Table of Contents
Related Manuals for Zephyr ALL-M90BBX
Summary of Contents for Zephyr ALL-M90BBX
- Page 1 Layers Island ALL-M90BBX ALL-M90BWX ALL-E42BBX ALL-E42BWX Duo Island ADL-M90BSX ADL-E42BSX RANGE HOOD - Installation and use instructions ENGLISH........3 FRANÇAIS........29...
- Page 2 INSTALLING THE DUCTWORK: INTERNAL BLOWER ROOF CAP NOTE: To reduce the risk of fire, use only metal ductwork. 6” ROUND DUCT 1. Decide where the ductwork will run between the hood and the outside. 2. A straight, short duct run using a minimum 6”...
- Page 3 INSTALLING THE INTERNAL BLOWER NOTE: The following instructions are for installing the internal blower only. Install this range hood only with internal blower model CBI-290A or CBI-600A. 1. Remove the 6” metallic flange provided on the blower’s air outlet (the flange may already be pre-installed) (Fig.8).
-
Page 4: Internal Blower Wiring
INTERNAL BLOWER WIRING Note: This range hood must be properly MOUNTING SCREWS grounded. The unit should be installed by a 3.9x6mm qualified electrician in accordance with all applicable national and local electrical codes. 1. Secure capacitor box screwing the (2) 3.9x9.5 mm screws (Fig.13A) 2. - Page 5 REMOTE BLOWERS (EXTERNAL AND IN-LINE) CAUTION: To reduce risk of fire and electric shock, install this range hood only with External Blower Model CBE-1000, and In-Line Blower Model PBN-1000A. Other blowers cannot be substituited. INSTALLING THE DUCTWORK: REMOTE BLOWER NOTE: To reduce the risk of fire, use only metal ductwork. 1.
- Page 6 INSTALLING THE REMOTE MOUNTING SCREWS BLOWER 3.9x6mm NOTE: The following instructions are for preparing the hood for use with external or in-line blower models CBE-1000 or PBN- 1000A. For blower installation details refer to manual included with the blower. 1. Remove the blower plate unscrewing the (4) 3.9x9.5 mm screws (Fig.15).
-
Page 7: Remote Blower Wiring
REMOTE BLOWER WIRING 1. Remove the covers from the wiring boxs and remove one knockouts. 2. Run 4-wire plus ground power cable from the remote blower to the remote blower wiring box marked “motor connection” (Fig.18B). 3. Feed 6” of cable through the knockout opening and secure the cable to the wiring box with an appropriate connector. -
Page 8: Install Support System
INSTALL SUPPORT SYSTEM DRYWALL CROSS FRAMING Remove the plastic protective film from all exterior surfaces, decorative flues and filters, 10” prior to final installation. 1. At hood location, install 2 x 4 or larger cross framing between ceiling joists using dimensions shown. -
Page 9: Install The Hood
INSTALL THE HOOD Insert 8 screws (3.9x6mm), located in the Hardware Package (Fig. 21). DUCTED INSTALLATION ONLY Note: Rooms with 10 to 12 foot ceiling require duct cover extension/support frame model Z1C-02LL, available from MOUNTING your local dealer. SCREWS 3,9x6 mm Discard the duct covere extension/ support frame supplied with the range hood and replace it with the longer duct... - Page 10 CONNECT THE DUCT MOUNTING SCREWS COVERS 3,9x9,5mm 1. Secure the two upper duct covers to support frame with (4) 3.9 x 9,5 mm screws UPPER DUCT (Fig.24). COVER Vents may be exposed on 10 to 12 foot ceilings. 2. Secure the two lower duct covers parts to the support frame by overlapping the lateral magnets (Fig.25).
-
Page 11: Mesh Filters
MESH FILTERS NOTE: prior to use, remove protective film from the filter frame. DUCTED AND NON-DUCTED HOODS 1. To remove the MESH filter, pull down on latch tab to disengage the filter from the hood. Tilt the filter downward and remove (Fig.26). -
Page 12: Replacement Parts
HOOD DESCRIPTION PART# REPLACEMENT PARTS Metal Mesh Filter 50200031 Metal Mesh Filter 50200033 OPTIONAL ACCESSORIES Recirculating Kit ADL-ALL ZRC-01LL Replacement Charcoal Filters ADL-ALL Z0F-01AC Extension Flue up to 12’ ADL-ALL Z1C-02LL To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.8368 - 26 -...