Huawei SmartLogger1000 User Manual
Hide thumbs Also See for SmartLogger1000:
Table of Contents

Advertisement

Quick Links

SmartLogger1000
User Manual
Issue
12
Date
2019-01-15
HUAWEI TECHNOLOGIES CO., LTD.

Advertisement

Table of Contents
loading

Summary of Contents for Huawei SmartLogger1000

  • Page 1 SmartLogger1000 User Manual Issue Date 2019-01-15 HUAWEI TECHNOLOGIES CO., LTD.
  • Page 2 Notice The purchased products, services and features are stipulated by the contract made between Huawei and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS"...
  • Page 3: About This Document

    About This Document About This Document Purpose This document introduces the SmartLogger1000 (SmartLogger for short) in terms of installation, cable connections, system operation and maintenance, and troubleshooting. Readers should understand the SmartLogger features, functions, and safety precautions provided in this document before installing and operating the SmartLogger.
  • Page 4 Updated 7.10.3.2 Setting Email Parameters. Updated 7.10.4.1 Setting DO Parameters. Updated 7.11.1 Upgrading Firmware. Updated 7.11.4 System Maintenance. Updated 7.11.8.1 Connecting Devices. Updated 7.11.8.5 Data Recollection. Added 8.3.11 PF-U Characteristic Curve. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 5 6.2.4 Sending a Reset Command to the Inverter. Added 6.2.36 Resetting the System. Added 7.8.2.4 Setting a Tracking System. Added 7.8.2.5 Setting the LVRT Characteristic Curve. Issue 08 (2015-08-20) Added 6.2.31 Exporting All Files. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 6 Updated part of the web user interface (WebUI). Issue 03 (2013-09-10) This is the third official release. Compared with the second official release, this document updated some operations and figures for the LCD and WebUI. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 7 This is the second official release. Issue 01 (2013-04-25) This is the first official release. Compared with the original draft, this document updated some operations and figures for the LCD and WebUI. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 8: Table Of Contents

    4.5 Connecting to an EMI ..............................41 4.5.1 Connection Description ............................41 4.5.2 Connecting the SmartLogger to an EMI That Supports Standard Modbus-RTU ............. 41 4.5.3 Connecting the SmartLogger to a Split EMI ......................43 Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 9 6.2.27 Restoring Factory Settings ........................... 123 6.2.28 Downloading Device Data Using a USB Flash Drive ..................125 6.2.29 Upgrading Firmware by Using a USB Flash Drive ..................... 127 6.2.30 Batch Upgrade ..............................130 Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd. viii...
  • Page 10 7.8.4.1 Querying Related Information ..........................202 7.8.4.2 Setting EMI Parameters ............................202 7.8.5 Power Meter................................205 7.8.5.1 Querying Related Information ..........................205 7.8.5.2 Setting Running Parameters ..........................205 7.8.6 PID ..................................206 Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 11 7.10.6 Dry contact remote shutdown ..........................236 7.10.7 Setting DI Parameters ............................239 7.10.8 Setting Export Limitation Parameters ........................240 7.11 Maintenance ................................243 7.11.1 Upgrading Firmware ............................243 7.11.2 Product Information ............................. 244 Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 12 10 FAQ ............................276 10.1 How Do I Set Anti-crosstalk Parameters?....................... 276 10.2 Which Models of Power Meters and EMIs Are Supported by the SmartLogger? ..........278 11 Disposing of the SmartLogger ....................281 Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 13 SmartLogger1000 User Manual Contents 12 Technical Specifications ......................282 A Monitoring User List ....................... 284 B Acronyms and Abbreviations ....................285 Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 14: Safety Precautions

    Operation personnel should understand the composition and working principles of the PV grid-tied power generating system and local regulations. Read this document thoroughly before operations. Huawei shall not be liable for any consequence caused by violation of the storage, transportation, installation, and operation regulations specified in this document.
  • Page 15: Symbols

    EU waste electrical and Do not dispose of the electronic equipment SmartLogger as household (WEEE) label garbage. For details about how to deal with the undesirable SmartLogger, refer to 11 Disposing of the SmartLogger. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 16: Overview

    Modbus protocol or provide RS485 ports.  It can simultaneously connect to the Huawei and third-party network management systems by using the Modbus-TCP and IEC104 protocols.  It can connect to a multi-functional power meter over DLT645.
  • Page 17 Allows users to upgrade the firmware of the SmartLogger and inverters and export data by using a USB flash drive. − Allows users to upgrade the firmware of the SmartLogger or inverters and export logs over the embedded WebUI.  Grid dispatching Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 18: Appearance

     Remote maintenance − Supports connection to both Huawei NMS and a third-party NMS using Modbus-TCP and IEC104 protocol to remotely manage all devices. − Allows users to access a third-party NMS over the File Transfer Protocol (FTP).
  • Page 19 Figure 2-3 Side view of the SmartLogger 1. SD card slot (reserved) 2. USB port Rear View of the Shell Figure 2-4 Rear view of the SmartLogger 1. Mounting hole 2. Rail snap 3. Heat dissipation hole Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 20 Connects to a pulse output Reserved power meter CAN port CAN port Reserved COM1-COM3 RS485 Supports three RS485 ports that can connect to devices such as the inverter and environmental monitoring instrument (EMI). Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 21: Monitoring Panel

    Steady green The power supply is normal. There is no power supply. Run indicator Blinking green (on for 1s The SmartLogger is working. and then off for 1s) The SmartLogger stops working. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 22 Allows you to view the date and time. time 2. Energy Allows you to view the total energy production in each hour by all the production inverters connected to the SmartLogger. histogram Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 23: Typical Cable Connection Scenarios

    Recommended cable: three-core multi-wire (L1, L2, and L3) cable with the operating voltage to the ground not less than 600 V and the cross sectional area of a single core wire being 4 mm Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 24 To be supplied by 2 PCS an optical module of a the customer local model CT-GZF2PJ-8, To be supplied by 1 PCS CT-GPH-A-8, or an ATB the customer of a local model Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 25 Figure 2-9 Cable connections in the LTE+RS485/PLC scenario Table 2-5 lists the components required in this scenario. Table 2-5 Required components Component Model or Specifications Component Quantity Source SmartLogger SmartLogger1000 Can be 1 PCS purchased from Huawei Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 26 To be supplied 1 PCS rated current: ≥ 6 A; switch box by the number of phases: three customer Socket Matching with the power To be supplied 1 PCS adapter by the customer Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 27: Installation

    Do not store the SmartLogger in areas with flammable or explosive materials.  Do not install the SmartLogger on flammable building materials. 3.1 Installation Process This topic describes the SmartLogger installation process. The SmartLogger installation process is shown in Figure 3-1. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 28 Before installing the SmartLogger, determine an position. appropriate position to ensure that the SmartLogger works properly. Installing the SmartLogger The SmartLogger can be installed on a desk, a wall or along a guide rail. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 29: Checking Before Installation

    Hammer drill Drills holes in the wall when the SmartLogger is wall-mounted. Diagonal pliers Cuts and tighten cable ties. Wire stripper Peels cable jackets. Hammers expansion bolts into Rubber mallet holes. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 30 Vacuum cleaner Cleans up dust after holes are drilled. Diameter: ≤ 10 mm Marker Marks signs. Measuring tape Measures distance Ensures that the screws are Plumb line perpendicular to the wall. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 31: Determining The Installation Position

     The SmartLogger is at least 100 mm away from the neighboring objects on both sides, the top side, and the bottom side respectively, as shown in Figure 3-2. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 32: Installing The Smartlogger

    Step 1 Take the SmartLogger out from the package. Step 2 Place the SmartLogger onto a horizontal desk. ----End 3.5.2 Mounting the SmartLogger on a Wall This topic describes how to mount the SmartLogger on a wall. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 33 Use a marker to mark out the holes, as shown in Figure 3-3. Figure 3-3 Hole positions and dimensions Drill holes using a hammer drill and install expansion tubes and screws, as shown in Figure 3-4. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 34: Mounting The Smartlogger Along A Guide Rail

    This topic describes how to mount the SmartLogger along a guide rail. Context The guide rails are not delivered together with the SmartLogger. If you need to mount the SmartLogger along a guide rail, prepare a 35 mm wide guide rail. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 35 Step 2 Hold the two lower corners of the SmartLogger, pull it downwards appropriately, and then push it towards the guide rail. When you hear a click sound, the SmartLogger is successfully mounted along the guide rail, as shown in Figure 3-6. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 36: Installing The Rs485 Signal Spd

    SmartLogger. In this case, the recommended guide rail length is 400 mm or greater. Procedure Step 1 Secure the RS485 signal SPD to the guide rail, as shown in Figure 3-7. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 37 SmartLogger1000 User Manual 3 Installation Figure 3-7 Securing the RS485 signal SPD to the guide rail ----End Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 38: Electrical Connections

    Device Connection Description Figure 4-1 shows the recommended method for connecting the SmartLogger to multiple devices through the COM ports. For details, see 4.3 Connecting the RS485 Signal SPD–4.9 Connecting to a PID. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 39: Connecting The Pe Cable For The Rs485 Signal Spd

    Step 2 Insert the bare cable cores into port 3 of the RS485 signal SPD, as shown by (1) in Figure 4-2. Figure 4-2 Connecting the PE cable for the RS485 signal SPD Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 40: Connecting The Rs485 Signal Spd

    SPD. One RS485 signal SPD provides two RS485 surge protection ports, as shown in Figure 4-3. Figure 4-3 Ports on an RS485 signal SPD Table 4-1 describes the surge protection ports. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 41 Figure 4-4. Figure 4-4 Stripping an RS485 communications cable (unit: mm) Step 2 Remove the terminal block from the SmartLogger COM port, as shown in Figure 4-5. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 42 Step 4 Insert the terminal block into the SmartLogger COM port. Step 5 Insert the bare cable cores at the other end of the cable into a protection port of the RS485 signal SPD, as shown by (1) in Figure 4-7. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 43: Connecting The Smartlogger To Inverters

    This topic describes how to connect the SmartLogger to the SUN2000 using an RS485 communications cable. Context The SmartLogger provides three COM ports for RS485 communication, as shown in Figure 4-8. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 44 SUN2000s. All the SUN2000s have RJ45 ports. You are advised to use terminal blocks for connection.  Terminal block connection − Terminal block 1 Figure 4-9 shows the position of the terminal block in the SUN2000-50KTL/50KTL-C1. Table 4-3 describes the functions of the terminal block. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 45 RS485B, for RS485 negative differential RS485B OUT signaling − Terminal block 2 Figure 4-10 shows the position of the terminal block in the SUN2000-33KTL/40KTL. Figure 4-11 describes the functions of the terminal block. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 46 RS485B IN signaling RS485B OUT RS485B, for RS485 negative differential signaling  RJ45 network port connection The RJ45 port needs to be connected using an RJ45 connector, as shown in Figure 4-12. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 47 Figure 4-13 shows how to connect the SmartLogger to the SUN2000 through an RS485 signal SPD. This section describes how to connect the SUN2000-33KTL/40KTL to the SmartLogger through a terminal block. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 48 Figure 4-14 Stripping an RS485 communications cable (unit: mm) Step 3 Insert the bare core wires into the surge port of the RS485 signal SPD, as shown by (1) in Figure 4-15. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 49: Connecting The Sun2000L To The Smartlogger

    Take operations in reversed order to disconnect the SmartLogger from the SUN2000. 4.4.2 Connecting the SUN2000L to the SmartLogger Context The SmartLogger provides three COM ports for RS485 communication, as shown in Figure 4-16. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 50 COM2 port RS485A, for RS485 positive differential signaling RS485B, for RS485 negative differential signaling COM3 port RS485A, for RS485 positive differential signaling SUN2000L-4.125KTL-JP/4.95KTL-JP connects to the SmartLogger through the bottom COM port. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 51 485B2 RS485B, RS485 differential signal– 485A2 RS485A, RS485 differential signal+ Port for grounding the shield layer Figure 4-18 shows how the SmartLogger connects to the SUN2000L through an RS485 signal SPD. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 52 Figure 4-19 Stripping an RS485 communications cable (unit: mm) Step 3 Insert the bare core wires into the surge port of the RS485 signal SPD, as shown by (1) in Figure 4-20. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 53: Connecting Multiple Inverters To The Smartlogger

    4.4.3 Connecting Multiple Inverters to the SmartLogger This topic describes how to connect the SmartLogger to multiple inverters. The SmartLogger can connect to multiple inverters through a daisy chain, as shown in Figure 4-21. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 54: Connecting To An Emi

    4.5.2 Connecting the SmartLogger to an EMI That Supports Standard Modbus-RTU Context The SmartLogger can connect to an EMI that supports the standard Modbus-RTU protocol. One SmartLogger can connect to and manage only one EMI. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 55 When the SmartLogger is connected to an EMI and multiple inverters at the same time, connect the EMI to the end of the daisy chain. For details, see 4.4.3 Connecting Multiple Inverters to the SmartLogger. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 56: Connecting The Smartlogger To A Split Emi

    For detailed operations, see the document delivered with the analog-to-digital converter. Step 2 Remove an appropriate length of the steel armor and wire insulation layer from the other end of the cable using a wire stripper, as shown in Figure 4-24. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 57  The EMI cannot be detected automatically. You need to add this device manually on the LCD or WebUI. For details about this operation, see 6.2.34 Managing Devices 7.11.8.1 Connecting Devices. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 58: Connecting The Smartlogger To A Power Meter

    Figure 4-26 Connecting the SmartLogger to a power meter A Power Meter is typically installed indoors, and can be connected to the COM port of the SmartLogger without an RS485 signal SPD. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 59: Connecting To A Plc

    This topic describes how to connect the SmartLogger to a PLC. Context The RS485 port of a PLC is an RJ45 port that should be connected to an RJ45 connector, as shown in Figure 4-27. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 60 There are three RS485 ports in the SmartLogger. For the port descriptions, see Context in 4.4.1 Connecting the SmartLogger to the SUN2000. Figure 4-28 shows how to connect the SmartLogger to the PLC. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 61 Devices.  The Huawei PLC supports auto-negotiation of baud rate 9600 bps/115200 bps. If the PLC networking is used, you are advised to set Baud rate to 115200 bps for the RS485 ports of the SmartLogger to achieve better communication performance.
  • Page 62: Connecting An Ethernet Network Cable

    SmartLogger and network device to be in the same network segment. Correctly set the gateway of the SmartLogger to ensure that the SmartLogger can normally communicate with the network device. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 63: Connecting To A Pid

    Step 2 Connect the other end of the cable to a Surge port of the RS485 signal SPD. For details, see Step 2–Step 4 in Procedure in 4.4.1 Connecting the SmartLogger to the SUN2000. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 64: Connecting The Smartlogger To A Ripple Control Receiver

    4-9describes the definition of the DI ports. Table 4-9 DI port description Port Functions Dry contact input common terminal 1, used for active GND1 power derating for DI1–DI4 DI_1 DI_2 DI_3 Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 65 To enable a normal power grid scheduling function, you need to set the corresponding parameters (Active Power Control or Reactive Power Control) on the embedded WebUI. For details, see 8 Power Grid Scheduling. ----End Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 66 SmartLogger1000 User Manual 4 Electrical Connections Follow-up Procedure Take operations in reversed order to disconnect the SmartLogger from the ripple control receiver. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 67: System Operation

    SUN2000 APP User Manual. Connect the output terminal of the power adapter for the SmartLogger to the power port POWER and the input terminal to the AC socket. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 68: Setting Initialization Parameters

     Use the delivered 12 V power adapter when starting the SmartLogger. Confirm with the local Huawei engineers if using other types of power adapters.  Log in to the SmartLogger on the monitoring panel. When you log in to the Settings page or Maintenance page, an identity authentication is required.
  • Page 69 MM the month, DD the date, hh the hour, mm the minute, and ss the second. NOTICE After the Time is successfully set, this time can be synchronized in all the inverters connected to the SmartLogger. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 70 Visiting some menu requires identity authentication. Therefore, after you set the initialization parameters, change the password immediately to ensure the security of the user account. For details, see Change the Password. ----End Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 71: User Interface

    For the user operation permissions of the menu, see Table 6-3. About ● indicates that the user has permission to operate the menu; ○ indicates that the user does not have permission to operate the menu. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 72 Table 6-3 User operation permissions of the Maintenance menu Maintenance Common User Advanced Special User User Third-Level Fourth-Level Menu Menu ○ ● ● USB Expansion Device Logs ○ ● ● Firmware Upgrade ○ ● ● Batch Upgrade Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 73: Monitoring Operations

    SmartLogger, such as the daily, monthly, yearly, historical, and total energy yield. Procedure  The following table describes the procedure for viewing power station information. The parameter values in the following figures are for reference only. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 74 3. Press to view the running data of the power station. The running data includes the daily, monthly, yearly, historical, and total energy yield. For details, see step 4 to step 8. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 75 Then you can view the total energy yield, CO emission reduction, and revenue corresponding to the CO emission reduction during an hour before this sharp time. NOTE The selected block is displayed in white. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 76 Then you can view the total energy yield, CO emission reduction, and revenue corresponding to the CO emission reduction on the current day. NOTE The selected block is displayed in white. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 77 Then you can view the total energy yield, CO emission reduction, and revenue corresponding to the CO emission reduction in the current month. NOTE The selected block is displayed in white. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 78: Querying Inverter Information

    This topic describes how to query the running information and version of each inverter connected to the SmartLogger. Procedure  The following table describes the procedure for viewing inverter information. The parameter values in the following figures are for reference only. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 79 The follow-up operations are described as follows:  To view the operating data of the inverter, perform step 4.  To view the version of the inverter, perform step 5. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 80 SmartLogger1000 User Manual 6 User Interface Operation Procedure 4. Select Running and press Press to select the target parameter, and then press 5. Select About and press ----End Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 81: Manually Powering On Or Off The Inverter On The Monitoring Panel

    3. Select an inverter and press NOTE SUN2000 (1--2) on the left indicates that the inverter connects to Port 1 of the SmartLogger and the communications address of the RS485 port is 2. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 82 6. Choose Power-On/Off, and press  Perform step 7 if you want to power on the inverter manually.  Perform step 8 if you want to power off the inverter manually. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 83: Sending A Reset Command To The Inverter

    Choose Power-Off, and press b. Enter again to verify your settings. ----End 6.2.4 Sending a Reset Command to the Inverter You can send a reset command to the inverter on the LCD. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 84 SUN2000 (1--2) on the left indicates that the inverter connects to Port 1 of the SmartLogger and the communications address of the RS485 port is 2. 4. Choose Maintenance, and press Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 85: Querying Information About The Emi

    This topic describes how to query the EMI information on the monitoring panel. Procedure  The following table describes the procedure for querying information about the EMI. The parameter values in the following figures are for reference only. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 86 4. Choose Running and press  To view the running information of the EMI, perform step 5 only.  To view the communications address of the EMI, perform step 6 only. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 87: Querying Master Smartlogger Information

    6 User Interface Operation Procedure 5. Choose Running Infomation and press 6. Choose Comm. Address and press ----End 6.2.6 Querying Master SmartLogger Information This topic describes how to query Master SmartLogger information. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 88 The parameter values in the figures are for reference only. Procedure 1. On the default screen, press to enter the main menu. 2. Choose and press 3. Choose Logger (Local) and press view the Master SmartLogger information. ----End Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 89: Querying Slave Smartlogger Information

    To query Slave SmartLogger information, perform the steps described in the following table. The parameter values in the figures are for reference only. Procedure 1. On the default screen, press to enter the main menu. 2. Select and press Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 90: Querying Information About The Modbus Power Meter

    The following table describes the procedure for querying information about the Modbus power meter. The parameter values in the following figures are for reference only. Operation Procedure 1. On the default screen, press to enter the main menu. 2. Select and press Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 91 To view the running information of the power meter, perform step 5 only.  To view the communications address of the power meter, perform step 6 only. 5. Choose Running Infomation and press Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 92: Querying Information About The Dl/T645 Power Meter

    The following table describes the procedure for querying information about the DL/T645 power meter. The parameter values in the following figures are for reference only. Operation Procedure 1. On the default screen, press to enter the main menu. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 93 4. Choose Running and press  To view the running information of the power meter, perform step 5 only.  To view the communications address of the power meter, perform step 6 only. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 94: Setting Dl/T645 Power Meter Parameters

    Operation Procedure 5. Choose Running Infomation and press 6. Choose Comm. Address and press ----End 6.2.10 Setting DL/T645 Power Meter Parameters You can set DL/T645 power meter parameters on the LCD. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 95 Power Meter (3-1) on the left indicates that the power meter connects to port 3 of the SmartLogger and its RS485 communications address is 1. The device status is displayed behind the device name. 4. Choose Settings and press Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 96: Querying Plc Information

    This section describes how to query the running information and version of a PLC connected to the SmartLogger. Procedure  The following table describes the procedure for viewing the information about a PLC. The parameter values in the figures are for reference only. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 97 To view the running information of the PLC, perform step 4 to 6.  To view the version information of the PLC, perform step 7 only. 4. Select Running and press Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 98 SmartLogger1000 User Manual 6 User Interface Operation Procedure 5. Select Running Infomation and press 6. Select Comm. Address and then press Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 99: Setting Plc Running Parameters

    The following table describes the procedure for setting the PLC running parameters. The parameter values in the following figures are for reference only. Procedure 1. On the default screen, press to enter the main menu. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 100 4. Choose Maintenance and press 5. Set User name and Password. NOTE Because of the limited permission, select User name as Advanced User. The initial password for Advanced User is 000001. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 101: Sending A Reset Command To The Plc

    The following table describes the steps for sending a reset command to the PLC. The parameter values in the following figures are for reference only. Operation Procedure 1. On the default screen, press to enter the main menu. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 102 4. Choose Maintenance and press 5. Set User name and Password. NOTE Because of the limited permission, select User name as Advanced User. The initial password for Advanced User is 000001. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 103: Querying Pid Information

    The following table describes the procedure for viewing the information about a PID. The parameter values in the figures are for reference only. Operation Procedure 1. On the default screen, press to enter the main menu. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 104 4 only.  To view the version information of the PID, perform step 5 only. 4. Select Running and press Press to select Runing Infomation or Comm. Address, and then press Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 105: Setting The Pid Module Running Parameters

    The following table describes the procedure for setting the PID module running parameters. The parameter values in the figures are for reference only. Operation Procedure 1. On the default screen, press to enter the main menu. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 106 4. Choose Settings and press 5. Set User name and Password. NOTE Because of the limited permission, select User name as Advanced User. The initial password for Advanced User is 000001. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 107 This mode is applicable only to SUN8000. In the SUN2000, Automatic indicates the N/PE Automatic offset mode. Output Specifies whether Enable Set this parameter to Enable to allow the PID enabled the PID module module output. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 108 DC voltage between PV+ and when Operation PE; if the PV module type is N, the parameter value Mode is set to indicates the highest DC voltage between PV- and Normal or Commissioning. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 109: Manually Powering On Or Off The Pid On The Monitoring Panel

    This topic describes how to power on or off the PID on the monitoring panel. Procedure  The following table shows the procedure for powering on or off the PID on the monitoring panel. The parameter values in the following figures are for reference only. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 110 PID (3-1) in the left figure indicates that the PID is connected to the Port 3 of the SmartLogger, and its RS485 communications address is 1. 4. Choose Settings and press Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 111  Perform step 8 if you want to power off the inverter manually. 7. Power on manually. a. Choose Power-On and press b. Enter again to verify your settings. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 112: Clearing Historical Pid Information

    The following table describes the procedure for clearing historical PID information. The parameter values in the following figures are for reference only. Operation Procedure 1. On the default screen, press to enter the main menu. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 113 4. Choose Settings and press 5. Set User name and Password. NOTE Because of the limited permission, select User name as Advanced User. The initial password for Advanced User is 000001. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 114: Querying Custom Device Information

    The following table describes the procedure for viewing the information about a custom device. The parameter values in the figures are for reference only. Operation Procedure 1. On the default screen, press to enter the main menu. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 115: Querying Alarm Records

    Procedure  The following table describes the procedure for querying active and historical alarms and setting the alarm record sort mode. The parameter values in the figures are for reference only. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 116 Perform step 8 to set the alarm sort mode. 4. On the Active Alarms screen, select the target device name and press to view all the active alarms for this device. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 117 Troubleshooting in the SUN2000 series user manual. 6. On the Alarm History screen, select the target device name and press to view all the historical alarms for this device. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 118 For details about the alarm list of the SUN2000, see the Troubleshooting in the SUN2000 series user manual. 8. On the Sort By page, you can select the way of sorting alarms. ----End Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 119: Setting The System Language

    After passing the permission validation, the system keeps the authentication information for 30 seconds. If you exit from the Settings page and log in again within 30 seconds, no authentication is required. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 120: Setting System Time Parameters

    This topic describes how to set the date, time and date format for the SmartLogger on the monitoring panel. Procedure  The following table describes the procedure for setting the time and date. The parameter values in the following figures are for reference only. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 121 30 seconds, no authentication is required. 4. Choose User Param., and press Here use the pages displayed when you log in to the SmartLogger as Advanced User. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 122: Setting Smartlogger Contrast

    7. On the Date Format page, select a date format, and press ----End 6.2.22 Setting SmartLogger Contrast You can set the SmartLogger contrast on the monitoring panel. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 123 After passing the permission validation, the system keeps the authentication information for 30 seconds. If you exit from the Settings page and log in again within 30 seconds, no authentication is required. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 124: Setting The Currency And Currency Factor

    This topic describes how to set the currency and currency factor for the SmartLogger. Procedure  The following table describes the procedure for setting the currency and currency factor. The parameter values in the following figures are for reference only. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 125 Perform step 5 to set the currency.  Perform step 6 to set the currency factor. Here use the pages displayed when you log in to the SmartLogger as Advanced User. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 126 Select Electricity price/kWh by pressing , and then press b. Set the currency factor by pressing , and then press ----End Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 127: Setting The Co Emission Reduction Coefficient

    After passing the permission validation, the system keeps the authentication information for 30 seconds. If you exit from the Settings page and log in again within 30 seconds, no authentication is required. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 128: Changing A Password

    After the first login, it is recommended that you change the initial password immediately to ensure account security.  You are advised to change the password at least once every half year to prevent unauthorized use of your account, which affects system security. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 129 After the authentication is successful, the system keeps the authentication information for 30 seconds. If you exit from the Settings screen and log in again within 30 seconds, no authentication is required. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 130 Maintenance screen), wait 30 seconds, log in by using the account for which you want to change the password, and perform step 3 to step 7 in the preceding table. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 131: Setting Communications Parameters

    The following table describes the procedure for setting communications parameters. The parameter values in the following figures are for reference only. Operation Procedure 1. On the default screen, press to enter the main menu. 2. Choose and press Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 132 5. Select an RS485 port by pressing and then press There are three RS485 ports: RS485-1, RS485-2, and RS485-3. The corresponding port for RS485-1 is COM1; RS485-2 is COM2; RS485-3 is COM3. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 133  Set the domain name server (DNS) address to the IP address of the router or obtain the DNS address from the network provider. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 134 Server: Fill in the IP address of the NMS server.  Port number: When the SmartLogger connects to the Huawei NMS, the port number is 16100 by default. When the SmartLogger connects to a third-party NMS, set Port number according to the server port enabled in the third-party NMS.
  • Page 135 Therefore, the function of connecting to the NMS using IEC103 is disabled by default to reduce network security risks. Parameters must be set correctly to enable the function. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 136: Restoring Factory Settings

     The displayed language is English by default. Procedure  The following table describes the procedure for restoring factory settings. The parameter values in the following figures are for reference only. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 137 30 seconds, no permission authentication is required. 4. Choose Restore Defaults, and press Here use the pages displayed when you log in to the SmartLogger as Advanced User. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 138: Downloading Device Data Using A Usb Flash Drive

    The following table describes the procedure for downloading data using a USB flash drive. The parameter values in the following figures are for reference only. Operation Procedure 1. On the default screen, press to enter the main menu. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 139 The system takes 5 to 10 seconds to detect the USB flash drive. Then perform the following steps. Here use the pages displayed when you log in to the SmartLogger as Advanced User. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 140: Upgrading Firmware By Using A Usb Flash Drive

    6.2.29 Upgrading Firmware by Using a USB Flash Drive You can upgrade the firmware on the monitoring panel by using a USB flash drive. You can upgrade the firmware of the SmartLogger and devices connected to the SmartLogger. Context Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 141 SmartLogger1000 User Manual 6 User Interface  You have obtained the upgrade package with the help of the supplier or Huawei engineers.  Save the package under the root directory and do not extract the package.  When upgrading the firmware for the SUN2000, change the file name of the package to sun2000_usb.zip.
  • Page 142 On-grid or Shutdown. Check the device status before firmware upgrade. The SmartLogger, inverter, PLC, or PID will restart after being upgraded. (The inverter upgrade screen is used as an example.) ----End Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 143: Batch Upgrade

    The following table describes the batch upgrade procedure. The parameter values in the figures are for reference only. Procedure 1. On the default screen, press to enter the main menu. 2. Choose and press Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 144 USB flash drive. Then perform the following steps. Here use the pages displayed when you log in to the SmartLogger as Advanced User. 5. Choose Batch Upgrade and press 6. Choose SUN2000 and press Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 145: Exporting All Files

    The following table describes the procedure for exporting all files. The parameter values in the figures are for reference only. Procedure 1. On the default screen, press to enter the main menu. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 146 USB flash drive. Then perform the following steps. Here use the pages displayed when you log in to the SmartLogger as Advanced User. 5. Select Export all data files and press ----End Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 147: Importing All Files

    After passing the permission validation, the system keeps the authentication information for 30 seconds. If you exit the screen and log in again within the 30 seconds, no permission authentication is required. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 148: Offline Configuration

    The following table lists the procedure for offline configuration. The parameter values in the following figures are for reference only. Operation Procedure 1. On the default screen, press to enter the main menu. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 149 The system takes 5 to 10 seconds to detect the USB flash drive. Then perform the following steps. Here use the pages displayed when you log in to the SmartLogger as Advanced User. 5. Choose Offline config and press Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 150: Managing Devices

     If you perform Alarm Reset, all active and historical alarms for the selected device will be deleted and the SmartLogger will be enabled to collect new alarm data. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 151 6 User Interface  If Data Clear is performed on Huawei devices such as the inverter and PID module, Alarm Reset must be performed on the SmartLogger and NMS. Otherwise, the SmartLogger cannot collect alarm information generated by the devices after Data Clear is performed.
  • Page 152 RS485 address, search for devices again.  If a device is added, search for the device on the SmartLogger or restart the SmartLogger and then search for the device on the NMS. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 153 7. Choose Single Remove and press twice. NOTE For devices that no longer exist in the PV power system, remove them in time to avoid wasting system resources. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 154 9. Select Addr. Allocate, set the start addresses assigned for RS485-1, RS485-2, and RS485-3, and then press to allocate the addresses. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 155 SmartLogger1000 User Manual 6 User Interface Operation Procedure 10. Press to confirm the address assignment. 11. After the setting of Addr. Allocate is completed, press to adjust addresses. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 156 Before importing a configuration file, you must plug in a USB drive that contains the configuration file.  After importing a configuration file, you need to manually add a third-party device. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 157 SmartLogger1000 User Manual 6 User Interface Operation Procedure 14. Choose Alarm Reset, select a device as required, and press 15. Choose Batch Power-On/Off and press Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 158 SmartLogger1000 User Manual 6 User Interface Operation Procedure 16. Choose Batch Power-On and press 17. Choose Batch Power-Off and press Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 159: Clearing Data

    NMS. Otherwise, the alarm information collected by the NMS and SmartLogger will be different. Procedure  The following table describes the procedure for clearing data. The parameter values in the figures are for reference only. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 160 30 seconds. If you exit the screen and log in again within the 30 seconds, no permission authentication is required. 4. Press , select Data Clear, and press NOTICE Cleared data cannot be restored. Therefore, perform this operation with caution. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 161: Resetting The System

    The following table lists the procedure for resetting the system. The parameter values in the following figures are for reference only. Operation Procedure 1. On the default screen, press to enter the main menu. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 162 30 seconds. If you exit the screen and log in again within the 30 seconds, no permission authentication is required. 4. Choose System Reset by pressing , and press 5. Press ----End Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 163: Querying Product Information

    The following table describes the procedure for querying product information. The parameter values in the following figures are for reference only. Operation Procedure 1. On the default screen, press to enter the main menu. 2. Select and press ----End Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 164: Webui

    Internet Explorer 8 to Internet Explorer 11, Firefox17–Firefox39, or CHROME41–CHROME45 (Windows 7)  Minimum resolution: 1024x768  For Internet Explorer 8, the recommended release is 8.0.7601.17514 or later.  For Internet Explorer 10, the compatible mode is recommended. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 165 Step 2 Choose Tools > Internet Options. Step 3 Click the Connections tab and then click LAN settings. Figure 7-1 LAN setting (1) Step 4 Deselect User a proxy server for your LAN. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 166 To export fault information and operation logs, you need to set the Internet Explorer security. Step 1 Open Internet Explorer. Step 2 Choose Tools > Internet Options. Step 3 Click the Security tab and then click Sites in Trusted sites. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 167 Step 4 Enter the website address of the WebUI (enter the default IP address 192.168.0.10 of the SmartLogger for the first login), click Add, and then click Close. Figure 7-4 Internet Explorer security setting (2) Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 168: Logging In To The Webui

    Figure 7-5 Security risk warning Procedure Step 1 Enter https://XX.XX.XX.XX in the address box of the browser, and press Enter. The login page is displayed. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 169: Webui Menu

    The WebUI varies with the role that you use to log in. ● indicates that the user has permission to operate the menu; ○ indicates that the user does not have permission to operate the menu. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 170 ● ● ● Yield ○ ● ● Running Grid Param. Paramete ○ ● ● Protect Paramete ○ ● ● Feature Paramete ○ ○ ● Power Adjustme ○ ● ○ Tracking System Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 171 About ● ● ● Running Info. ● ● ● Active Alarm ● ● ● Performance Data ○ ● ○ Running Param. ● ● ● About ● ● ● PID-PVBOX Running Info. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 172 Operation ○ ● ● Export Data ● ● ○ Settings User Param. Date&Time ● ● ○ Plant ● ● ○ Currency ○ ● ○ Comm. Ethernet Param. ○ ● ● RS485 Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 173 ○ ○ ● Export Limitation ○ ● ● Maintenance Firmware Upgrade ● ● ● Product Information ● ● ● Security Settings ○ ● ● System Maint. ○ ● ● Device Log Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 174: Icon Description

    Click the Exit icon to log Alarms are classified into out. major, minor, and warning ones. Click the Alarm icon to query an alarm. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 175 Power-off, Idle, or other state in which it is not feeding power into the grid.  The PID device is in Power-off, Idle or other state in which it is not running properly. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 176: Webui Layout

    You can access the alarm page by clicking the number. Details page Displays the details of the queried information or parameter settings. Power grid Displays the current power grid scheduling mode of the scheduling status system. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 177: Overview

    Choose Over View > Plant Running Info. and query information on the displayed page. Figure 7-8 Plant running information The PV plant running information contains only the information about all the Huawei SUN2000s connected to the SmartLogger. 7.7.2 Active Alarm Choose Over View >...
  • Page 178: Plant Yield

    Choose Over View > Plant Yield and query energy yield data on the displayed page. Figure 7-10 Energy yield You can select a tab on the tertiary navigation tree to query the energy yield data of the specific period. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 179: Performance Data

    Otherwise, the file will be unusable. 7.7.5 Device Running Information Choose Over View > Device Running Info. to enter the page. You can check or import the device running information here. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 180: Device Monitoring

    User Manual 7 WebUI Figure 7-12 Device running information 7.8 Device Monitoring 7.8.1 SmartLogger 7.8.1.1 Querying Master SmartLogger-Related Information Choose Monitoring > Logger(Local) and query master SmartLogger-related information on the displayed page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 181: Querying Slave Smartlogger-Related Information

    You can click a tab on the tertiary navigation menu to query master SmartLogger-related information. 7.8.1.2 Querying Slave SmartLogger-Related Information Select a slave SmartLogger on the Monitoring tab page to query its information. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 182: Inverter

    Figure 7-14 Querying slave SmartLogger-related information 7.8.2 Inverter 7.8.2.1 Querying Related Information On the Monitoring tab page, select the inverter to be queried and access the query page to query related information. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 183: Setting Running Parameters (Advanced User)

    7.8.2.2 Setting Running Parameters (Advanced User) Settings Page Because of permission restriction, log in as Advanced User. Select the inverter to be set on the Monitoring page and click the Running Param. tab. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 184 Specifies the inverter working mode  Input grounded (with TF) based on the grounding status at the DC  Input ungrounded side and the connection to the power (without TF) grid.  Input ungrounded (with Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 185 If an AC switch with a residual current detection function is installed outside the inverter, this function should be enabled to reduce the residual current generated during inverter running, thereby preventing the AC switch from misoperations. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 186 Set Strong adaptability to Enable. Power If Power quality optimization  Disable quality mode is set to Enable, the  Enable optimization inverter output current mode harmonics will be optimized. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 187 Crystalline silicon. output PE, thereby effectively reducing Set this parameter to  N-type PID effect of PV modules. P-type output for output P-type PV modules and N-type output for N-type PV modules. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 188 Adjusts the sensitivity of arc  High adaptation mode and adaptation detection.  Moderate AFCI self-test are mode  displayed only when AFCI is set to AFCI Send the AFCI self-test Enable. self-test command manually. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 189 Enable. communication to Disable to  If the inverter reduce power consumption. communicates with the SmartLogger over PLC, this parameter cannot be set to Enable on the WebUI. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 190 The false alarms KTL): String monitor is set asymmetric caused by fixed shadow shading [0.05, 1] to Enable. coefficient can be controlled by changing  Others: [5, this parameter. 100] Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 191 Enable, the inverter shuts down  Enable shutdown after receiving the grounding error signal. If this parameter is set to Disable, the inverter does not shut down after receiving the grounding error signal. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 192 Specifies the operation mode of  Disable running the SUN2000 built-in PID.  Repair mode Specifies whether to enable the  Disable nighttime PID nighttime off-grid repair.  Enable off-grid repair Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 193: Setting Running Parameters (Special User)

    Figure 7-17 Running Param. (special user) The parameter list provided in this document includes all configurable parameters. Configurable parameters vary with the device model and grid code. The actual screen prevails. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 194 [150, 900] for the duration after power grid recovers. 1000 V and 1100 V power grid inverters under the recovery Japanese grid codes. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 195 (cosφ-P) compensation based on the cosφ-P curve. trigger voltage Reactive Specifies the voltage [90, 100] power threshold for exiting compensation reactive power (cosφ-P) exit compensation based on the cosφ-P curve. voltage Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 196 Others: [1 x Vn, 1.36 Vn represents the x Vn] rated voltage.  Level-2 OV Specifies the level-2 1000 V inverter: protection overvoltage protection [50, 600000] time duration.  Others: [50, 7200000] Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 197  In 1000 V protection overvoltage protection /70KTL-C1: [1 x inverters, only threshold. Vn, 1.5 x Vn] the inverters  Others: [1 x Vn, 1.36 marked "-US" x Vn] support this Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 198 Level-5 OV Specifies the level-6 [50, 7200000] protection overvoltage protection time duration. Level-5 UV Specifies the level-5 [0.15 x Vn, 1 x Vn] Vn represents the protection undervoltage protection rated voltage. threshold. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 199 Level-3 UF Specifies the level-3 [50, 7200000] protection underfrequency time protection duration. Level-4 UF Specifies the level-4 [0.85 x Fn, 1 x Fn] Fn represents the protection underfrequency rated frequency. protection threshold. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 200 Specifies the grid 110.0 V, 112.5 V, 115.0 overvoltage overvoltage protection V, and 120.0 V protection threshold. threshold Specifies the grid 0.5s, 1.0s, 1.5s, and 2.0s overvoltage overvoltage protection protection duration. duration Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 201 Refers to a control  Disable feedback module that calculates  Enable module the reactive power based on the offset deviation of grid frequency and promotes frequency offset when islanding occurs. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 202 109.5 V, 110.0 V, 110.5 adjustment power to prevent the grid V, 111.0 V, 111.5 V, point voltage from rising when 112.0 V, and 112.5 V the output voltage exceeds a certain value. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 203 [50%Vn, 92%Vn] This parameter is threshold triggering LVRT. displayed when LVRT is set to Enable. In 1000 V inverters, SUN2000-(8KTL-28K TL) does not support this parameter. Vn represents the rated voltage. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 204  Enable protection function. Passive Specifies whether to enable  Disable This parameter is islanding the passive islanding displayed after the  Enable protection function. Japanese grid code is selected. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 205 Australian AS4777 after the power grid grid code is selected, recovers. and to 300 by default if the Brazilian ABNT NBR 16149 or South African SA_RPPs grid code is selected. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 206 When the output when the power grid Overfrequency frequency is 60 Hz, frequency exceeds a derating is set to the value range is certain value. Enable. [55.00, 65.00]. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 207 16 by default if the gradient of overfrequency derating. Australian AS4777 overfrequenc grid code is selected, y derating and to 15 by default if the Italian CEI0-21 or CEI0-16 grid code is selected. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 208 0% power limit instruction. Reactive Adjusts the inverter (–1.000, 1.000] power output reactive power. compensation (Q/S) Reactive Adjusts the power factor (–1.000, –0.800]U[0.800, power of the inverter. compensation 1.000] (PF) Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 209: Setting A Tracking System

     This function applies only to the 1100 V SUN2000. Because of permission restriction, log in as Advanced User. Choose Monitoring > SUN2000 > Tracking System to access the target page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 210: Setting The Lvrt Characteristic Curve

    Only the 1100 V SUN2000 supports the LVRT characteristic curve, and other models of SUN2000s do not have this function. Because of permission restriction, log in as Special User. Choose Monitoring > SUN2000 > LVRT Characteristic Curve and set the characteristic curve on the displayed page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 211: Plc

    PLC function over an AC power cable. Data is transmitted over the power cable to implement PLC networking. 7.8.3.1 Querying Related Information Choose Monitoring > PLC and query related information on the displayed page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 212: Setting The Sta List

    7.8.3.2 Setting the STA List Because of permission restriction, log in as Advanced User. Choose Monitoring > PLC > STA List and set Baud rate for the listed devices on the displayed page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 213: Networking Settings

    When changing the name of the exported file after the STA list is exported, retain the extension .tar.gz. Otherwise, the file will be unusable. 7.8.3.3 Networking Settings Because of permission restriction, log in as Advanced User. Choose Monitoring > PLC > Networking Settings. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 214 The SN list displays the relevant information of the inverters with PLC STAs that can be connected.  Tap Synchronize, and synchronize the box-type transformer and winding numbers of the PLC CCO to the inverter. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 215: Emi

    After the SmartLogger connects to the EMI, manually add the device. For details, see 7.11.8.1 Connecting Devices. Device Type should be set to EMI. Because of permission restriction, log in as Advanced User. Choose Monitoring > EMI and set EMI parameters. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 216 Read holding register 03H and Read input register 04H are supported. Set this parameter based on the vendor's protocol. Integer and Floating point are supported. Set this parameter Data reporting mode based on the vendor's protocol. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 217 Multiple read and Single read are supported. Start address When Read mode is set to Multiple read, set the start address. When Read mode is set to Multiple read, set the end End address address. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 218: Power Meter

    Because of permission restriction, log in as Advanced User. Choose Monitoring > Meter > Running Param. to access the target page. Set running parameters only for the power meter that supports the DL/T645 protocol. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 219: Pid

    Choose Monitoring > PID and query related information on the displayed page. This document describes the page displayed when the PID01 module is connected as an example. Figure 7-28 Querying PID module-related Information Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 220: Setting Running Parameters

    Set this parameter to Disable if the PID module is not mode offset mode of the required. PID module. N/PE Set this parameter to N/PE if the PID module is required to use voltage output from the inductor virtual midpoint N. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 221 DC position to measure the three-phase (A, B, and C) voltages of the power grid to the ground, and check whether the voltages are the same as the configured values. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 222 Dry contact No. DO1, PID01: Set appropriate ports based on the cable control over which the DO2, and connections between the IMD and the SmartLogger. SmartLogger contact controls the IMD Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 223: Pid-Pvbox

    .tar.gz. Otherwise, the file will be unavailable. 7.8.7.2 Setting Running Parameters Because of permission restriction, log in as Advanced user. Choose Monitoring > PID-PVBOX > Running Param. to enter the target page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 224: Pid-Ssc

    Specifies the output voltage when the PID module works in normal repaired mode. 7.8.8 PID-SSC 7.8.8.1 Querying Related Information Choose Monitoring > PID-SSC and query related information on the displayed page. Figure 7-32 Querying PID-SSC-related information Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 225: Setting Running Parameters

    Modbus-RTU protocol, such as the box-type transformer and environmental monitoring instrument (EMI). Since the protocol information points vary depending on vendors, you need to obtain a protocol information file in .cfg format from Huawei and import the file into the SmartLogger for successfully connecting to a third-party device.
  • Page 226: Querying Related Information

    , or tab on the tertiary navigation menu to query device information. 7.8.9.2 Setting Telecontrol Parameters Select a device on the Monitoring page, and select Telecontrol to go to the page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 227: Setting Teleadjust Parameters

    7 WebUI Figure 7-35 Setting Telecontrol Parameters 7.8.9.3 Setting Teleadjust Parameters Select a device on the Monitoring page, and select Teleadjust to go to the page. Figure 7-36 Setting Teleadjust Parameters Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 228: Querying Historical Data

    Figure 7-37 Historical alarms 7.9.2 Querying Operation Logs Because of permission restriction, log in as Advanced User or Special User. Choose Query > Operation Log and query logs on the displayed page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 229: Exporting Data

    Query > Export Data and export data on the displayed page. Figure 7-39 Exporting data When changing the name of the exported file, do not change the file name extension. Otherwise, the file may be unavailable. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 230 Figure 7-40 Viewing and changing the list separator (1) View and change the list separator. − If List separator is ,, click OK. − If List separator is not ,, change it to ,, and click OK. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 231: Settings

    7.10.1.1 Setting the Date and Time Because of permission restriction, log in as Common User or Advanced User. Choose Settings > Date&Time to access the target page. Figure 7-42 Setting the date and time Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 232: Setting Plant Information

    <>:,`'?()#&\$|%+;~^" in the English half-width status. 7.10.1.3 Setting Gain Parameters Because of permission restriction, log in as Common User or Advanced User. Choose Settings > Revenue to access the target page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 233: Communications Parameters

    Electricity price/kWh indicates the local power price, and is used to calculate the translation gain of the energy yield. 7.10.2 Communications Parameters 7.10.2.1 Setting Ethernet Parameters Because of permission restriction, log in as Advanced User. Choose Settings > Ethernet to access the target page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 234: Setting Rs485 Parameters

    If the IP address is changed, you need to use the new IP address to log in to the system. 7.10.2.2 Setting RS485 Parameters Because of permission restriction, log in as Advanced User or Special User. Choose Settings > RS485 to access the target page. Figure 7-46 RS485 parameters Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 235: Setting Power Meter Parameters

    RM858E, Schneider PM1200, SFERE PD194Z, Socomec COUNTIS E43, and Toshiba S2MS. Meter feedback output Set this parameter based on whether the power meter needs to report the data of the grid-tied point. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 236 If not, set Signal address to Signal address, Number of 65535. Registers, Gain, Data Type, and Unit. Feedback Parameter Set this parameter based on the parameter name to be reported. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 237: Setting Management System Parameters

    Set Server to the IP address or domain name of the management system server.  If the SmartLogger connects to the Huawei management system, retain the default value 16100 for Port number. If it connects to a third-party management system, set Port number based on the server port enabled in the third-party management system.
  • Page 238: Setting Modbus Tcp Parameters

    The SmartLogger can read the information about such third-party devices and upload the information to the NMS, enhancing the PV plant solution. As Huawei inverter devices (such as SUN2000s) support protocols different from third-party devices that use standard IEC103 (such as box-type transformers, combiner boxes, and inverters), they cannot be connected in series on the same RS485 bus.
  • Page 239: Setting Iec104 Parameters

    Figure 7-50 Setting IEC103 parameters  Third-party devices and Huawei devices must be connected to different ports of the SmartLogger. Otherwise, the communication will be abnormal.  The value of IEC103 IP must be consistent with the IP address of the NMS.
  • Page 240: Extended Parameters

    The FTP function is used to access a third-party NMS. The SmartLogger can report the configuration information and running data of the managed plant system through the FTP. A third-party NMS can access Huawei devices with proper configurations. Because of permission restriction, log in as Advanced User. Choose Settings > FTP to access the target page.
  • Page 241: Setting Email Parameters

    Ensure that no password is set between the SmartLogger and the email server. Because of permission restriction, log in as Advanced User. Choose Settings > Email to access the target page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 242 IP address of the SMTP name or IP address of the server are correct. SMTP server are correct. 3. Check whether the network communication between the SmartLogger and DNS is normal. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 243: Port Settings

    When the power supply current is smaller than 1 A, use one DO port.  When the power supply current is larger than 1 A but smaller than 1.6 A, use two DO ports. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 244 Connect one DC power cable of the 3G router to one of the DO ports, power on or off the wireless module by connecting or disconnecting the DO dry contact to control the reset of the 3G router. Figure 7-54 Connecting one DO port Figure 7-55 Connecting two DO ports Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 245: Setting Usb Parameters

    Ground fault audit and vis alm. Figure 7-58 DO Configuration 7.10.4.2 Setting USB Parameters This topic describes how to set USB parameters for resetting an external 3G router over the WebUI. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 246 WebUI to make the external 3G router automatically reset if the SmartLogger fails to connect to the management system, email server, or FTP server within 30 minutes. Because of permission restriction, log in as Advanced User. Then choose Settings > USB. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 247: Alarm Output

    Otherwise, the setting will fail.  After the function is enabled, the DO port status may change and the alarm output may be abnormal if the SmartLogger restarts or powers off. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 248 AFCI Self-Check DC Arc Fault DC Arc Fault Failure Failure Abnormal PV Abnormal PV Software Version Software Ver. Unmatch String Connection String Connection Unmatch Upgrade Failed Upgrade Failed License Expired License Expired Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 249: Dry Contact Remote Shutdown

    The SmartLogger provides eight DI ports, that is, DI1 (GND1) to DI4 (GND1) and DI1 (GND2) to DI4 (GND2). The OVGR can be connected to any DI port, as shown in Figure 7-62. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 250 Table 7-14 describes the DI ports. Table 7-14 DI port description Port Functions Dry contact input common terminal 1, used for active GND1 power derating for DI1–DI4 DI_1 DI_2 DI_3 DI_4 Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 251 Cubicle alarm enabling can be set to Enable or Disable. If Cubicle alarm enabling is set to Enable, if the dry contact signal is effective and the Cubicle is abnormal, an alarm indicating abnormal Cubicle is generated. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 252: Setting Di Parameters

    If Alarm Name has been changed by the user, the new name is displayed on the WebUI but the default name is displayed on the LCD. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 253: Setting Export Limitation Parameters

    DO port and relay on the SmartLogger will be switched off, and the SmartLogger will restore to the initial state. Figure 7-66 Network diagram (without a circuit breaker) Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 254 Communication Specifies the duration for interruption duration determining communication interruption, and is used for automatic shutdown for protection in case of communication interruption. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 255 Log in as Special User and choose Settings > Active power control. Ensure that Active power control is set to Disable. Log in as Special User and choose Settings > Export Limitation. Figure 7-68 Setting export limitation parameters Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 256: Maintenance

    Maintenance > Firmware Upgrade to access the target page. Upload the upgrade file of the device to be upgraded. The upgrade file automatically matches the device name and selects all devices of this type. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 257: Product Information

    Choose Maintenance > Product Information and query SmartLogger information on the displayed page. Figure 7-70 Product information 7.11.3 Setting Security Parameters Choose Maintenance > Security Settings to access the target page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 258: System Maintenance

     Different from the old password 7.11.4 System Maintenance Because of the permission restriction, log in as Advanced User or Special User. Choose Maintenance > System Maint.. Figure 7-72 System maintenance Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 259: Device Log

    The SmartLogger can inspect inverters over the WebUI. Because of permission restriction, log in as Advanced User or Special User. Choose Maintenance > Onsite Test to access the target page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 260: Managing The License

     To load the obtained license to the inverter, tap License loading, as shown in Figure 7-76.  To revoke the license or export the revocation code file, tap License revocation. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 261 Figure 7-76 Loading a license To load a license to the inverter, perform the following steps: Import the license file. Select the inverter whose File Status is To be loaded. Load the license. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 262: Device Management

    Maintenance > Connect Device to access the target page. Figure 7-77 Connecting devices  Huawei devices can be automatically detected or manually added. The EMI, power meter, slave SmartLogger, and third-party devices cannot be automatically detected. You need to add them manually.
  • Page 263: Device List

    CSV file into the WebUI after modification. 7.11.8.3 Exporting Parameters Because of permission restriction, log in as Advanced User or Special User. Choose Maintenance > Export Param. to access the target page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 264: Clearing Alarms

    If you need to clear the active and historical alarms of certain or all devices connecting to the SmartLogger, and re-collect alarm data, perform this operation. Because of permission restriction, log in as Advanced User or Special User. Choose Maintenance > Clear Alarm to access the target page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 265: Data Recollection

    SmartLogger alarms by performing the operation.  If Clear Alarm is performed for the Huawei devices such as the inverter and PID, Alarm Reset must be performed on the NMS. Otherwise the SmartLogger cannot collect alarm data from the devices after alarms are cleared.
  • Page 266: Correcting The Total Energy Yield

    Because of permission restriction, log in as Advanced User or Special User. Choose Maintenance > Adjust total energy yield to access the target page. Figure 7-82 Correcting the total energy yield Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 267: Power Grid Scheduling

    PV plant, that is, to enable the active power derating mode. Because of permission restriction, log in as Special User. Choose Settings > Active power control to access the target page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 268 Because of permission restriction, log in as Special User. Choose Settings > Reactive power control to access the target page. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 269: Active Power Adjustment

    Before setting Active power control mode, set Active power control to Enable. 8.2.1 Disabling Active Power Derating If the inverter is required to run full load, set Active power control mode to Disable active power reduction. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 270: Dry Contact Remote Control

    Before setting dry contact remote control, ensure that the SmartLogger connects to a correct ripple control receiver. For details, see 4.10 Connecting the SmartLogger to a Ripple Control Receiver. Set Active power control mode to Dry contact remote control. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 271: Percentage Fix Limitation

    If the maximum power output of the inverter needs to be controlled, set Active power control mode to Percentage fix limitation. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 272: Remote Scheduling

    Based on the principle of preference of remote scheduling, the SmartLogger sets Active power control mode to Remote scheduling after receiving a scheduling command from the upstream NMS. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 273: Remote Output Control

    Adjustment coefficient: The power value will be sent to the inverter after being multiplied by the preset coefficient. 8.2.5 Remote Output Control Before setting the parameters for remote output control, synchronize the clock source of the server. For details, see 7.10.1.1 Setting the Date and Time. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 274: Reactive Power Adjustment

    .data format from the website of the power company and import the file.  After the SmartLogger connects to the server, you can export the relevant file. 8.3 Reactive Power Adjustment Before setting Reactive power control mode, set Reactive power control to Enable. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 275: Disabling Reactive Power Output

    Before setting dry contact remote control, ensure that the SmartLogger connects to a correct ripple control receiver. For details, see 4.10 Connecting the SmartLogger to a Ripple Control Receiver. Set Reactive power control mode to Dry contact remote control. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 276: Reactive Power Fix Control

    If the PV plant is required to generate at the grid-tied point specified constant reactive power within the power factor range, set Reactive power control mode to Reactive power fix control. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 277: Power Factor Fix Control

    Reactive power control mode to Power factor fix control. Figure 8-12 Power factor fix control Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 278: Q-U Characteristic Curve

    The Q-U characteristic curve supports a maximum of 10 valid points.  Reactive power adjustment time allows you to control the change interval of the reactive power for a grid-tied point. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 279: Cos(Phi)-P/Pn Characteristic Curve

    SmartLogger as a substitute. The SmartLogger delivers the values configured for the characteristic curve to the inverter, which then operates in compliance with the configuration. The SmartLogger no longer adjusts the values. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 280: Remote Scheduling

    NMS, converts them into valid command data identifiable to the inverters, and then sends the data to all the connected inverters. Based on the principle of preference of remote scheduling, the SmartLogger sets Reactive power Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 281: Power Factor Closed-Loop Control

    Before setting the parameters for power factor closed-loop control, ensure that the power meter is connected to the SmartLogger. For details, see 4.6 Connecting the SmartLogger to a Power Meter. Set Reactive power control mode to Pwr factor closed-loop control. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 282: Distributed Power Factor Closed-Loop Control

    Before setting the parameters, ensure that the power meter is connected to the SmartLogger. For details, see 4.6 Connecting the SmartLogger to a Power Meter. Set Reactive power control mode to Distributed power factor closed-loop control. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 283: Pf-U Characteristic Curve

    The control mode of the PF-U characteristic curve is to dynamically adjust the PF value in accordance with the ratio U/Un(%) of the actual grid voltage to the rated grid voltage. Set Reactive power control mode to PF-U characteristic curve. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 284 When configuring the curve, ensure that the U/Un(%) value of a point is greater than the U/Un(%) value of the previous point. Otherwise, the "Invalid input" message will be displayed.  The PF-U characteristic curve supports a maximum of 10 valid points. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 285: Maintenance

    AC power port. power port. 3. Replace the power adapter. 3. Power adapter is faulty. 4. Contact the supplier or Huawei 4. The SmartLogger is faulty. Customer Service Dept. 1. The LCD is faulty. The LCD is Contact the supplier or Huawei Customer off.
  • Page 286 SmartLogger1000 User Manual 9 Maintenance Symptom Possible Cause Measures 1. The button is faulty. The LCD Contact the supplier or Huawei Customer does not 2. The SmartLogger is faulty. Service Dept. respond when a button is pressed. 1. The COM ports are not connected to 1.
  • Page 287: Alarms

    Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 288 The general AC Check whether the disconnection of the Disconn circuit breaker circuit breaker is a normal operation. at the grid-tied Otherwise, contact the service engineer to point is OFF. restore the connection. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 289: Faq

    Anti-crosstalk to Enable, confirm the selected items, and click Submit. Step 6 Click Synchronize to synchronize the transformer station number and winding number to the inverter in the subarray. ----End Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 290 1.7–4.9 (MHz). In other regions, set this parameter to 0.5–3.7 (MHz), 2.5–5.7 (MHz), or 2–12 (MHz) as required. Inverters cannot The PLC board is faulty. Contact Huawei technical support. be networked through PLC. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 291: Which Models Of Power Meters And Emis Are Supported By The Smartlogger

    CEWE Schneider PM1200 SFERE PD194Z Lead LD-C83 MingHua CRDM-830 People RM858E elster A1800ALPHA Mitsubishi LMS-0441E Toshiba S2MS The SmartLogger can connect to only one power meter that uses the Modbus protocol. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 292 Gill MetPak Pro Gill MetPak Pro temperature, PV module temperature, wind direction, and wind speed Ingenieurbü ro Si-RS485TC Ingenieurbü ro Si-RS485TC Total irradiance, ambient temperature, PV module temperature, and wind speed Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 293 JinZhou LiCheng Total irradiance, ambient temperature, PV module temperature, wind direction, and wind speed Sensor ADAM NOTE The sensor-type EMI (current-type or voltage-type) communicates with the SmartLogger through the ADAM analog-to-digital converter. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 294: Disposing Of The Smartlogger

    Disposing of the SmartLogger This topic describes how to dispose the SmartLogger. If the service life of the SmartLogger expires, dispose of the SmartLogger according to the local disposal act for waste electric appliances. Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 295 Storage capacity Stores historical inverter performance data of the last month Language English, Chinese, German, Italian, Japanese, French Dimensions (W x H x D) 225 mm x 140 mm x 50 mm Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 296 Protection level IP20 Installation mode Installed on a wall, desk, or along a guide rail. Port Specifications SmartLogger1000 Ethernet 10/100M, Modbus-TCP RS485 Modbus-RTU Supported Digital parameter input Analog input Relay output Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 297 Table A-1 Monitoring User List Login Mode User Name Initial Password Common User 000001 Advanced User 000001 Special User 000001 Common User Changeme Advanced User Changeme Special User Changeme root Changeme NetEco emscomm /EzFp+2%r6@IxSCv Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 298 Access Terminal Box central coordinator communication digital input digital output enhanced data rate EIRP equivalent isotropically radiated power environmental monitoring instrument Ethernet low power light-emitting diode Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.
  • Page 299 SmartLogger1000 User Manual B Acronyms and Abbreviations power line communication RSTP Rapid Spanning Tree Protocol small form-factor pluggable station Spanning Tree Protocol WEEE waste electrical and electronic equipment Issue 12 (2019-01-15) Copyright © Huawei Technologies Co., Ltd.

Table of Contents