Related Manuals for B2 Audio RAGE SERIES
Summary of Contents for B2 Audio RAGE SERIES
- Page 1 2500.1 rage 1200.6 rage 600.4 product id: Rage25001D19 rage12006df19 rage6004df19...
-
Page 2: Troubleshooting
Don’t blow a fuse, keep calm. The next era comes with our rede ned levels. The Rage series is “The increased Desire for B2 audio”. Starting out with 3 amplifers at the same time, the Rage should cover any need for near any type of user. Mono, 4ch or even 6 ch ampli cation, no problem, Rage covers it all. -
Page 3: Design Features
Design features rage 2500.1 rage 1200.6 rage600.4 Circuit Configuration: HI-EF Class D Hi-ef Class D fr hi-ef Class D fr Frequency Response: 15 ~ 200 Hz 10 Hz ~ 25 Khz 10 Hz ~ 27 khz Signal to Noise Ratio: >... -
Page 4: Panel Layout
Panel layout rage2500.1 INPUT REMOTE LEVEL CONTROL PORT RCA signal input for left & right channel. Connection of external signal level control. A minimum of 0.1V input signal is required for correct CAUTION, the ampli er needs to be gained in accordance operation. -
Page 5: Power Terminal
Power & speaker terminal rage2500.1 POWER SPEAKER Keep ground as short as possible and as use the adequate AWG to achieve optimal performance. The minimum ohm load is 1 ohm. In strapped mode, the ohm load is 2 ohm. power terminal GND (Ground connection) +12v (Power connection) Connects to the vehicle’s chassis. - Page 6 Panel layout rage1200.6 INPUT CH1~CH6 Gain (6v~0.2v) CH3/4 RCA signal input for left & right on channel speci ed. Adjusts signal input voltage from the input source A minimum of 0.2V input signal is required for correct to match the ampli ers input stage. 0.2V ~ 6V is the operational voltage.
-
Page 7: Speaker Output Terminals
P0wer & speaker terminal rage1200.6 BRIDGED BRIDGED POWER BRIDGED SPEAKER pro led onnects to the vehicle’s chassis. Keep as short as Ampli er has gone into protect mode. possible (< 20” / 50 cm). Use minimum 4AWG cable The malfunction could be caused by speaker short, optimal operation. - Page 8 Panel layout rage600.4 INPUT CH1~CH4 Gain (6v~0.2v) CH3/4 RCA signal input for left & right on channel speci ed. Adjusts signal input voltage from the input source A minimum of 0.2V input signal is required for correct to match the ampli ers input stage. 0.2V ~ 6V is the operational voltage.
- Page 9 Power & speaker terminal rage600.4 SPEAKER BRIDGED BRIDGED pro led onnects to the vehicle’s chassis. Keep as short as Ampli er has gone into protect mode. possible (< 20” / 50 cm). Use minimum 4AWG cable The malfunction could be caused by speaker short, optimal operation.
- Page 10 Strapped control panel setting Bass remote master amplifier output power. Follow the instructions carefully as it can cause harm to your system if done incorrect. slave amplifier Speaker impedance 2 Ohm ~ 16 Ohm will reach thermal at a faster rate & will eventually go into protect. Strapped impedance load under 2 ohm is not warranted!
- Page 11 Strapped control panel setting Bass remote master amplifier output power. Follow the instructions carefully as it can cause harm to your system if done incorrect. slave amplifier Speaker impedance 2 Ohm ~ 16 Ohm will reach thermal at a faster rate & will eventually go into protect. Strapped impedance load under 2 ohm is not warranted!
- Page 12 Strapped speaker connection rage2500.1 master amplifier POWER SPEAKER Speaker impedance 2 Ohm ~ 16 Ohm will reach thermal at a faster rate & will eventually go into protect. Strapped impedance load under 2 ohm is not warranted! slave amplifier POWER SPEAKER step 1.
- Page 13 accu8 crossovers rage2500.1 rage1200.6 rage600.4 CLick settings for LPF - hpf - subsonic rage2500.1 rage1200.6 rage600.4 subsonic hpf ch1-4 ch5-6 1. 20 Hz 10 Hz 50 Hz 20 Hz 50 Hz 20 Hz 50 Hz 5. 21 Hz 13 Hz 65 Hz 25 Hz 55 Hz...
- Page 15 audio precision charts rage2500.1 0.05 0.02 0.01 1.565k Sweep Trace Color Line Style Thick Data Axis Comment Cursor1 Cursor2 Magenta Solid Anlr.THD+N Ratio Left MODEL-------------RAGE2500.1 VOLTAGE-----------14.4 ±0.2V Current: 126A 0.05 0.02 0.01 2.596k Sweep Trace Color Line Style Thick Data Axis Comment Cursor1...