Advertisement
INSTRUCTIONS FOR INSTALLATION & SERVICING
IMPORTANT: ENSURE THAT THE APPLI
ANCE IS CORRECTLY ADJUSTED FOR
THE GAS TYPE AND CATEGORY
APPLICABLE IN THE COUNTRY OF USE.
REFER TO DATA BADGE AND TECHNI
CAL SPECIFICATIONS AT THE FRONT
OF THE BOOKLET.
FOR DETAILS OF CHANGING BETWEEN
GAS TYPES, REFER TO SECTION 18.
1.
SAFETY PRECAUTIONS
1.1
This appliance must be installed in accor-
dance with the rules in force, and used
only in a sufficiently ventilated space.
Please read these instructions before
installation and use of this appliance.
1.2
These instructions must be left intact with
the user.
1.3
Do not attempt to burn rubbish in this
appliance.
1.4
In your own interest, and those of safety,
this appliance must be installed by com-
petent persons in accordance with local
and national codes of practice. Failure to
install the appliance correctly could lead to
prosecution.
1.5
Keep all plastic bags away from young
children.
1.6
Do not place any object on or near to the
stove. Allow adequate clearance above
the stove. See Figs 7, 8, 9.
1.7
The stove is fitted with the Waterford Flue
T.T.B System which will act to cut off the
gas supply to the appliance in the event of
incorrect operation of the flue. If the sys-
tem acts to shut off the gas supply, this
indicates that there is insufficient flue pull.
Continued operation of this safety device
means that there may be a serious prob-
lem with the flue system, and this should
be inspected by a qualified gas engineer.
Do not use the stove until an engineer
says it is safe to do so.
The Waterford T.T.B System must not be
tampered with. Use only genuine
Waterford replacement parts when servic
ing the system - refer to section 16.
2.
FLUE AND CHIMNEY REQUIREMENTS
2.1
The chimney or flue system must comply
with the rules in force, and must be a mini-
mum of 127mm (5") in diameter.
NOTE: IF IT IS INTENDED TO FIT THE
STOVE INTO AN EXISTING BRICK
CHIMNEY, A 127mm LINER MUST BE
USED.
2.2
The minimum effective height of the flue or
chimney must be 3 metres (10ft).
2.3
The chimney or flue must be free from any
obstruction. Any damper plates should be
removed or secured in the fully open posi-
tion, and no restrictor plates should be fit-
ted.
2.4
The chimney should be swept immediately
prior to the installation of the appliance.
However, where it can be seen that the
chimney is clean and unobstructed
through-out its entire length, it need not be
swept.
3.
VENTILATION & COMBUSTION AIR
REQUIREMENTS
This stove has a heat input of less than 7 kW and
therefore does not normally require any additional
ventilation. However, consideration must be given
to the local rules in force.
3.1
Any air vent must either be connected
direct to an outside air supply or to adja
cent rooms having a permanent vent to
the outside.
3.2
If there is another combustion appliance
fitted in the same or adjacent room, it will
be necessary to refer to the rules in force
to calculate the additional air supply.
3.3
If there is an air extraction fan fitted in the
room or adjacent rooms where this appli-
ance is fitted, additional air vents may be
required to elleviate the possibility of
spillage of products of combustion from
the appliance/flue while the fan is in oper-
ation. Refer to the rules in force.
3.4
Where such an installation exists, a test for
spillage should be made with the fan or
fans and other gas burning appliances in
operation at full rate.
3.5
If spillage occurs following the above oper-
ation, an additional air vent of sufficient
size to prevent this occurrence should be
installed.
4.
INSTALLATION OF THE GAS SUPPLY
4.1
Before installation, ensure that the local
distribution conditions (identification of
the type of gas and pressure) and the
adjustment of the appliance are compati-
ble.
4
Advertisement
