [12] Motor connection ELR Switch for input simulation [13] PE: PE connection Power section connection as bridge connection for another didactics module Operating Instructions – Motor Load Diagnostics Module... -
Page 12: Device Components
SEW-EURODRIVE recommends the following motor type for training on an asynchro- nous motor with simple encoder technology: • DR.. series AC motor Recommendation: Didactics motor assembly DRS71S4 3.4.2 Hybrid motor starter It is possible to implement the following functions, among others, with the hybrid motor starter with reversing function: •... -
Page 13: Installation
• 4 mm laboratory safety plug connectors with rigid insulating sleeve, suited for nom- inal voltages of up to 1000 V. • Didactics connection cable from SEW‑EURODRIVE. The cable must not be longer than 3 m. Operating Instructions – Motor Load Diagnostics Module... -
Page 14: Electrical Connections
N: Line connection of neutral conductor PE: PE connection 4.2.2 X2: Motor connection NOTICE Damage to the didactics module due to overload. Damage to property. • Only connect one motor to the didactics module. Operating Instructions – Motor Load Diagnostics Module... - Page 15 Installation Electrical connections 9250653707 PE: PE connection Motor phases U, V, W ® Motor connection HARTING connector type Han Q5 EMC female Article no.: Connector: 09620030301, insert: 09120053101 To connect the motor, use either the connections for the U, V, and W motor phases or the connector.
- Page 16 Installation Electrical connections 4.2.4 Connections of the electronic motor management 1/L1 2/L2 3/L3 IN 1 IN 2 IN 3 IN 4 4/T1 5/T2 6/T3 24 V 9293763723 Power section connection Electronic motor management Connections of the electronic motor management: • O 1 – O 4: digital outputs •...
- Page 17 Installation Electrical connections 4.2.5 Connection of power jumper to another didactics module 230 V 24 V 24 V 9250656395 L: Line connection phase N: Line connection of neutral conductor PE: PE connection 24 V control voltage Operating Instructions – Motor Load Diagnostics Module...
-
Page 18: Wiring Diagram
Installation Wiring diagram Wiring diagram 9007208500415371 Operating Instructions – Motor Load Diagnostics Module... - Page 19 Startup Important information Startup Important information INFORMATION • Before startup, make sure that the product is not damaged. • Check that all protective covers are installed correctly. • Observe the documentation of components connected or mounted to the module (e.g. motor, inverter). WARNING Danger of electric shock due to open connections.
-
Page 20: Startup
7. Connect the connections to the didactics module. Do not connect the connections during ongoing operation. 8. In the case of external control, set all toggle switches of the didactics module to "0" (zero) position for input simulation. 9. Apply the line voltage. -
Page 21: Operation
Operation Important information Operation Important information INFORMATION • Check that all protective covers are installed correctly. • Observe the documentation of components connected or mounted to the module (e.g. motor, inverter). WARNING Electric shock when disconnecting or connecting voltage-carrying plug connectors. Severe or fatal injuries. -
Page 22: Service
Service Electronics Service by SEW‑EURODRIVE Service Electronics Service by SEW‑EURODRIVE If you are unable to rectify a fault, contact SEW‑EURODRIVE Service. For the ad- dresses, refer to www.sew‑eurodrive.com. When contacting the SEW‑EURODRIVE service, always specify the following informa- tion so that our service personnel can assist you more effectively: •... -
Page 23: Technical Data
Dimensions W × H × D 315 mm × 67 mm (front) / 115 mm (rear) × 297 mm The technical data of the didactics module are decisively influenced by the electronic motor management and the hybrid motor starter. For further information, refer to the documentation of the manufacturer, Phoenix Con- tact (see the chapter "Applicable documentation" (→ 2 5)). -
Page 24: Standards And Certifications
Standards and certifications EC declaration of conformity Standards and certifications The SEW‑EURODRIVE components were developed and tested based on the latest, national standards and certifications. If special approvals are necessary for additional requirements, request them separ- ately from SEW‑EURODRIVE. EC declaration of conformity The EC declarations of conformity for the SEW components are listed on the website of SEW‑EURODRIVE with the respective products. -
Page 25: Address List
Address list Address list Germany Headquarters Bruchsal SEW-EURODRIVE GmbH & Co KG Tel. +49 7251 75-0 Production Ernst-Blickle-Straße 42 Fax +49 7251 75-1970 Sales 76646 Bruchsal http://www.sew-eurodrive.de sew@sew-eurodrive.de Production / Industrial Bruchsal SEW-EURODRIVE GmbH & Co KG Tel. +49 7251 75-0 Gears Christian-Pähr-Str. -
Page 26: Index
Rights to claim under limited warranty .... 5 Declaration of conformity........ 24 Designated use ............. 7 Device structure .......... 10 Safety notes Didactics module structure ........ 11 Assembly............ 8 Documentation, applicable ........ 5 Designation in the documentation .... 4 Installation ............ 13 Meaning of the hazard symbols ....... - Page 27 Index Waste disposal ............ 22 Wiring diagram ............ 18 Operating Instructions – Motor Load Diagnostics Module...
- Page 32 SEW-EURODRIVE—Driving the world SEW-EURODRIVE GmbH & Co KG Ernst-Blickle-Str. 42 76646 BRUCHSAL GERMANY Tel. +49 7251 75-0 Fax +49 7251 75-1970 sew@sew-eurodrive.com www.sew-eurodrive.com...
Need help?
Do you have a question about the Didactics and is the answer not in the manual?
Questions and answers