Assembly And Operation - Worx WG163 User Manual

ASSEMBLY & OPERATION
Action
ASSEMBLY
Assembling the Safety Guard
Mounting the Edger Wheel
Installing and Removing the
Battery Pack
Charging the battery pack
More details can be found in
charger's manual
Warning! The charger and
battery pack are specially
designed to work together
so do not attempt to use any other
devices. Never insert or allow me-
tallic objects into your charger or
battery pack connections because
of an electrical failure and hazard
will occur.
OPERATION
Safety ON/OFF Switch
Trimming
12
- Adjusting the Shaft
- Adjusting the Trimmer Head
- Adjusting the Auxiliary handle
- Trimming
- Using the Flower Guard
Edging
- Changing the tool into the
Edging mode
- Edging
Command feeding the line
-Note:Press as needed.
Manually feeding the line
Replacing the trimmer Spool
Manually winding the line
Spool holder (Only for
WG163.3,WG163.5)
Note: Allows for an additional
spool to be stored on the tool.
2 in 1 Cordless Trimmer/Edger
LINE FEEDING/WINDING
INSTRUCTION
Figure
1. Automatic line feed system
When initially switching on the trimmer, a small
See Fig. A1 & A2
length of line is fed out. Each time the tool is started
from rest it will advance about 0.25 inches of trimmer
See Fig. B
line.
A 'clattering' noise will be heard when the lines hit
the Line Cutter. DO NOT BE ALARMED. This is quite
See Fig. C
normal. After about 5 seconds the line will be cut to
the correct length and the noise will reduce as the
motor gains full speed.
If the noise of the line being cut can't be heard, more
line will need to be fed out.
To feed more line, it is first necessary to allow the
trimmer to stop completely; it must come to a
See Fig. D1, D2,
complete rest, then restart, allowing the motor to
D3, D4
reach full speed.
Repeat above until you hear the line hitting against
the Line Cutter.
2.
Your trimmer is equipped with a Command Feed
System. For efficiently feeding the line, just press the
command feed button while the machine is running
See Fig. E
until you hear the 'clattering' noise of the line cutting.
The motor will shut off when pressing the Command
Feed button and will restart when releasing the
See Fig. F
button. During that process the line will automatically
feed additional line for cutting.
See Fig. G1, G2
3. Manually feeding the line (See Fig. M)
See Fig. H
Turn off the trimmer and remove the battery. If
required, line can be fed out manually. To operate,
See Fig. I1
press and release manual Line Feed Button, while
gently pulling out the line until it is long enough to
See Fig. I2
reach the Line Cutter. If the line extends past the Line
Cutter, too much line has been fed out. If too much
line is fed out, remove the Spool Cap and turn Spool
counter-clockwise until the line is at the desired length.
See Fig. J1,
J2, J3
4. Manually winding the line
See Fig. K ( See Fig. O1, O2, O3, O4)
Take approximately 10ft (3m) of line. Insert 5/8 inch
(15mm) of line into the Spool holes and wind line in
See Fig. L
the direction of the arrows on the top of the Spool.
Leave approximately 4 inches (100mm) of line
See Fig. M
unwound and place into the cleat. Ensure that the
line is neatly coiled on the Spool. Failure to do so will
See Fig. N1, N2, N3
impair the efficiency of the automatic line feed. Then
fit the Spool as shown in Fig. N1, N2, N3
See Fig. O1, O2,
O3, O4
See Fig. P
TM
(See Fig. L)
EN