Defining the 2-Wire Extra Range HD Transmitter Mounting TP-752T/TP-752R Connecting the TP-752T/TP-752R Grounding the TP-752T/TP-752R Connecting the Output to a Balanced/Unbalanced Stereo Audio Acceptor Connecting to TP-752T/TP-752R via RS-232 Setting the Baud Rate Technical Specifications TP-752T / TP-752R – Contents...
Kramer Electronics Ltd. Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront the video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we...
European Advanced Recycling Network (EARN) and will cover any costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular country go to our recycling pages at www.kramerav.com/support/recycling.
Transmission of HDMI signals over standard 2-wire cable. • Cost-effective transmission of video and audio over distances up to 2000 feet. • Upgrading VGA systems to HDMI without having to change the wiring within the walls. TP-752T / TP-752R – Introduction...
Bi-directional RS-232 between the devices, allowing control of the display from the source end/control of a source from the display end. 5V DC +5V DC connector for powering the unit. TP-752T / TP-752R – Defining the 2-Wire Extra Range HD Transmitter...
Page 7
Connect to grounding wire (optional), see Grounding the TP- Screw 752T/TP-752R on page 8. FROM TP-752T CAT 5/6 RJ-45 Port Connect to the RJ-45 port on TP-752T. (Connect via HD15 15-pin HD Connect to the 15-pin HD connector on TP-752T. one of these Connector...
Kramer Electronics Ltd. Mounting TP-752T/TP-752R This section provides instructions for rack mounting TP-752T/TP-752R. Before installing in a rack, verify that the environment is within the recommended range: • Operation temperature – 0° to 40°C (32 to 104°F). • Storage temperature – -40° to +70°C (-40 to +158°F).
TP-752R, connect their power and then switch on the power to each device. Figure 3: Connecting the Transmitter to the Receiver To connect the TP-752T and TP-752R as illustrated in the example in Figure 1. On the TP-752T: Connect the LOOP OUT HDMI connector to an HDMI acceptor (for example, a ...
2. Insert the M3x6 screw through the toothed lock washers and the tongue terminal in the order shown above. 3. Insert the M3x6 screw (with the two toothed lock washers and ring tongue terminal) into the grounding screw hole and tighten the screw. TP-752T / TP-752R – Connecting the TP-752T/TP-752R...
ON (down) OFF (up) 19200 OFF (up) OFF (up) ON (down) 28800 ON (down) OFF (up) ON (down) 38400 OFF (up) ON (down) ON (down) 57600 ON (down) ON (down) ON (down) 115200 TP-752T / TP-752R – Connecting the TP-752T/TP-752R...
2 Power adapters, 2 power cords Specifications are subject to change without notice at www.kramerav.com The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. TP-752T / TP-752R – Technical Specifications...
Page 13
Electronics products, this product must be insured during shipment, with the insurance and shipping charges prepaid by you. If this product is returned uninsured, you assume all risks of loss or damage during shipment. Kramer Electronics will not be responsible for any costs related to the removal or re- installation of this product from or into any installation.
Page 14
SAFETY WARNING Disconnect the unit from the power supply before opening and servicing For the latest information on our products and a list of Kramer distributors, visit our Web site where updates to this user manual may be found. We welcome your questions, comments, and feedback.