Table of Contents
Advertisement
CS
BLOWER MOTOR (Continued)
(5) Install the heater-A/C housing unit (Refer to 24
- HEATING & AIR CONDITIONING/DISTRIBU-
TION/HVAC HOUSING - INSTALLATION).
(6) Run the Heater-A/C Calibration procedure
(Refer to 24 - HEATING & AIR CONDITIONING/
CONTROLS/A/C HEATER CONTROL - STANDARD
PROCEDURE).
DEFROSTER DUCTS
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRECAU-
TIONS COULD RESULT IN ACCIDENTAL AIRBAG
DEPLOYMENT AND POSSIBLE PERSONAL INJURY.
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the instrument panel from the vehicle
(Refer to 23 - BODY/INSTRUMENT PANEL/IN-
STRUMENT PANEL ASSEMBLY - REMOVAL).
(3) Place the instrument panel face down on a
suitable work surface. Be certain to take the proper
precautions to protect the face of the instrument
panel from cosmetic damage.
(4) Remove the four screws that secure the
defroster duct to the instrument panel.
(5) Disconnect the left and right demister hoses
and remove the defroster duct from the instrument
panel.
INSTALLATION
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRECAU-
TIONS COULD RESULT IN ACCIDENTAL AIRBAG
DEPLOYMENT AND POSSIBLE PERSONAL INJURY.
DISTRIBUTION - FRONT 24 - 35
(1) Connect the right and left demister hoses to
the defroster duct and position the defroster duct to
the instrument panel.
(2) Install the screws that secure the defroster
duct to the instrument panel. Tighten the screws to 2
N·m (17 in. lbs.).
(3) Reinstall the instrument panel in the vehicle
(Refer to 23 - BODY/INSTRUMENT PANEL/IN-
STRUMENT
PANEL ASSEMBLY
TION).
(4) Reconnect the battery negative cable.
FLOOR DISTRIBUTION DUCT
REMOVAL
(1) Remove the center console assembly to access
the front floor distribution duct assembly (Refer to 23
- BODY/INTERIOR/CENTER CONSOLE - REMOV-
AL).
(2) Remove the floor distribution duct screws.
(3) Pull the floor distribution duct assembly rear-
ward far enough to disengage the floor distribution
duct from the outlet on the bottom of the heater-A/C
housing unit.
(4) Remove the floor distribution duct assembly
(Fig. 9).
Fig. 9 Floor Distribution Duct Assembly
1 - HEATER A/C HOUSING UNIT
2 - SCREWS
3 - FLOOR DISTRIBUTION DUCT ASSEMBLY
INSTALLATION
(1) Position the floor distribution duct assembly
under the instrument panel center stack and engage
the center floor distribution duct with the outlet on
the bottom of the heater-A/C housing unit.
-
INSTALLA-
Advertisement
Table of Contents
