Default Control Change Assignments And Transmission/Reception (Cc#Map) - Korg KingKORG Parameter Manual

KingKORG Parameter Guide
6 .
Default control change
assignments and transmission/
reception (CC#Map)
The table below shows the default assignments of the control changes that
can be assigned by the CC#Map function, and lists the values that are
transmitted and received for each parameter.
TIP: You can make CC#Map assignments in the GLOBAL "g28: MIDI CC#Map
TIP: These messages are transmitted and received on the global channel.
If you are using two KingKORG units to transmit and receive these
parameters, you must set the transmitting and receiving programs to the
same settings.
Section Parameter
Porta.Time
Pitch
Portamento
Voice Unison Voice
Type
CONTROL 1
Osc1
CONTROL 2
Type
CONTROL 1
Osc2
CONTROL 2
Type
CONTROL 1
Osc3
CONTROL 2
OSC1Level
Mixer OSC2Level
OSC3Level
Cutoff
Resonance
Filter
EG1 Int
KeyTrack
Level
Amp
Pan
Attack
Decay
EG1-Filter
Sustain
Release
Attack
Decay
EG2-Amp
Sustain
Release
(→
Assign Value (transmitted)
CC#005 0...127
CC#065 0:Off, 127:On
CC#003 0: Off, 32:2, 64:3, 96:4
0: Off, 1...32: ANALOG, 33...96: DWGS,
CC#008
97...126: PCM, 127: MIC IN
CC#015 0...127
CC#017 0...127
0: Off, 1...32: ANALOG, 33...96: DWGS, 97...126: PCM,
CC#018
127: MIC IN
CC#019 0...127
CC#020 0...127
0: Off, 1...32: ANALOG, 33...96: DWGS, 97...126: PCM,
OFF
127: MIC IN
OFF 0...127
OFF 0...127
CC#023 0...127
CC#024 0...127
CC#025 0...127
CC#074 0...127
CC#071 0...127
CC#079 0/1: –63, 2: –62...63: –01, 64: +00, 65:+01...127: +63
0/1: –2.00 2: -1.93...63: –0.02, 64: +0.00,
CC#028
65: +0.02...127: +2.00
CC#007 0...127
CC#010 Not transmitted
CC#085 0...127
CC#086 0...127
CC#087 0...127
CC#088 0...127
CC#073 0...127
CC#075 0...127
CC#070 0...127
CC#072 0...127
Transmission
Using the KingKORG's knobs or buttons will transmit the control change
messages that are assigned to those parameters.
Control changes will not be transmitted when you use the knobs and
buttons while editing a program.
Reception
When a control change message is received, the value of the assigned
parameter will change.
p.19).
If you're using timbre B, timbres A and B will be changed simultaneously.
If the MIDI channel of timbre B
channel, the parameter of timbre B will not be.
- 35 -
(→ p.4) is different than the global
Value (received)
0...127
0...63:Off, 64...127:On
0...31: Off, 32...63: 2, 64...95: 3, 96...127: 4
0: Off, 1...32:ANALOG, 33...96: DWGS, 97...126:PCM,
127: MIC IN
0...127 (when using the dual, ring, or mic-in oscillators,
0/1: –63, 2: –62...63: –01, 64: +00, 65: +01...127: +63)
(when using the cross modulation oscillator, 0/1: –63,
2: –62...63: –01, 64: +00, 65: +01...127: +63)
(→ p.37 "Mod Harm values for VPM oscillators OSC1, 2,
and 3")
0: Off, 1...32: ANALOG, 33...96: DWGS, 97...126: PCM,
127: MIC IN
0...127 (when using the dual, ring, or mic-in oscillators,
0/1: –63, 2: –62...63: –01, 64: +00, 65: +01...127: +63)
0...127 (when using the cross modulation oscillator,
0/1: –63,2: –62...63: –01, 64: +00, 65: +01...127: +63)
(→ p.37 "Mod Harm values for VPM oscillators OSC1, 2,
and 3")
0: Off, 1...32: ANALOG, 33...96: DWGS, 97...126: PCM,
127: MIC IN
0...127(when using the dual, ring, or mic-in oscillators,
0/1: –63, 2: –62...63: –01, 64: +00, 65: +01...127: +63)
0...127 (when using the cross modulation oscillator,
0/1: –63,2: –62...63: –01, 64: +00, 65: +01...127: +63)
(→ p.37 "Mod Harm values for VPM oscillators OSC1, 2,
and 3")
0...127
0...127
0...127
0...127
0...127
0/1: –63, 2: –62...63: –01, 64: +00, 65: +01...127: +63
0/1: –2.00 2: -1.93...63: –0.02, 64: +0.00,
65: +0.02...127: +2.00
0...127
0/1: L63, 2: L62...63: L01, 64: Center, 65: R01...127: R63
0...127
0...127
0...127
0...127
0...127
0...127
0...127
0...127
MIDI