LIABILITY MAGIC FX accepts no liability for claims from third parties arising from unauthorised use, use other than that stated in this manual, and use other than in accordance with the General Conditions registered at the Chamber of Commerce.
Noise level Safety symbols 2.7 Precautions for operation Let’s blast! Install the machine Fill with confetti and blast Replace a CO cylinder Clean up Troubleshooting Maintenance Correct disposal EC Declaration of Conformity 7.1 SUPERBLASTER 7.2 SUPERBLASTER XL MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
FOREWORD Congratulations! You have bought a great new product from MAGIC FX. This manual contains all information required for the intended use of the equipment. Deviation from the described intended use can result in a hazardous situation and/or property damage.
CO valve. To keep the effect going the operator must continuously fill the hopper with confetti. MAIN PARTS WOOFER HOPPER INPUT VALVE FLIGHTCASE Main parts MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
Type plate CONFETTI The MAGICFX® SUPERBLASTER (XL) can be set in 4 different angles between 42° and 90°. The output height and output distance depend on the type of confetti and the set angle. The maximum load per blast also depends on the type of confetti. Check the following table.
Always consult your CO supplier for regulations and instructions on safe installation and use. MAGIC FX is not liable for unsafe situations, accidents and damage that are the result of incorrect working with CO gas and CO cylinders.
INDOOR USE The MAGICFX SUPERBLASTER (XL) is designed for outdoor use and use in well- ® ventilated indoor spaces. When used indoors, make sure you take the necessary preparations. These preparations could include, but are not limited to: • Consulting your CO supplier.
Make sure there are no objects near the output that can be WARNING damaged or overthrown by the MAGICFX SUPERBLASTER (XL). ® Always create a safety zone with a distance of 3 m around the WARNING MAGICFX SUPERBLASTER (XL). ® top view 10 MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
LET’S BLAST! INSTALL THE MACHINE Bring the cased MAGICFX SUPERBLASTER (XL) to the desired location. ® Unlock and remove the top cover. MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
Page 12
Place and hold the woofer in the case and insert a pin through the front pinholes. Make sure that the CO input of the woofer is positioned at the front. MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
Page 13
Secure the pin with a clip. Set the angle of the woofer by aligning the back pinhole with one of the four predefined holes in the case. 48º 32º 16º 0º MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
Page 14
Insert the second pin through the back pinholes to secure the position of the woofer. Secure the pin with a clip. MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
Page 15
Position the machine and set the brakes. Take the necessary safety precautions, see Section 2.7. Connect the CO valve to the CO input of the woofer and tighten the nut with the adjustable wrench. MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
Page 16
Connect the CO hose to the CO valve. Make sure that the CO valve is in CLOSED position. MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
Page 17
Connect the CO₂ Bottle to Hose Connector to a CO cylinder. Connect the CO hose to the CO₂ Bottle to Hose Connector on the CO cylinder. Open the CO cylinder. MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual 17...
Make sure that the prescribed safety zone is free from persons and objects. When it’s time to blast, move the manual CO valve in OPEN position. Keep filling the hopper with confetti by hand. MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
Page 19
Enjoy the view! When you are finished with blasting confetti, move the manual CO valve back in CLOSED position. MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
REPLACE A CO CYLINDER Make sure that the CO valve is in CLOSED position. Close the connected CO cylinder. Move the manual CO valve in OPEN position to release the pressure from the system. 20 MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
Page 21
Bottle to Hose Connector on the CO cylinder. Remove the CO Bottle to Hose Connector from the cylinder. Connect a CO Bottle to Hose Connector to a new CO cylinder. MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
Page 22
Connect the CO hose to the CO Bottle to Hose Connector on the new CO cylinder. Move the manual CO valve back in the CLOSED position. Open the CO cylinder. MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
CLEAN UP Close the connected CO cylinder. Move the manual CO valve in OPEN position to release the pressure from the system. Remove the CO hose. MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
Page 24
Fasteners in the vicinity of the output pipe can become frozen NOTICE due to the use of CO . If necessary, wait until these fasteners are defrosted before you try to release them. MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
Page 25
Unscrew the nut and remove the valve. Unlock and remove the pins while holding the woofer and remove the woofer. Remove remaining confetti from the hopper. MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
Page 26
Store all parts in the case. Place and lock the top cover. MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
TROUBLESHOOTING Always contact MAGIC FX if any malfunctions or errors occur that cannot be solved with the instructions as described in this manual. MAINTENANCE To achieve the maximum service life of the MAGICFX SUPERBLASTER (XL) you must ® regularly clean the MAGICFX SUPERBLASTER (XL) and test if it is functioning correctly.
EC DECLARATION OF CONFORMITY DECLARATION OF CONFORMITY 7.1 SUPERBLASTER MAGIC FX B.V. declares as manufacturer and composer of the technical construction file that the product with the following specifications: Name machine : SUPER BLASTER Type : MFX0801 Serial number : on product...
DECLARATION OF CONFORMITY 7.2 SUPERBLASTER XL MAGIC FX B.V. declares as manufacturer and composer of the technical construction file that the product with the following specifications: Name machine : SUPER BLASTER XL Type : MFX0802 Serial number : on product...
Page 30
30 MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...
Page 31
MAGICFX® SUPERBLASTER & SUPERBLASTER XL — User and Installation Manual...