Decanting Your E-Nrg Bioethanol From The - EcoSmart AB Series Installation, Operation And Maintenance Manual

engLiSh
How to Operate the Burner
decanting your e-NRG Bioethanol from the Jerry Can
into the Burner
To view a video of fuelling your Fire, visit our website at
ecosmartfire.com and click on Fire Safety.
WARNING: Fire hazard. Be sure Burner is cool before filling. Let stand
at least 60 minutes after flame is extinguished before refilling.
WARNING: Refuel only through the filling point. Never pour fuel
directly onto the burner.
WARNING: Fire hazard. do not overfill. Fill only to MAx mark. Never
lift the Jerry Can to allow faster flow – insert the spout fully and rest
it on the base of the grid. Used properly, the Jerry Can spout will help
prevent over-filling and spillage.
WARNING: If the fire setting includes multiple burners, all burners
must be OFF and cooled during the filling procedure. Turn all burners
off and allow all burners to cool before refilling a burner. Finish re-
fuelling all burners before lighting each burner.
As an additional safety measure, we recommend that you remove the
burner and check that there is no unexpected fuel collection in the top tray.
the fire company Pty Ltd recommends that the quantity of e-nrg
Bioethanol poured into the burner be burnt until empty rather than
extinguishing the fire early. Extinguishing the fire early can result in a larger
amount of residual fumes in the Burner and a more volatile re-ignition.
When fumes are combined with excess fuel it could be a hazard to
people who are unaware of the fire operation and its condition of use
(e.g smokers). ensure only those who have read the instructions attempt
to operate the burner.
2
1
3
www.ecosmartfire.com
1. remove the transport locking
strip and position the slider
mechanism setting so the
chamber is fully open.
2. inspect inside the burner
mouth to ensure it is clean and
clear of any foreign particles.
3. Access the filling point by
flipping the small lid which is
located in the bottom right
corner of the burner.
XL Series (not applicable for
XS340): the XL Series feature
a spring loading cap. it is
engineered so that the Jerry can
spout is fully enclosed prior to
releasing the fuel supply, thus
allowing filling at a high rate,
whilst eliminating splashing as
the fuel is being decanted.
The XL flame is most visible
when the burner is filled to the
mAX line.
VB2 & XS340
To fill the VB Series, position the
Jerry can spout in the middle of
the burner mouth.
4
8
7
1500m
[59.1in]
e-NRG Bioethanol is the only fuel to use in this appliance.
AB Series:
To fill the AB Series, position the
Jerry can spout in the middle of
the burner mouth.
4. re-position the Burner slider
ensuring the grid work of the
burner is visible through the
filling point. This will clear the
filling point for the insertion of
the Jerry can spout as well
as allowing visual monitoring
of the amount of fuel being
added, according to the volume
markings on the Burner.
5. once ready, carefully place
the Jerry can spout inside
the filling point. NEVER fill
over the maximum level as
indicated on the burner vent
inside the Burner and only fill
to the level that you require for
burning time.
6. use both hands to pour. Place
the palm of one hand on the
top of the nozzle with your
thumb on the green button.
use your other hand to tip
the can vertically and hold it
steady. Press down on the
green button to release the
fuel. To stop the flow, simply
release the green button.
7. When filling is complete, flip
the lid that covers the filling
point so it closes the filling
point.
8. re-position the slider to the
fully open position. check
surrounding area for any
spillage. WARNING: Fire
hazard. Clean up any spilled
fuel before lighting the
burner. See Troubleshooting
page 20 for clean-up
procedure.
9. make sure that the Jerry can
is at least 1500mm [59.1in]
away from the fireplace before
you ignite the fire.