Simplicity Broadmoor 2691467 Operator's Manual page 7

A Control Buttons - MODE (top button), UP (center button), DOWN
(bottom button).
B Clock Display - 12-hour clock with am/pm.
C Blade Icon - Comes on when the Power Takeoff (PTO) is engaged.
D Rider Icon - Comes on when the Cruise Control is engaged.
E Message Display - Tells the operator that the unit requires
maintenance.
F Parking Brake Icon - Comes on when the Parking Brake is engaged.
G Headlight Icon - Comes on when the Headlights are engaged.
H Hour Meter - Shows the total accumulated run hours by default.
When the MODE button is pushed down, the hour meter shows the
trip hours.
I Fuel Level Bars - Comes on to show the approximate level of fuel in
the tank. At two bars, the Fuel Pump Icon will flash to remind you to
add fuel.
J Tachometer with Best Cut Range Icon - Shows the engine speed
from 1000 to 4000 RPM. The Best Cut Range shows the best
performance between the engine speed and the Mower Deck Height
settings.
K Mower Deck Height Bars - Shows the approximate height of the
mower deck.
Functions of the Hour Meter (H, Figure 4)
• By default, the Hour Meter shows the total accumulated
run hours.
• When the meter reaches 1999.9 hours, it automatically
resets to zero.
Trip Hours
• Push the MODE button (A, Figure 4) to show Trip Hours.
• Push the MODE button again and hold for 3 seconds to
reset the trip hours to zero.
Oil Hours
• Push the MODE button (A, Figure 4) two times to show
Oil Hours.
• After you change the oil and filter, push the MODE button
and hold for 3 seconds to reset the oil hours to zero.
Air Filter Hours
• Push the MODE button (A, Figure 4) three times to show
Air Filter Hours.
• After you clean or change the filter, push the MODE
button again and hold for 3 seconds to reset the air filter
hours to zero.
Clock Setting (B, Figure 4)
• Push the MODE button (A, Figure 4) four times to adjust
the clock.
• Push the MODE button again and hold it for 3 seconds to
flash the hour.
• Push the UP or DOWN button to change the hour. AM
and PM will change when the hour setting is adjusted
past 12 o'clock.
• Push the MODE button to flash the minutes.
• Push the UP or DOWN button to change the minutes.
• After you adjust the hours and minutes, push the MODE
button to return to the default clock display.
Note: If you do not push the MODE button after five seconds,
the display will not reset, and the Hour Meter will return to the
total accumulated hours.
Maintenance Messages (E, Figure 4)
Low Battery
• This message appears when a battery voltage problem
occurs.
• The display automatically clears after the battery has
been serviced.
Oil Change
• This message appears after 50 hours of run time since
the previous reset.
• After you change the oil and filter, push the MODE button
two times to show OIL HRS.
• Push and hold the MODE button for 3 seconds to reset
the timer to zero and clear the display.
Air Filter
• This message appears after 25 hours of run time.
• After you clean or change the air filter, push the MODE
button three times to show AIR FILTER HRS.
• Push and hold the MODE button for 3 seconds to reset
the timer to zero and clear the display.
Note: The LOW BATTERY message has priority over other
messages. Service the battery first, then examine the display
for other maintenance messages.
Hour Meter (if equipped)
The hour meter shows the total hours, trip hours, and a digital
clock (Figure 5).
5
Display Total Hours, Trip Hours and Clock
When you start the unit, the Total Hours are shown. The Total
Hours will automatically reset to 0 after 999.9.
1. Push the MODE button (A, Figure 5) for less than one
second to show the Trip Hours.
2. Push the RESET button (B) for more than three seconds
to reset the Trip Hours to 0.
3. Push the MODE button for less than one second to show
the Clock. Push the MODE button for more than three
seconds. The hours will flash on the display. Push the
RESET button to adjust the hours. Push the MODE
7