Accepting Payments
Compliance
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by MagTek could void the user's authority to operate this equipment.
CE STANDARDS
Testing for compliance with CE requirements was performed by an independent laboratory. The unit under test was found compliant with standards
established for Class B devices.
UL/CSA
This product is recognized per UL 60950 1, 2nd Edition, 2011 12 19 (Information Technology Equipment - Safety - Part 1: General Requirements), CSA
C22.2 No. 60950 1 07, 2nd Edition, 2011 12 (Information Technology Equipment - Safety - Part 1: General Requirements).
ROHS STATEMENT
When ordered as RoHS compliant, this product meets the Electrical and Electronic Equipment (EEE) Reduction of Hazardous Substances (RoHS)
European Directive 2002/95/EC. The marking is clearly recognizable, either as written words like "Pb-free," "lead-free," or as another clear symbol(
EMV® is a registered trademark in the U.S. and other countries and an unregistered trademark elsewhere. The EMV trademark is owned by EMVCo, LLC.
The Contactless Indicator mark, consisting of four graduating arcs, is a trademark owned by and used with permission of EMVCo, LLC.
Apple®, Apple Pay®, OS X®, iPhone®, iPad®, iPad Air®, iPad Pro®, Lightning®, and Mac® are trademarks of Apple Inc., registered in the U.S. and other countries. App Store® is a service mark of Apple Inc.,
registered in the U.S. and other countries. iPad mini™ is a trademark of Apple, Inc. IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used by Apple Inc. under license.
How to Swipe Magnetic Stripe Cards
Cardholders should swipe magnetic stripe cards in the MSR
swipe path with the magnetic stripe facing away from the
cardholder and into the device, as shown. Cardholders may
swipe in either direction along the path.
How to Insert Contact Chip Cards
Cardholders should insert chip cards into the chip card slot with
the chip facing the cardholder and toward the slot.
How to Tap Contactless Cards / Devices
Cardholders should tap contactless cards or devices on the landing
zone, indicated by the EMVCo Contactless Indicator symbol on the
device's face. After successfully communicating with the card or
device, kDynamo beeps once. The cardholder may then remove the
card or device from the contactless landing zone. If the cardholder is
using an electronic payment device, ensure the payment device has
NFC turned [On]. Please note, NFC antenna vary by make & model.
MagTek ® Inc., 1710 Apollo Court, Seal Beach CA 90740 p 562-546-6400 | support: 651.415.6800 | support@magtek.com
MAGTEK: Registered to ISO 9001:2015 © Copyright 2018 MagTek, Inc. PN D998200222 rev 10 11/18
).
Need help?
Do you have a question about the kDynamo Series and is the answer not in the manual?
Questions and answers