70 name & number caller-id telephone with speakerphone (25 pages)
Summary of Contents for Bell Excursion 39280
Page 1
Excursion 39280 ® Congratulations on your selection of the Excursion 39280 from Northwestern Bell Phones. This quality 900MHz cordless ® telephone, like all Genuine BELL products, has been designed to give you many years of continuous service and represents the best value for your money.
IMPORTANT SERVICE INFORMATION Read this manual before attempting to setup or use this instrument. It contains important information regarding safe installation and use. Keep this manual for future reference. Also save the carton, packing and proof of purchase to simplify and accelerate any needed action.
SAVE THESE INSTRUCTIONS product where the cord will be abused by persons walking on it. Do not overload wall outlets and IMPORTANT SAFETY extension cords as this can result in INSTRUCTIONS the risk of fire or electric shock. When using your telephone equipment, 10.
If the product exhibits a Use only the 3.6V, 450mAh, Ni-Cd distinctive change in battery pack . The type NO. is 3SN- performance. AA45-S-X 13. Avoid using a telephone (other than Do not dispose of the battery in a a cordless type) during an electrical fire.
SAVE THESE INSTRUCTIONS opportunity to maintain uninterrupted service. FCC NOTICE If you experience trouble with the telephone, please contact VTC The FCC requires that you be advised of Service & Manufacturing Co., Inc at certain requirements involving the use of (800) 888-8990 or write to: VTC this telephone.
Page 6
Privacy of communications may not be ensured when using this phone. Changes or modifications not expressly approved in writing by Northwestern Bell Phones may void the user's authority to operate this equipment. Some cordless phones operate at frequencies that may cause interference to nearby TVs and VCRs;...
Page 7
® Excursion 39280 CONTROLS DIAGRAM Handset Antenna INUSE/BATT LOW LED Indicator Handset Receiver RINGER TALK Button OFF/ON Switch Flash Button VOL(Volume) MEMO Button Button Handset Jack RE/PA(Redial/Pause) Button Tone(*) Button SCAN Button MUTE Button PAGE Button IN USE/ CHARGE LED Indicator Base Unit Antenna/ Visual ringer indicator...
Memory(MEMO) Button – Used for DESCRIPTIONS storing/retrieving phone numbers Handset Controls: to/from the 10 memory locations. Handset Antenna - A fixed antenna. Charge Contacts – For charging the IN USE/BATT LOW LED Indicator- - handset battery pack. We recommend (IN USE) Flashes rapidly while auto- that you clean these contacts periodically scanning.
TONE/PULSE Switch - A switch pack should be fully charged overnight located on the rear side of the base unit, prior to initial use. which allows you to set the dialing mode to either Tone dialing or Pulse(rotary) Belt Clip Installation With the back of handset facing up, dialing.
inner slots of the base unit as shown lines, only leaving the smooth part in Figure 4. of the screw head outside the wall. Press the middle locking hooks of Install the wall mount bracket into the mounting bracket while pushing the base unit as previously discussed the back of the mounting bracket in Figures 3-6.
UTION: You must use a Class II, 120 Volt AC/9 Volt DC adaptor that delivers at least 200mA. The center tip must be positive and the plug must correctly fit Headset the unit’ s DC 9V jack. Jack Plug the AC adaptor into a standard AC outlet.
Page 12
desired phone number on the Channel Scan (Manual Scan) • handset keypad. If the existing channel becomes noisy or starts having radio Receive a Call interference, press the SCAN button If the handset is on the base: repeatedly until a clear channel is •...
Page 13
programmed into the memory. Each 4- USE/BATT LOW LED indicator second pause occupies one digit of the lights solid. available 16 digits per memory location. Press the MEMO button. Press the memory location (0-9) on Memory Dialing the keypad for the number you have You can store and recall up to 10 stored.
Low Battery Warning TECHNICAL When the handset battery voltage level is INFORMATION low, the IN USE/BATT LOW LED This cordless phone uses radio indicator on the handset will start to frequencies to allow mobility. There are blink and a beep sounds. Return the certain difficulties in using radio handset to its cradle on the base unit for frequencies with a cordless telephone.
Page 15
improve the operating range of the batteries can limit the range of unit. cordless operation. • Keep the base unit away from electrical equipment. Radio Frequency Interference (RFI) is sometimes generated by these appliances, which can cause a degradation in cordless reception. •...
TROUBLESHOOTING SYMPTOM SOLUTION • No dial tone Check to see if the handset battery pack is connected inside the handset battery compartment. • Make sure that the adaptor plug is connected to the base unit. • Check for the telephone line cord connections, Ensure that both connectors are plugged securely on the jacks.
Page 17
• No link between You may have taken the handset at a distance away from the the base and base that is beyond its normal operating range. Refer to the handset section of “Operating Range” in the manual for more details. •...
Page 18
Distributed Exclusively Worldwide by Unical Enterprises, Inc., Industry, California, USA 39280/061703A-2 www.nwbphones.com 061703A-2 OWNER’ S MANUAL # 39280 ver. 061703A-1 Page: 17 ENGLISH VERSION...
Need help?
Do you have a question about the Excursion 39280 and is the answer not in the manual?
Questions and answers
Change message on phone