Specifications - Sonance SONAMP 275X3 SE Instruction Manual

I N S T R U C T I O N M A N U A L
®
S O N A M P 2 7 5 S E / 2 7 5 X 3 S E
S T E R E O P O W E R A M P L I F I E R
Figure 9: AL1 SAT Module
AL1 Module
( Figures 9 & 10 )
The AL1 — Automatic Line-Level Switcher — module has a default input as
well as a sensing input. When signal is detected at the sensing input, that
signal is fed to the amplifier as well as its output jacks. At the same time a 12V
DC control signal is present on the removable screw connector.
The sensing input has a sensitivity control as well as a delay adjustment which
controls the time the module waits after the signal at the sensing jack subsides
before switching back to the default input.
Figure 10 shows a 275 SE amplifier with the AL1 module in a restaurant
installation. The module's default input is connected to the house restaurant
audio and the sensing input monitors the paging microphone. The output is
feeding a second 275 SE that has the factory-installed BBE module.
Figure10: Restaurant/Bar System Using One Sonamp 275 SE
with an AL1 Module and Another 275 SE with the BBE Module
MICROPHONE PREAMP
RECEIVER
TO SPEAKERS
TO SPEAKERS

SPECIFICATIONS

Rated Power (20Hz – 20kHz) RMS:
Bridged Power (20Hz – 20kHz) RMS:
Midband Power (1kHz, at Clipping) RMS: 114 Watts per channel @ 8 ohms
Bridged Midband Power (1kHz) RMS:
IHF Dynamic Power
(20ms 1kHz Tone Burst)
per IHF RS-490/3.2:
IHF Dynamic Headroom
Total Harmonic Distortion (2-channel mode): 0.05% 20Hz – 20kHz @ 8 ohms
Total Harmonic Distortion (Bridged mode): 0.05% 20Hz – 20kHz @ 8 ohms
I.M. Distortion (SMPTE 4:1) @ 8 ohms:
Signal to Noise Ratio:
Input Sensitivity:
Input Impedance:
Power Requirement (120V version):
Power Requirement (230V version):
Power Consumption (all versions):
Heat Output
(BTU/HR @ 8 ohms):
(BTU/HR @ 4 ohms):
(BTU/HR @ 2.7 ohms):
Dimensions (W x H x D):
Dimensions w/Rack Ears (W x H x D):
Rack Space Requirement:
Shipping Weight:
9
75 Watts per channel @ 8 ohms
125 Watts per channel @ 4 ohms
135 Watts per channel @ 2.7 ohms
250 Watts @ 8 ohms (275 SE only)
140 Watts per channel @ 4 ohms
168 Watts per channel @ 2.7 ohms
270 Watts @ 8 ohms (275 SE only)
120 Watts per channel @ 8 ohms
194 Watts per channel @ 4 ohms
239 Watts per channel @ 2.7 ohms
+1.75 dB @ 8 ohms
+1.9 dB @ 4 ohms
+2.5 dB @ 2.7 ohms
0.08% 20Hz – 20kHz @ 4 ohms
0.15% 20Hz – 20kHz @ 2.7 ohms
0.008% @ 1 watt
0.015% @ 75 watts
105dB below rated output
(A-weighted)
0.7 volts for rated output
(75 watts @8 ohms)
47k ohms, Min.
120 VAC, 50/60Hz
230 VAC, 50/60Hz
500 watts (625VA)
164 (classical); 232 (rock)
294 (classical); 418 (rock)
382 (classical); 542 (rock)
7
16¾" x 3 / " x 15¼"
8
(425mm x 98mm x 387mm)
19" x 3½" x 15¼"
(483mm x 89mm x 387mm)
2U
24 lbs (10.9 kg)