Safety Instructions - Indexa DVT50 SET Operating Instructions Manual

Camera image sensor 1/4" CMOS colour
Camera resolution 640 x 480 pixel
Image angle approx. 96° (horiz.), 53° (vert.)
Illumination 6 white LEDs (illuminate close range, up
to 0.8 m, in darkness)
Radio frequency 2,412 - 2,472 GHz
Radiant emittance < 100 mA EIRP
Modulation GFSK
Radio range max. 100-150 m with clear line of sight
(depending on structural and wireless
environment)
Frame rate max. 15 images/second
Operating temperature -20° C to + 50° C (Note: below 0°C the
wireless range may be reduced)
Protection class IP 55
Dimensions 104 x 165 x 50 mm (with protective cover)
Mobile unit DVT50M
Lithium battery 3,7 V, 1100 mAh
Battery power drop app. 10% after 300 charging cycles
Charging power via charging station
Initial charging time 5 hours
Standby time up to 18 hours without charging
Conversation time up to 2-3 hours without charging
Power consumption max. 400 mA
Radio frequency 2,412 - 2,472 GHz
Radiant emittance < 100 mA EIRP
Wireless modulation GFSK
Diagonal screen size 2.4" (6.1 cm)
Monitor resolution 240 x 320 pixel
Integrated image storage ring memory, max. 100 snapshots
Operating temperature
Dimensions 53 x 187 x 26 mm
Charging station DVT50L
Power supply 12 V
Power consumption max. 300 mA
Operating temperature ± 0° C bis + 40° C
Dimensions 80 x 105 x 95 mm
Power supply for charging station
Power supply 230 V ~ AC, 50 Hz
Output 12 V
Application indoor use only

6. Safety instructions

The following instructions are provided for your safety and satisfaction
during operation of the device. Note that non-observance of these
safety instructions results in significant risks of accident.
Danger! Failure to comply with the following instructions can
cause fatal injury, damage to health and material damage.
± 0° C to + 40° C
"
DC (mains adapter)
"
DC, 500 mA
!
Do not leave small children unsupervised with the device,
packaging material or small parts. Otherwise there is a risk of
fatal injury due to choking or suffocation.
!
Do not damage any gas, electricity, water or telecommunication
lines during drilling and fixing work. Otherwise there are dangers
of fire, personal and fatal injury.
!
Treat the cables carefully. Lay these so that they cannot be
damaged and do not present any tripping hazard. Do not pull the
cables over sharp edges and do not crush or crimp them
elsewhere. Otherwise there are dangers of fire, personal and fatal
injury.
!
To prevent injuries, secure the door inter- face reliably in
accordance with the installation instructions.
!
Ensure that the devices (apart from the door intercom: IP55) and
the power supply unit do not come into contact with moisture and
do not submerge in water. Otherwise there is a danger of fatal
injury.
!
Only operate the charging station from the supplied power
supply. Before connecting the power supply to the mains, ensure
that the mains current complies with 230 V ~, 50 Hz and is
fitted with a fuse according to regulations.
!
When connecting to the mains, ensure that the door intercom is
supplied with the specified voltage by cable and that the mains
current complies with 230 V ~, 50 Hz and is fitted with a fuse
according to regulations.
!
Perform the connection and installation while the mains power is
disconnected! Otherwise there is a risk of fatal injury due to
electric shock.
!
Do not connect any external voltage to the connection terminals.
Otherwise there are dangers of personal and fatal injury and fire.
!
Ensure that the batteries are not short circuited or exposed to fire.
The batteries must not be opened or recharged. Otherwise there is
a risk of fatal injury due to explosion!
!
Leaking or damaged batteries can cause burns by contact with
skin. Handle these using suitable protective gloves.
!
Use only the recommended battery types.
!
Attention! Danger of explosion if the battery is not replaced
correctly. Replace only by the same or equivalent battery type.
!
Insert the batteries with the correct polarity.
!
If the device is not to be used for some period remove the
batteries.
!
Do not place the equipment and the batteries near fire, heat or in
areas of high temperature.
!
Protect the equipment and the cables against strong magnetic or
electrical fields and against strong mechanical loads and
vibrations.
!
Only use the equipment with the supplied original parts or
original accessories.
!
Before assembly and use check that all parts are included and
that they are undamaged.
GB - 29