Summary of Contents for Varad i-Security-Touch VS-702
Page 1
Varad International, Inc. VS-702 USER MANUAL Product Name: i-security-touch Model Name:VS-702 1-Way Remote :4751VS 2-Way Transceiver / Antenna :3621VS, Remote function table: Remote command Buttons Conditions P1K1 Disarm P1K2 Lock P1K1 Ignition on Unlock P1K2 Ignition on Silent Arm P0K1...
Page 2
Outside view: MAIN PAGE: Press KEY to display Page 0: press anywhere in touch area to display PAGE ONE PAGE ONE:...
Page 3
Press Forward or Backward button display other page Other PAGES: Button define is same as PAGE ONE,such as : P11K3 is CH5 button in p11 When transmitter received the car alarming will play trigger movies and sound voice: The move will be stopped,if the key pressed Cancel count down: set count down =00:00 Cancel alert time:...
Page 4
Button in other page function table: Buttons Explain Buttons Explain P2K1 Set park time Set park P2K2 P7K2 Set car loge in p0 position Set count down P2K3 P7K3 Set English menu time P2K4 Clear trigger P7K4 Set Spain menu P3K1 Set alert time P8K1...
1. Arm Press button once, system will chirp once, parking lights flash once, lock the doors, starter disabled, window close output 1 sec. (if CH4 programmed), status LED start to flash slowly, will chirp 4 times and parking lights flash 4 times if door or hood or trunk isn’t closed well while arming, and will not detect the door (hood, trunk) open until there are full closed well.
Page 6
When system is alarming or after disarming, if the LED quick flashes several times and then 1 second pauses, it indicates the system has been triggered, and the times the LED flashes indicate the zone that was triggered, as below: Twice: AUX 4 PIN 1 heavy trigger 3 times: AUX 4 PIN 2 heavy trigger 4 times: TRUNK...
Page 7
button twice (see program feature C-2), will unlock the passenger’s doors (activate “2 stage Unlock Output”). If programmed. 13. Lock When system is disarmed and ignition key is on, press button will lock the doors. 14. Unlock When system is disarmed and ignition key is on, press button will unlock the driver’s door.
Page 8
Press to activate channel 5, remote Output pulse time of channel 5 is programmable function (program feature D-1). 22. Channel 6 Press to activate channel 6, remote Output pulse time of channel 6 is programmable function (program feature D-2). 23. Panic In arm or disarm mode and ignition key is off.
Page 9
Pin-code consists of two digits. To disarm system with out remote transmitter or deactivate Anti-hijack mode use PIN-code procedure. Pin-code consists of two digits: X, Y. Factory default 1:1 (X=1, Y=1) To disarming: - turn ignition ON - press override button (X) times - turn ignition OFF then ON - press override button (Y) times - turn ignition OFF...
Page 10
If function on: - pull up hand brake while engine is running - turn ignition key off and take out the key (engine is still running) - engine will run for the programmed duration To stopping engine press button once. Parking flash once for confirm. 31.
Page 11
If start is successful. parking lights flash 3 times Engine runs during “running time”. Then shut down automatically. To stopping engine press button once. Parking flash once for confirm. Engine auto start isn’t available in case of: - engine is running - hood is open - hand brake isn’t activated - Mid-gear procedure isn’t executed (for manual gear only)
Page 12
35. Programming functions FEATURE “A” PROGRAMMING - turn off ignition - press override button 3 times - turn on ignition - parking lights flash and siren chirps 3 times - push the Valet Switch 1 times. - one long chirp with 1 short chirps is heard. You are now in the start feature “A”...
Page 13
Exit feature programming: After 20 sec or turning off ignition system will get out the feature programming setting procedure, parking lights flash 4 times. Press one chip two chip three chip four chip Transmitter LED 1 pulse LED 2 pulse LED 3 pulse LED 4 pulse Button...
Page 14
Exit feature programming: After 20 sec or turning off ignition system will get out the feature programming setting procedure, parking lights flash 4 times. Press one chip two chip three chip four chip Transmitter LED 1 pulse LED 2 pulse LED 3 pulse LED 4 pulse Button...
Page 15
Exit feature programming: After 20 sec or turning off ignition system will get out the feature programming setting procedure, parking lights flash 4 times. Press one chip two chip three chip four chip Transmitter LED 1 pulse LED 2 pulse LED 3 pulse LED 4 pulse Button...
Page 16
Exit feature programming: After 20 sec or turning off ignition system will get out the feature programming setting procedure, parking lights flash 4 times. Press one chip two chip three chip four chip Transmitter LED 1 pulse LED 2 pulse LED 3 pulse LED 4 pulse Button...
Page 17
Transmitter LED 1 pulse LED 2 pulse LED 3 pulse LED 4 pulse Button Default setting Gasoline engine. Diesel engine. Diesel engine. Diesel engine. The glow plug 10 seconds The glow plug The glow plug wire (diesel wait warm-up timer wire must wire must light) not use.
Button Default setting ACC output ACC output ACC output ACC output When remote When hood When hood 5 min before start success engine shut temperature 50℃ temperature 70℃ down Turbo timer Turbo timer Turbo timer TURBO off 1 min. 3 min. 6 min.
Page 19
36. Wires description 1 black loop for select type of gear not cut – auto gear cut – manual gear Set handset PIN code: To check whether the PIN code is right or wrong, can press P1K2, P9K2 to check, if the PIN code is correct then can go to the next step.
Page 20
Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.