32: Limiter (Limiter); 33: Gate (Gate); 34: Delay (Delay) - Roland JD-XA Parameter Manual

32: Limiter
(Limiter)
Compresses signals that exceed a specified volume level,
preventing distortion from occurring.
L in
Limiter
R in
Limiter
Parameter Value
Release # 0–127
Threshold # 0–127
1.5:1, 2:1, 4:1,
Ratio
100:1
Post Gain
0–+18 dB
Low Gain -15–+15 dB
High Gain
-15–+15 dB
Level # 0–127
33: Gate
(Gate)
Cuts the reverb's decay according to the volume of the sound
sent into the effect. Use this when you want to create an artificial-
sounding decrease in the reverb's decay.
L in Gate
R in
Gate
Parameter Value
Threshold # 0–127
Mode
GATE, DUCK
Attack
0–127
Hold 0–127
Release 0–127
D100:0W–
Balance #
D0:100W
Level 0–127
L out
2-Band EQ
R out
2-Band EQ
Explanation
Adjusts the time after the signal
volume falls below the Threshold
Level until compression is no longer
applied.
Adjusts the volume at which
compression begins.
Compression ratio
Adjusts the output gain.
Amount of low-range boost/cut
Amount of high-range boost/cut
Output volume
L out
R out
Explanation
Volume level at which the gate
begins to close
Type of gate
GATE:
The gate will close when
the volume of the original sound
decreases, cutting the original
sound.
DUCK (Ducking): The gate will close
when the volume of the original
sound increases, cutting the original
sound.
Adjusts the time it takes for the gate
to fully open after being triggered.
Adjusts the time it takes for the gate
to start closing after the original
sound falls beneath the Threshold.
Adjusts the time it takes the gate to
fully close after the hold time.
Volume balance between the direct
sound (D) and the effect sound (W)
Output volume
34: Delay
(Delay)
This is a stereo delay.
When Feedback Mode is NORMAL:
L in
Feedback
Feedback
R in
When Feedback Mode is CROSS:
L in
Feedback
Feedback
R in
Parameter Value
Dly L/R Sync
msec, NOTE
(Delay Left/Right Sync)
Delay L/R
0–1300 ms, note
(Delay Left/Right)
Phase L/R NORMAL,
INVERSE
(Phase Left/Right)
FbackMode
NORMAL, CROSS
(Feedback Mode)
Feedback #
-98–+98%
200–8000
HF Damp
Hz, BYPASS
Low Gain -15–+15 dB
High Gain -15–+15 dB
D100:0W–
Balance #
D0:100W
Level
0–127
37
Balance D
2-Band
EQ
Delay
Balance W
Delay Balance W
2-Band
EQ
Balance D
Balance D
2-Band
EQ
Delay
Balance W
Delay Balance W
2-Band
EQ
Balance D
Explanation
msec:
The Delay L/R value is
specified in msec.
NOTE:
The Delay L/R value is
specified as a note value.
Adjusts the time until the delay
sound is heard.
Phase of the delay sound
NORMAL: Non-inverted
INVERT:
Inverted
Selects the way in which delay
sound is fed back into the effect.
(See the figures.)
Adjusts the amount of the delay
sound that's fed back into the effect.
Negative (-) values invert the phase.
Adjusts the frequency above which
sound fed back to the effect is
filtered out.
If you do not want to filter out any
high frequencies, set this parameter
to BYPASS.
Amount of low-range boost/cut
Amount of high-range boost/cut
Volume balance between the direct
sound (D) and the delay sound (W)
Output volume
Effects
L out
R out
L out
R out