Indexa DVT50 SET Operating Instructions Manual page 33

#
A symbol on the top left of the camera image on the screen
indicates whether the door intercom showing the camera image is
being supplied with power by the power supply unit (
batteries ( ) .
#
If there is a ring on the intercom and a snapshot is saved but the
conversation is not accepted on a mobile unit, (at least) one new
snapshot is indicated by the flashing red
left of the screen. As soon as the "Snap Show" menu item is
selected, the symbol disappears.
#
Transmission of sound is only available while the talk function is
activated.
11.2 Switching on the intercom camera image
manually
!
With the mobile unit switched on, press any button
[1/2/3/5/7/8] to make the start screen [6] appear.
!
—
Press the right button
paired door intercom, its camera image appears automatically;
with two paired intercoms, use the
the intercom required, confirm by pressing the left button
- "Select"]and the camera image appears.
As long as the camera image is visible, the following options are
available:
!
To take a static image and save it on the mobile unit, press the
—
right button [7]; the
!
By pressing the talk button [1], you can activate the talk function:
either the sound from the microphone [21] on the door intercom
can be heard over the loudspeaker [10] on the mobile unit or the
sound from the microphone [4] on the mobile unit can be heard
over the loudspeaker [18] on the door intercom in alternation
(intercom function).
The talk function can be ended by pressing the on/off button
[8]; otherwise, it ends automatically after approx. 45 seconds,
the start screen appears again and the screen goes off after
approx. 20 seconds.
!
Pressing the door release button [5] activates a connected door
release, the start screen appears again and the screen switches off
after approx. 20 seconds.
!
To switch the camera off again, press the on/off button
otherwise, this happens automatically after approx. 45 seconds,
the start screen appears again and the screen switches off after
approx. 20 seconds.
Note:
When operating the door intercom with batteries, it is
not possible to switch the camera image on manually
the intercom is supplied in energy-saving mode. "Monitor" appears on
the black screen. (In energy-saving mode, the camera image is
displayed only when the ring button [25] is pressed).
If you still wish to be able to switch the camera image on manually, you
have to switch the door intercom to energy consumption mode (please
symbol at the top
[7 - "Mon" (Monitor)]. With only one
and [2] buttons to select
symbol appears briefly.
note: in this case, the batteries in the intercom will go flat significantly
more quickly):
!
) or by Press the pairing button [27] on the door intercom until you hear
a long beep
!
Press the pairing button on the door intercom a second time until
you hear two ding-dongs and a
!
Press the pairing button a third time until you hear
beeps .
To return to energy-saving mode,
!
press the pairing button [27] on the door intercom until you hear
two ding-dongs and
12. Optional addition of a DVT50M
mobile unit and/or a DVT50T /
DVT50T2door intercom
DVT50 SET
The mobile unit of the DVT50 SET has already been paired with the
door intercom on channel No. 1. A maximum of
—
[3
and/or one more door intercom
system.
To establish a wireless connection between a DVT50T door intercom
and a DVT50M mobile unit, pair them as follows:
!
The door intercom and mobile unit must both have a power
supply and the mobile unit must be switched on.
!
Press any button [1/2/3/5/7/8] on the mobile unit to make the
start screen appear.
!
Press the left button
!
Scroll through the menu with the
reach "Register" and press the left button
You can select between door intercom of the set (channel no. 1) or
a second door intercom (channel 2).
!
Move the hash # to the channel you require by pressing [2]:
#
To connect an additional mobile unit to the door intercom of
the DVT50 SET, select channel No. 1.
#
To connect a mobile unit to a second door intercom, select
channel No. 2.
!
Press the left button
[8];
you now have approx. 20 seconds to complete pairing.
!
Press and hold the pairing button [27] on the door intercom until
you hear three short beeps on the intercom as confirmation that
pairing has been successful; the mobile unit then makes a "plop"
sound and the start screen appears again.
as
DVT50/2 SET
Both mobile units of the DVT50/2 SET have already been paired with
the door intercom on channel No. 1, one with the upper and one with
the lower doorbell button. Each doorbell button can be paired with a
second mobile unit.
.
long beep
three short beeps .
can be connected to the existing
—
[3 - "Menu"] to open the menu.
and [2] buttons until you
—
[3 - " "]. The mobile unit beeps and
.
three short
one more mobile unit
—
[3 - "Select"].
GB - 33