Related Manuals for STIEBEL ELTRON DHM 6 220
Summary of Contents for STIEBEL ELTRON DHM 6 220
- Page 1 OPERATION AND INSTALLATION Hydraulically controlled mini instantaneous water heater » DHM 6 220...
-
Page 2: Table Of Contents
- Ensure the appliance can be separated from the Maintenance ������������������������������������������������ 14 power supply by an isolator that disconnects all Specification ������������������������������������������������ 15 poles with at least 3 mm contact separation. GUARANTEE - The specified voltage must match the mains voltage. ENVIRONMENT AND RECYCLING | DHM 6 220 www.stiebel-eltron.com... -
Page 3: Operation
„Installation / Maintenance / Draining the appliance“. 1.1.1 Structure of safety instructions KEYWORD Type of risk Here, possible consequences are listed that may result from failure to observe the safety instructions. f Steps to prevent the risk are listed. www.stiebel-eltron.com DHM 6 220 |... - Page 4 CAUTION Failure to observe this information may result in non-seri- ous or minor injury. Units of measurement Note Unless specified otherwise, all dimensions are given in | DHM 6 220 www.stiebel-eltron.com...
-
Page 5: Safety
There is a risk of scalding at outlet temperatures in ex- Test symbols cess of 43 °C. See type plate on the appliance. DANGER Electrocution Any damaged power cables must be replaced by a qual- ified electrician. This prevents potential hazards from arising. www.stiebel-eltron.com DHM 6 220 |... -
Page 6: Appliance Description
The water is heated. The water temperature can be f Regularly descale or replace the special aerator (see chapter adjusted at the tap: “Appliance description / Accessories”). For the start volume, see chapter “Specification / Data table / On”. | DHM 6 220 www.stiebel-eltron.com... -
Page 7: Troubleshooting
Material losses Observe the max. permissible inlet temperature. Higher DHM 6-220 Nr.: 000000-0000-000000 temperatures may damage the appliance. You can limit the inlet temperature by means of a central thermostatic valve (see chapter "Appliance description / Accessories"). www.stiebel-eltron.com DHM 6 220 |... -
Page 8: Appliance Description
A safety valve is not required. - Connection hose 3/8, 500 mm long, with gaskets* - Tee 3/8* Taps - Company logo for oversink installation f Use suitable taps (see chapter “Appliance description / Accessories”). *for the connection as pressure-tested appliance | DHM 6 220 www.stiebel-eltron.com... -
Page 9: Installation
The appliance is only suitable for undersink installation (water connections at the top). DANGER Electrocution Protection rating IP25 is only ensured if the appliance back panel is fitted. f Always fit the appliance back panel. www.stiebel-eltron.com DHM 6 220 |... - Page 10 f Undo the cover fixing screws by two turns. f Undo the snap fastener using a screwdriver. f Remove the appliance cover with the heater towards the front. | DHM 6 220 www.stiebel-eltron.com...
- Page 11 Fit the tap according to the illustration. For this, also observe the tap operating and installation instructions. Material losses When making the connections, counter the torque on the appliance using a size 14 spanner; see chapter "Installa- tion alternatives / Undersink installation". www.stiebel-eltron.com DHM 6 220 |...
-
Page 12: Commissioning
(in the case of a power cable with plug), ensure that the socket is freely accessible after the appliance has been 11.2 Appliance handover installed. f Explain the appliance function to users and familiarise them with its operation. | DHM 6 220 www.stiebel-eltron.com... -
Page 13: Shutting Down
12. Shutting down f Isolate the appliance from the power supply by means of the fuse/MCB in your fuse box or by pulling the power cable plug from the socket. f Drain the appliance (see chapter “Maintenance”). www.stiebel-eltron.com DHM 6 220 |... -
Page 14: Maintenance
1 1-pole safety pressure limiter f Close the shut-off valve in the cold water inlet line. f Open the draw-off valve. f Undo the water connections on the appliance. | DHM 6 220 www.stiebel-eltron.com... -
Page 15: Specification
Cold water inlet Male thread G 3/8 A freeze and cause damage. DHW outlet Male thread G 3/8 A Replacing the power cable f If replacing the cable, use a power cable with 4 mm² cross-section. www.stiebel-eltron.com DHM 6 220 |... - Page 16 SpECifiCaTiON 15.2 Wiring diagram 15.3 Increasing the temperature 15.2.1 DHM 6 220, 1/N/PE ~ 220 V V > p > X Flow rate in l/min Y Temperature increase in K 15.4 Application areas For the specific electrical resistance and specific electrical conductivity, see “Data table”.
- Page 17 Max. permissible inlet temperature °C l/min > 2,6 Pressure drop at flow rate 0,09 Flow rate for pressure drop l/min DHW delivery l/min Δϑ at DHW delivery Hydraulic data Rated capacity Versions Oversink installation Undersink installation www.stiebel-eltron.com DHM 6 220 |...
-
Page 18: Guarantee
This will not affect warranties issued by any importers. Environment and recycling We would ask you to help protect the environment. After use, dispose of the various materials in accordance with national regulations. | DHM 6 220 www.stiebel-eltron.com... - Page 19 GUARANTEE | ENVIRONMENT AND RECYCLING www.stiebel-eltron.com DHM 6 220 |...
- Page 20 Deutschland Verkauf Tel. 05531 702-110 | Fax 05531 702-95108 | info-center@stiebel-eltron.de Kundendienst STIEBEL ELTRON GmbH & Co. KG Tel. 05531 702-111 | Fax 05531 702-95890 | kundendienst@stiebel-eltron.de Dr.-Stiebel-Straße 33 | 37603 Holzminden Ersatzteilverkauf Tel. 05531 702-120 | Fax 05531 702-95335 | ersatzteile@stiebel-eltron.de Tel.