Indexa DVT50 SET Operating Instructions Manual page 35

—
button [3 - ]..
Notes:
#
All snapshots are saved to the integrated ring memory. A
maximum of 100 snapshots can be saved. When the ring memory
is full, the oldest snapshots are overwritten automatically.
#
At the top left of the snapshot you can see the door intercom
camera from which it was saved (#1 or #2), what number
image you are looking at and the total number of images (e.g.
014/089). The date and time at which the snapshot was saved are
shown at the bottom in the centre.
Factory setting: Restoring the factory settings deletes all the
snapshots
DATE AND TIME
!
By pressing the and
hours, minutes (e.g. 21:04), year, month and day (e. g. 2017 -
08 - 30) in succession.
!
Pressing the and [2] buttons changes the figure.
Notes:
#
The setting must be correct to get the exact date and time stamp on
the saved snapshots.
#
After a change of battery, the date and time must be reset.
Factory setting: not changed on reset
DOOR SET. - Volume/duration of the ring tone on the door
intercom/duration of the door release
Notes:
#
When using two mobile units, the settings for the door intercom
must be the same.
#
When using two door intercoms, the settings apply to both
intercoms.
Volume Setting for the ring tone volume on the door
intercom (1 to 9 bars)
Factory setting: 5 bars
Ring Time (s) Setting for the duration of the ring tone on the
door intercom between 0 and 15 seconds. A
setting of 0 seconds means that the ring tone is
switched off.
Factory setting: 1 second
Unlock Time (s) Setting for the duration of the door release relay
activation between 1 and 9 seconds
Factory setting: 3 seconds
LANGUAGE
Setting for the screen language
Factory setting: German
WALLPAPER - background image
Setting for the screen background (choice of 3 images)
Factory setting: Image 1
[2] buttons, you can change the
REGISTER - pairing/deletion of a door intercom
!
Move the hash # to the door intercom required.
To pair another door intercom (connected to the power supply)
!
—
press the left button
!
You now have approx. 20 seconds to complete pairing on the
door intercom.
#
DVT50 SET (1 doorbell button): Press and hold the pairing
button [27] on the door intercom until you hear three short
beeps on the intercom as confirmation that pairing has
been successful.
#
DVT50/2 SET (2 doorbel buttons): ress and hold the
pairing button [27] on the door intercom until you hear a
ringing sound, then immediately press the doorbell button
you wish to pair.
The mobile unit then makes a "plop" sound and the start
screen appears again.
To delete a door intercom
!
press the left button
!
then press the left button
Factory setting: door intercom paired (channel 1)
Notes:
#
When a mobile unit is paired with a door intercom, this is
indicated by the symbol
(no. 1 or no. 2).
#
A maximum of two mobile units can be paired with each doorbell
button. Up to two door intercoms can be used.
VERSION
The top two lines indicate the software version of the mobile unit;
below that is the version of door intercom #1 and (if present) #2.
PIR SETTINGS
This function is not available.
MONITOR SET. - image view
By pressing the buttons
views: panoramic view, full view left, middle or right.
Factory setting: panoramic view
RESET
Notes:
#
Resetting deletes all of the snapshots.
#
Following a reset, the door intercom is no longer paired with the
mobile unit.
#
The date and time are not affected by the reset.
!
To restore the factory settings, select "YES".
!
Then confirm by pressing the left button
[3-" "]. The mobile unit beeps.
—
[3 - ] ,
—
[3 - ] again to confirm.
after the door intercom number
and you can select different image
—
[3 - ].
GB - 35