Page 1
Via Benini, 1 40069 - Zola Predosa BOLOGNA - ITALY Hereby declares that: the 961 B-E automation system • is intended to be incorporated into machinery, or to be assembled with other machinery to constitute machinery in compliance with the requirements of Directive 89/392 EEC, and subsequent amendments 91/368 EEC, 93/44 EEC and 93/68 EEC;...
6) FAAC S.p.A. cannot be held responsible for any damage caused by improper use or different from the use for which the automation system is destined to.
ENGLISH FAAC 961 B-E The 961 B-E automatic unit for swing doors is a one-piece unit Table 2: Technical specifications of 960MP Electronic Control consisting of an electromechanical device that allows door Unit + 961 B-E Programming unit opening to be controlled by means of a driving arm. The door...
Page 4
ENGLISH 2. ELECTRICAL SETUP (fig. 2a Standard system) MOUNTING THE DRIVING ARMS 961 B-E operator 3.3.1 MOUNTING THE PUSHING ARTICULATED ARM (fig. 5) Microwave radar / Passive infrared sensor 1) Close the door. T20E external key-switch (KEY command) 2) Free arms (1) and (2) by pulling apart the coupling (3) manually as shown in fig.
N.B.: To repeat the initialisation procedure hold down the RESET button (fig. 11 - ref. 4) for more than 4 seconds. 5. 961 B-E PROGRAMMING UNIT 5.1 LAYOUT AND DESCRIPTION Signalling LEDs (see Table 5) with 960 MP electronic control unit Signalling buzzer (see section 5.4.)
Page 6
ENGLISH 5.3. PROGRAMMING THE MICROSWITCHES (fig. 10) S1 S2 S3 S4 S5 S6 S5-S6 Inactive Overclosing stroke Initialisation Inactive procedure Active Standard Non-standard Function switch “Push and Go” position “0” Active Manual N.B.: Press RESET after every programming operation. Fig. 10 Inactive Night The programming unit has a series of microswitches which...
Page 7
ENGLISH 1 2 3 CODIS Fig. 13 Fig. 12 Fig. 14 L = screened cable 2 x 0.5 mm 2; 50 m max. max. 0,5A/24 Vdc max. 0,5A/24 Vdc 9 10 < 0,5A < 0,5A Fig. 15 Fig. 17 Fig. 16 9 10 BROWN 11 12 13 14 15 16...
7. FUNCTION SWITCH opening movement of the door. The 961 B-E operator has a 3-position function switch (0-1-2) To install more than one CLOSURE safety device, connect mounted on one of the end covers (fig. 1 - ref. 12). This cover the N.C.
Page 9
ENGLISH 8. “CODIS” EXTERNAL PROGRAMMING UNIT (OPTIONAL) STATUS LEDS LEDS DI SEGNALAZIONE The 961 B-E automation unit can also be controlled by an external programming unit in place of the function selector and of the 961 B-E programming unit. RESET...
ENGLISH When the “-” pushbutton is pressed, the door speed, Table 7: programming functions opening excursion and pause time are decreased. FUNCT.NO. LEDS FUNCTIONS LED 6 Return to Level I (operating functions) by pressing the “+” and “-” pushbuttons simultaneously. OFF OFF OFF OFF OFF Output Level III Notes: - The CODIS automatically returns to Level I after 2...
Page 11
In this case, Level II is inhibited, and the settings (speed, pause times, etc.) must be performed by function 16 means of the internal 961 B-E programming unit. Opening commands stored (interlock): in interlock operation, CODIS - permanent installation: the CODIS is installed it is not necessary to wait until one door has closed before permanently;...
ENGLISH Table 8 24 25 LEDS FAILURE NOTE ON OFF OFF OFF OFF Motor fault 24 25 Fig. 26 OFF ON OFF OFF OFF Governor and brake fault ON ON OFF OFF OFF Initialisation process not possible Opening angle insufficient OFF OFF ON OFF OFF Initialisation process not possible Opening angle excessive...
23 24 25 travel must be initialised. Proceed as follows: - Remove the arm from the drive shaft. - Set all the microswitches of the 961 B-E programming unit Fig. 28 (fig. 9 - ref. 4) to position OFF. - Rotate all the adjusting trimmers (fig. 9 - ref. 3) counterclockwise all the way.
Page 14
(LED lit steadily). See fig. 2. DESCRIPTION The 961 B-E automatic unit for swing doors is a one-piece unit consisting of an electromechanical device that allows door opening to be controlled by means of a driving arm. The door POSITION “1”: AUTOMATIC...
Need help?
Do you have a question about the 961 B-E and is the answer not in the manual?
Questions and answers