ESAB Aristo Tig 4000i Instruction Manual
Hide thumbs
Also See for Aristo Tig 4000i:
- Instruction manual (24 pages) ,
- Instruction manual (26 pages)
Related Manuals for ESAB Aristo Tig 4000i
Summary of Contents for ESAB Aristo Tig 4000i
- Page 1 Aristo Tig 4000i Instruction manual 0458 640 301 GB 20110720 Valid for serial no. 802-xxx-xxxx, 803-xxx-xxx. 950-xxx-xxxx...
- Page 2 - 2 -...
-
Page 3: Table Of Contents
1 SAFETY ............2 INTRODUCTION . -
Page 4: Safety
SAFETY Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of equipment. The following recommendations should be ob... - Page 5 There may be potential difficulties in ensuring electromagnetic compatibility of class A equipment in those locations, due to conducted as well as radiated disturbances. - 5 - © ESAB AB 2001 bt23d1ea...
-
Page 6: Introduction
For further information contact the nearest ESAB dealer. ESAB can provide you with all necessary welding protection and accessories. INTRODUCTION The Tig 4000i is a TIG welding power source, which can also be used for MMA welding. -
Page 7: Technical Data
Enclosure class The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid objects or water. Equipment marked IP23 is designed for indoor and outdoor use. - 7 - © ESAB AB 2001 bt23d1ea... -
Page 8: Installation
Lifting instructions With power source With trolley and power source With trolley2 and power source Placing Position the welding power source such that its cooling air inlets and outlets are not obstructed. - 8 - © ESAB AB 2001 bt23d1ea... -
Page 9: Mains Power Supply
The mains cable areas and fuse sizes as shown above are in accordance with Swedish regulations. They may not be applicable in other countries: make sure that the cable area and fuse sizes comply with the relevant national regulations. - 9 - © ESAB AB 2001 bt23d1ea... -
Page 10: Operation
Whether in the event of a loss of power supply or of turning the power source off in the normal manner, welding data will be stored so that it is available next time the unit is started. - 10 - © ESAB AB 2001 bt23d1ea... -
Page 11: Fan Control
If the remote control unit is not to be used, the remote control unit must be disconnected from the power source / wire feed unit, as otherwise it will remain in remote control mode. - 11 - © ESAB AB 2001 bt23d1ea... -
Page 12: Maintenance
CAUTION All guarantee undertakings from the supplier cease to apply if the customer attempts any work in the product during the guarantee period in order to rectify any faults. - 12 - © ESAB AB 2001 bt23d1ea... -
Page 13: Daily
Replace the fan grille with the dust filter. Top up with coolant ESAB's ready mixed coolant is recommended for use. See accessories on page 21. Top up with coolant until it covers half the inlet pipe. CAUTION The coolant must be handled as chemical waste. -
Page 14: Every Year
Spare parts may be ordered through your nearest ESAB dealer, see the last page of this publication. - 14 - ©... - Page 15 NOTES ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................- 15 - notes...
-
Page 16: Diagram
Diagram - 16 - © ESAB AB 2001 bt23e11a... - Page 17 - 17 - © ESAB AB 2001 bt23e11a...
- Page 18 Cooling unit - 18 - © ESAB AB 2001 bt23e11a...
-
Page 19: Ordering Number
0458 640 990 Spare part list Aristo Tig 4000i 0458 819 xxx Instruction manual Aristo 0458 855 xxx Instruction manual Aristo Instruction manuals and the spare parts list are available on the Internet at www.esab.com - 19 - © ESAB AB 2001 bt23o11a... -
Page 20: Spare Parts List
Tig 4000i Spare parts list Item Ordering no. Denomination 0458 398 001 Filter 0458 383 991 Front grill - 20 - ba37s © ESAB AB 2001... -
Page 21: Accessories
0459 491 884 MMA and TIG: rough and fine setting of current Remote control unit T1 Foot CAN ..0460 315 880 For CAN based TIG equipment - 21 - bt23a11a © ESAB AB 2001... - Page 22 Water flow guard 0.7 l/min ....0456 855 880 Coolant (Ready mixed) 50% water and 50% mono-ethylene glycol (10 l) ....0194 230 002 - 22 - bt23a11a © ESAB AB 2001...
- Page 23 NOTES ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................- 23 - notes...
- Page 24 ESAB Romania Trading SRL ESAB VAMBERK s.r.o. SOUTH AFRICA ESAB Mexico S.A. Bucharest Vamberk ESAB Africa Welding & Cutting Ltd Monterrey Tel: +40 316 900 600 Tel: +420 2 819 40 885 Durbanvill 7570 - Cape Town Tel: +52 8 350 5959...