® With MOVIDRIVE B drive inverter module .............. 19 Startup with other modules ................... 20 Checking the connection of the brake................ 20 Operating principle of BMV brake control .............. 20 Operation.......................... 21 Important information .................... 21 Operating and controlling the brake................ 21 Service ............................. 23 Electronics Service by SEW‑EURODRIVE.............. 23 Waste disposal...................... 23...
Page 4
Table of contents Certifications ......................... 25 Address list .......................... 26 Index ............................ 27 Operating Instructions – Brake Control Module (BMV)
Type and source of hazard. Possible consequence(s) if disregarded. • Measure(s) to prevent the hazard. Meaning of the hazard symbols The hazard symbols in the safety notes have the following meaning: Hazard symbol Meaning General hazard Operating Instructions – Brake Control Module (BMV)
The product is not intended for use in ap- plications (such as lifting applications). The product can be used to operate AC asynchronous motors and synchronous ser- vomotors with squirrel-cage rotor. Operating Instructions – Brake Control Module (BMV)
Ensure that all of the required covers are correctly attached after the electrical installa- tion. The preventive measures and protection devices must comply with the applicable reg- ulations (e.g. EN 60204-1 or EN 61800-5-1). Operating Instructions – Brake Control Module (BMV)
Ensure a de-energized state of the product be- fore you start working on it. Ensure a de-energized state for the entire time you work on the product. Repair work may only be carried out by SEW‑EURODRIVE. Operating Instructions – Brake Control Module (BMV)
Applied Inverter Released Brake connection 9007217489840139 [1] Brake control unit BMV 5 [4] Selector switches [2] Brake connection [5] Control voltage/control signal U DC 24 V [3] PE: PE connection [6] Voltage supply DC 24 V (brake voltage) Operating Instructions – Brake Control Module (BMV)
• 4 mm laboratory safety plug connectors with rigid insulating sleeve, suited for nom- inal voltages of up to 1000 V. • Didactics connection cable from SEW‑EURODRIVE. The cable must not be longer than 3 m. Operating Instructions – Brake Control Module (BMV)
You can connect the motor brake to the brake control unit using 4 mm safety tower plugs 1000 V CAT II. However, SEW‑EURODRIVE recommends to use shielded brake cables. Electrical connections 4.2.1 Brake voltage supply +24V DC 0V DC 18235822603 DC +24 V DC 0 V (GND) Operating Instructions – Brake Control Module (BMV)
Page 13
+24V DC +24V DC 0V DC 18379814027 Input for control voltage of the inverter Input for the control voltage/control signal U (external) Ground (GND) 4.2.3 PE connection 18235773707 4.2.4 Brake connection Brake connection 18235831051 Operating Instructions – Brake Control Module (BMV)
Protect the brake against overvoltage in the following cases, for example by means of varistor overvoltage protection: • When operated on third-party inverters • When using brakes that are not directly supplied from SEW‑EURODRIVE invert- ers. Operating Instructions – Brake Control Module (BMV)
Page 15
The following figure shows the terminals on the cable end and on the motor end: – BK – BK + GNYE GNYE 18100985355 Connection on cable end Brake coil Connection on motor end Motor cable labeling BP brake Operating Instructions – Brake Control Module (BMV)
Page 16
The following figure shows the terminals on the cable end and on the motor end: GNYE GNYE 18385019915 Connection on cable end Brake coil Connection on motor end Motor cable labeling BY brake Designation on BMV brake control Operating Instructions – Brake Control Module (BMV)
BE brake: DC 24 V DC 24 V 18101028747 Wiring diagram DC +24 V DC 0 V DC +24 V U in DC 24 V U in DC 0 V Housing Brake connection 9007217702210187 Operating Instructions – Brake Control Module (BMV)
Startup With MOVITRAC® B frequency inverter module Startup With MOVITRAC ® B frequency inverter module ® With MOVITRAC B frequency inverter module Wire the didactics modules as shown in the following figure: 9007217637527179 Operating Instructions – Brake Control Module (BMV)
Startup With MOVIDRIVE® B drive inverter module With MOVIDRIVE ® B drive inverter module ® With MOVIDRIVE B drive inverter module Wire the didactics modules as shown in the following figure: 9007217639313163 Operating Instructions – Brake Control Module (BMV)
Use shielded brake cables. Operating principle of BMV brake control BMV brake control energizes the brake coil if both power supply (according to the brake voltage 12 to 24 V) and a DC 24 V signal (e.g. from a frequency inverter or PLC) are present at the same time.
Using the selector switch, the brake of the connected motor can be operated as fol- lows: Inverter When the selector switch is set to "Inverter", the brake control receives a signal from the inverter to release the brake. The inverter controls release and application of the brake. Operating Instructions – Brake Control Module (BMV)
Page 22
When the selector switch is set to "Released", the brake is released permanently. (Re- quirement: Brake control is externally connected to 24 V and is wired accordingly, see wiring in the chapter "Startup".) In this case, brake control ignores the control signal from the inverter. Operating Instructions – Brake Control Module (BMV)
Page 23
Oil and grease Collect used oil and grease separately according to type. Ensure that the used oil is not mixed with solvent. Dispose of used oil and grease correctly. • Screens • Capacitors Operating Instructions – Brake Control Module (BMV)
Degree of protection IP20 Connection voltage 0 – 24 V (depending on the operating voltage of the brake) Control voltage DC 24 V Holding current 5 A Weight 1.2 kg Dimensions W × H × D 140 mm × 295 mm × 145 mm Operating Instructions – Brake Control Module (BMV)
The EC declarations of conformity for the SEW components are listed on the website of SEW‑EURODRIVE with the respective products. Certifications The certificates for the SEW components are listed on the website of SEW‑EURODRIVE with the respective products. Operating Instructions – Brake Control Module (BMV)
Page 26
Würzburg SEW-EURODRIVE GmbH & Co KG Tel. +49 931 27886-60 Nürnbergerstraße 118 Fax +49 931 27886-66 97076 Würzburg-Lengfeld dc-wuerzburg@sew-eurodrive.de Drive Service Hotline / 24 Hour Service 0 800 SEWHELP 0 800 7394357 Operating Instructions – Brake Control Module (BMV)
Page 27
Signal words in safety notes........ 5 PE.............. 13 Standards ............ 25 Voltage supply.......... 12 Startup .............. 18 Electronics Service .......... 23 Safety notes ............. 9 Embedded safety notes......... 6 Structure of the didactics module ...... 10 Operating Instructions – Brake Control Module (BMV)
Page 28
Index Target group ............ 7 Use ................ 7 Technical data ............. 24 Trademarks ............ 6 Waste disposal ............ 23 Transport ............... 8 Wiring diagram ............ 17 Operating Instructions – Brake Control Module (BMV)
Page 32
SEW-EURODRIVE—Driving the world SEW-EURODRIVE GmbH & Co KG Ernst-Blickle-Str. 42 76646 BRUCHSAL GERMANY Tel. +49 7251 75-0 Fax +49 7251 75-1970 sew@sew-eurodrive.com www.sew-eurodrive.com...
Need help?
Do you have a question about the BMV and is the answer not in the manual?
Questions and answers