Korg KingKORG Parameter Manual page 8

KingKORG Parameter Guide
029: VPM Saw
Outputs a modulated sawtooth wave.
030: VPM Square
Outputs a modulated square wave.
031: VPM Tri.
Outputs a modulates triangle wave.
032: VPM Sine
Outputs a modulated sine wave.
CONTROL1: Mod Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[000 . . .127]
This adjusts the depth of the VPM (Variable Phase Modulation) effect.
CONTROL2: Mod Harm(Mod Harmonics)
This specifies the pitch of oscillator B (modulator) as a harmonic multiple of
oscillator A (carrier).
DWGS oscillator
Mod Depth
Detune
These oscillator types produce the simple DWGS (Digital Waveform Generator
System) waveforms found on digital synthesizers such as the Korg DW-8000.
You can generate complex overtones by using VPM (Variable Phase
Modulation) to modulate the waveform.
033-096: DWGS
These are DWGS waveforms from digital synthesizers.
CONTROL1: Detune . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[000 . . .127]
Detunes the relative pitch of the two DWGS oscillators.
Higher values will broaden the pitch difference, creating modulation that makes
the sound richer.
CONTROL2: Mod Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[000...127]
Adjusts the depth of the VPM effect for the DWGS waveform.
PCM oscillator
These oscillator types produce PCM waveforms of acoustic instruments or
digital synthesizers.
097-126: PCM
These are PCM waveforms of acoustic instruments and digital synthesizers.
If you've selected a PCM oscillator, CONTROL 1 and CONTROL 2 are
not available.
MIC IN oscillator
Gain
Mic Input
This lets you use the signal from the rear panel mic jack as the oscillator
waveform.
You can apply the filter, amp, and effects to this audio signal.
If you're using the audio input from the mic jack, pitch-related parameters
are not available.
If you've selected the MIC IN oscillator, CONTROL 2 is not available.
. . . . . . . . . . . . . . . . . . [0 .5, 1 . . .32]
DWGS A
DWGS B
127: Mic In
Outputs the signal from the rear panel mic jack.
CONTROL1: Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[–63...+63]
This adjusts the level of the signal from the mic jack.
At a value of "+00" the input signal will be unchanged (Unity Gain).
If the peak LED lights up, you should also adjust the front panel MIC
LEVEL knob until the signal is no longer peaking.
Oscillator list
Oscillator types 001–032 are excellent analog modeling oscillators. When you
select one of these, the ANALOG LED will light up below the OSCILLATOR
sub-display.
No . Type
001 Saw
002 Pulse
003 Triangle
004 Sine
005 White Noise
006 Pink Noise
007 Blue Noise
008 Res. Noise
009 Dual Saw
010 Dual Square
011 Dual Tri.
012 Dual Sine
013 Unison Saw
014 Unison Squ.
015 Unison Tri.
016 Unison Sine
017 Sync Saw
018 Sync Square
019 Sync Tri.
020 Sync Sine
021 Ring Saw
022 Ring Square
023 Ring Tri.
024 Ring Sine
025 XMod Saw
026 XMod Square
027 XMod Tri.
028 XMod Sine
029 VPM Saw
030 VPM Square
031 VPM Tri.
032 VPM Sine
DWGS
033–096
097–126 PCM
127 Mic In
- 8 -
Parameters
Control1 Control2
Waveform —
PulseWidth —
Waveform —
Waveform —
Decimator Fc Noise Decay
LPF Cutoff Noise Decay
HPF Cutoff Noise Decay
Resonance Noise Decay
Detune —
Detune —
Detune —
Detune —
Detune —
Detune —
Detune —
Detune —
Mod Pitch —
Mod Pitch —
Mod Pitch —
Mod Pitch —
Mod Pitch —
Mod Pitch —
Mod Pitch —
Mod Pitch —
Mod Depth Mod Pitch
Mod Depth Mod Pitch
Mod Depth Mod Pitch
Mod Depth Mod Pitch
Mod Depth Mod Harm
Mod Depth Mod Harm
Mod Depth Mod Harm
Mod Depth Mod Harm
Detune Mod Depth
— —
Gain —